Technician License Course Chapter 4

Slides:



Advertisements
Similar presentations
Amateur Radio Technician Class Element 2 Course Presentation
Advertisements

Propagation of Waves Ham Radio Class Week 5 Wave propagation.
Intermediate Course (6) Propagation Karl Davies Intermediate Course (6) Propagation Karl Davies East Kent Radio Society EKRS 1.
Radio Waves and Signals Week 4. We imagine radio signals/waves travel as sine waves. The ripple of these waves are started by the vibration of an electron.
Chapter 3 – Radio Phenomena
SUBELEMENT T3 [3 Exam Questions - 3 Groups] Radio wave characteristics, radio and electromagnetic properties, propagation modes.
Technician Licensing Class “T3” Valid dates: July 1, 2010 – June 30, 2014.
General License Class Chapter 7 Propagation.
For HF Beginners Gary Wescom – N0GW
Amateur Radio Frequency Propagation
Introduction Syllabus covers a wide range of propagation topics:-
HOW DOES MY SIGNAL GET FROM HERE TO THERE? By Forest Cummings, W5LQU And Dave Russell, W2DMR.
Chapter Fifteen: Radio-Wave Propagation
Radio Frequencies. Oscillator Feedback loop Oscillator As the output of the amplifier is fed to the input, feedback or oscillation occurs.
Chapter 10 Topics in Radio Propagation Rick, WØPC.
Technician Licensing Class Weak Signal Propagation Section 15 Valid July 1, 2014 Through June 30, 2018.
1 of 12 Chelmsford Amateur Radio Society Intermediate Licence Course Christopher Chapman G0IPU Slide Set 8 (6) Propagation Chelmsford Amateur Radio Society.
Propagation of radio waves. Ways of travelling Propagation in ionosphere Propagation in troposphere Special ways of reflecting Propagation depends on.
Technician Licensing Class Supplement T3, Questions Only Radio Wave Characteristics 3 Exam Questions, 3 Groups.
Lesson 4 Propagation, Antennas, Feed Lines
KL2IW Norman Ayagalria. 2  Vertical antennas are perpendicular to earth  low “take-off” angle good for long distance comms  Limited bandwidth compared.
Technician License Course Chapter 2 Radio and Electronics Fundamentals
Technician License Course Chapter 3 Electricity, Components and Circuits Lesson Plan Module 6.
Technician License Class Gordon West Technician Class Manual Pages Weak Signals Presented by Heart Of Texas Amateur Radio Club (HOTARC)
How Radio Waves Act Similar to Book Chapter 2 – sections 2.4 and 2.6.
General Licensing Class G3A – G3C Radio Wave Propagation Your organization and dates here.
General Licensing Class Skywave Excitement Your organization and dates here.
Chapter 7 Propagation The Ionosphere
1 Technician Licensing Class T 3 A - T 3 C Valid July 1, 2014 Through June 30, 2018.
SUBELEMENT G3 RADIO WAVE PROPAGATION [3 Exam Questions - 3 Groups]
Technician Licensing Class Weak Signal Propagation Page 92 to 98.
Radio Propagation Technician License Class Session 3 N1AW revised 4/2013.
Understand band condition information Use a propagation gadget
Technician Licensing Class Weak Signal Propagation Lake Area Radio Klub Spring 2012.
Technician Licensing Class Weak Signal Propagation Section 15.
Radio & Telecommunications Systems 1 Radio & Telecommunications Systems (1.0) Lecturer: P.M. Cheung (room 326) Contact Hours:
Radio Wave Propagation. VLF ( 3 – 30 KHz) and LF (30 – 300 KHz) Propagation Marc C. Tarplee, Ph.D. ARRL Technical Coordinator SC Section.
Hi-Landers Ham Class Instructed by Rich Bugarin W6EC.
Technician License Course Chapter 3
Technician License Course Chapter 4
Technician Licensing Class Emergency!. 2 Pass out “Radiogram” and/or other forms.
SUBELEMENT T3 Radio wave characteristics: properties of radio waves; propagation modes [3 Exam Questions - 3 Groups] 1 Radio Waves 2014.
Practice Questions 2015 General License Course. How is a directional antenna pointed when making a “long-path” contact with another station? A. Toward.
Radio Wave Propagation
By Saneeju m salu. Radio waves are one form of electromagnetic radiation RADIO WAVES.
Performance of long-distance VHF-band communication links based on scattering from perturbed Ionosphere. מציגים : יואב צידון שי ביטון מנחה : פרופ ' נתן.
Technician Licensing Class
Antennas, Feed lines, and Propagation
Larry, WB9KMW.
Technician License Course Chapter 3
Chapter 8 Antennas Propagation Dave Piersall, N6ORB.
FACULTY DEVELOPMENT PROGRAMME on EC ANTENNA AND WAVE PROPAGATION
Instructed by Rich Bugarin W6EC
The HF Bands For HF Beginners Gary Wescom – N0GW.
Sky Wave Propagation.
Technician Licensing Class
Technician Licensing Class
The Sun and HF Propagation
Lecture 4: Wave Propagation Concept
Technician Licensing Class
Technician License Class Session 2
Chelmsford Amateur Radio Society Intermediate Course (6) Propagation
Technician Licensing Class
Why are direct (not via a repeater) UHF signals rarely heard from stations outside your local coverage area? A. They are too weak to go very far B. FCC.
Chelmsford Amateur Radio Society Intermediate Course (6) Propagation
What should you do if another operator reports that your station’s 2 meter signals were strong just a moment ago, but now they are weak or distorted? A.
Before You Start To be able to properly view this PowerPoint you have to be in Slide Show mode. If all you see is this slide you should be all ready to.
Roanoke Valley Amateur Radio Club
Technician License Course.
General Licensing Class
Presentation transcript:

Technician License Course Chapter 4 Make sure you bring in lots of examples of antennas and different kinds of feed lines as examples are you are going through this lesson. Lesson Plan Module 8 - Propagation

Radio Wave Propagation: Getting from Point A to Point B Radio waves propagate by many mechanisms. The science of wave propagation has many facets. We will discuss three basic ways: Line of sight Ground wave Sky wave

Line-of-Sight If a source of radio energy can been seen by the receiver, then the radio energy will travel in a straight line from transmitter to receiver. There is some attenuation of the signal as the radio wave travels This is the primary propagation mode for VHF and UHF signals. Line-of-sight is probably the easiest propagation mode for students to understand. You can use a laser pointer to demonstrate line-of-sight. You will probably have to refresh the students memory on UHF and VHF definitions and their position on the RF spectrum. Also these bands will be the primary operating bands of the new hams. The maximum distance for line-of-sight transmissions with two people standing on the surface of the earth is about (roughly) 25 miles, this is due to the curvature of the earth. You can extend this discussion by briefly brining up repeaters and how they extend the line-of-sight range.

Ground Wave Some radio frequency ranges (VLF, LF, MF and lower HF frequencies) will hug the earth’s surface as they travel. These waves will travel beyond the range of line-of-sight. A few hundred miles for HF. Point out that this propagation mode is the one used by AM broadcast stations in the day light hours. You can connect with the students experiences with receiving AM broadcast stations using ground waves. What happens at night? Why do they change power levels depending on the time of day? How is the reception at night?

VHF and UHF Propagation VHF & UHF propagation is principally line of sight. Range is slightly better (15%) than visual line of sight. UHF signals may work better inside buildings because of the shorter wavelength. Buildings may block line of sight, but reflections may help get past obstructions. Line-of-sight is probably the easiest propagation mode for students to understand. You can use a laser pointer to demonstrate line-of-sight. You will probably have to refresh the students memory on UHF and VHF definitions and their position on the RF spectrum. Also these bands will be the primary operating bands of the new hams. The maximum distance for line-of-sight transmissions with two people standing on the surface of the earth is about (roughly) 25 miles, this is due to the curvature of the earth. You can extend this discussion by briefly brining up repeaters and how they extend the line-of-sight range.

VHF and UHF Propagation Reflections from a transmitter that is moving cause multi-path which results in rapid fading of signal – known as picket fencing. Atmospheric inversions can cause VHF and UHF signals to travel long distances. This is known as tropospheric ducting. UHF signals are normally not reflected by the ionosphere.

VHF and UHF Propagation Line-of-sight is probably the easiest propagation mode for students to understand. You can use a laser pointer to demonstrate line-of-sight. You will probably have to refresh the students memory on UHF and VHF definitions and their position on the RF spectrum. Also these bands will be the primary operating bands of the new hams. The maximum distance for line-of-sight transmissions with two people standing on the surface of the earth is about (roughly) 25 miles, this is due to the curvature of the earth. You can extend this discussion by briefly brining up repeaters and how they extend the line-of-sight range.

Sunspot Cycle The level of atmospheric ionization depends on the radiation intensity of the Sun. Radiation from the Sun is connected to the number of sunspots on the Sun’s surface. High number of sunspots, high ionizing (UV) radiation emitted from the Sun. Sunspot activity follows an 11-year cycle. Here is a good place to discuss the sun spot cycle, some of the students might make the connection between this practical application of science and the study of the sun and to some things they have heard about sun spots on the evening news programs.

Ionosphere UV radiation from the Sun momentarily will strip electrons away from the parent atom in the upper reaches of the atmosphere. Creates ions The region where ionization occurs is called the ionosphere. Discuss with the students what happens to ionize the upper reaches of the atmosphere. You may have to tap into some old science lessons and vocabulary that the students haven’t thought about in years. Define what an Ion is. The concept of momentarily stripping away the electrons is important when you get into the details of the layers of the ionosphere and the time it takes for the ionosphere to dissipate during the evening and night time hours. You can also refer back to the students experience with AM broadcasts and what they observe at night versus what they observe during the day time.

Levels of the Ionosphere Density of the atmosphere affects: The intensity of the radiation that can penetrate to that level. The amount of ionization that occurs. How quickly the electrons recombine with the nucleus.

Ionospheric Layers The D layer mostly absorbs radio signals, and is not favorable to communications. Fades at night The E layer may provide sporadic medium distance communications for HF and lower frequency VHF radio signals. Most long distance HF communications are through the F layers. The F1 and F2 layers form during the day. At night they recombine into a single layer. If the angle is too steep, the waves go right through. If the frequencies are too low or too high, they also are not reflected, and in some cases are absorbed by the layer. Constant monitoring of the ionosphere indicates the maximum and minimum usable frequencies for sky-wave propagation. Hams interested in DX (you might have to explain DX) will adjust their operating bands to take advantage of those frequencies that are reflected off the ionosphere.

The Ionosphere – An RF Mirror The ionized layers of the atmosphere actually act as an RF mirror or prism that reflect certain frequencies back to earth. Sky-wave propagation is responsible for most long-range, over the horizon communication. Reflection depends on ionization level, signal frequency and angle of incidence.

What should you do if another operator reports that your station’s 2 meter signals were strong just a moment ago, but now they are weak or distorted? (T3A01) A. Change the batteries in your radio to a different type B. Turn on the CTCSS tone C. Ask the other operator to adjust his squelch control D. Try moving a few feet, as random reflections may be causing multi-path distortion

What should you do if another operator reports that your station’s 2 meter signals were strong just a moment ago, but now they are weak or distorted? (T3A01) A. Change the batteries in your radio to a different type B. Turn on the CTCSS tone C. Ask the other operator to adjust his squelch control D. Try moving a few feet, as random reflections may be causing multi-path distortion

Why are UHF signals often more effective from inside buildings than VHF signals. (T3A02) A. VHF signals lose power faster over distance B. The shorter wavelength allows them to more easily penetrate the structure of buildings C. This is incorrect: VHF works better than UHF inside buildings D. UHF antennas are more efficient than VHF antennas

Why are UHF signals often more effective from inside buildings than VHF signals. (T3A02) A. VHF signals lose power faster over distance B. The shorter wavelength allows them to more easily penetrate the structure of buildings C. This is incorrect: VHF works better than UHF inside buildings D. UHF antennas are more efficient than VHF antennas

What term is commonly used to describe the rapid fluttering sound sometimes heard from mobile stations that are moving while transmitting? (T3A06) A. Flip-flopping B. Picket fencing C. Frequency shifting D. Pulsing

What term is commonly used to describe the rapid fluttering sound sometimes heard from mobile stations that are moving while transmitting? (T3A06) A. Flip-flopping B. Picket fencing C. Frequency shifting D. Pulsing

What is the cause of irregular fading of signals from distant stations during times of generally good reception? (T3A08) A. Absorption of signals by the “D” layer of the ionosphere B. Absorption of signals by the “E” layer of the ionosphere C. Random combining of signals arriving via different path lengths D. Intermodulation distortion in the local receiver

What is the cause of irregular fading of signals from distant stations during times of generally good reception? (T3A08) A. Absorption of signals by the “D” layer of the ionosphere B. Absorption of signals by the “E” layer of the ionosphere C. Random combining of signals arriving via different path lengths D. Intermodulation distortion in the local receiver

What may occur if VHF or UHF data signals propagate over multiple paths? (T3A10) A. Transmission rates can be increased by a factor equal to the number of separate paths observed B. Transmission rates must be decreased by a factor equal to the number of separate paths observed C. No significant changes will occur if the signals are transmitting using FM D. Error rates are likely to increase

What may occur if VHF or UHF data signals propagate over multiple paths? (T3A10) A. Transmission rates can be increased by a factor equal to the number of separate paths observed B. Transmission rates must be decreased by a factor equal to the number of separate paths observed C. No significant changes will occur if the signals are transmitting using FM D. Error rates are likely to increase

Which part of the atmosphere enables the propagation of radio signals around the world? (T3A11) A. The stratosphere B. The troposphere C. The ionosphere D. The magnetosphere

Which part of the atmosphere enables the propagation of radio signals around the world? (T3A11) A. The stratosphere B. The troposphere C. The ionosphere D. The magnetosphere

Why are “direct” (not via a repeater) UHF signals rarely heard from stations outside your local coverage area? (T3C01) A. They are too weak to go very far B. FCC regulations prohibit them from going more than 50 miles C. UHF signals are usually not reflected by the ionosphere D. They collide with trees and shrubbery and fade out

Why are “direct” (not via a repeater) UHF signals rarely heard from stations outside your local coverage area? (T3C01) A. They are too weak to go very far B. FCC regulations prohibit them from going more than 50 miles C. UHF signals are usually not reflected by the ionosphere D. They collide with trees and shrubbery and fade out

Which of the following might be happening when VHF signals are being received from long distances? (T3C02) A. Signals are being reflected from outer space B. Signals are arriving by sub-surface ducting C. Signals are being reflected by lightning storms in your area D. Signals are being refracted from a sporadic E layer

Which of the following might be happening when VHF signals are being received from long distances? (T3C02) A. Signals are being reflected from outer space B. Signals are arriving by sub-surface ducting C. Signals are being reflected by lightning storms in your area D. Signals are being refracted from a sporadic E layer

What is a characteristic of VHF signals received via auroral reflection? (T3C03) A. Signals from distances of 10,000 or more miles are common B. The signals exhibit rapid fluctuations of strength and often sound distorted C. These types of signals occur only during winter nighttime hours D. These types of signals are generally strongest when your antenna is aimed to the south (for stations in the Northern Hemisphere)

What is a characteristic of VHF signals received via auroral reflection? (T3C03) A. Signals from distances of 10,000 or more miles are common B. The signals exhibit rapid fluctuations of strength and often sound distorted C. These types of signals occur only during winter nighttime hours D. These types of signals are generally strongest when your antenna is aimed to the south (for stations in the Northern Hemisphere)

Which of the following propagation types is most commonly associated with occasional strong over-the-horizon signals on the 10, 6, and 2 meter bands? (T3C04) A. Backscatter B. Sporadic E C. D layer absorption D. Gray-line propagation

Which of the following propagation types is most commonly associated with occasional strong over-the-horizon signals on the 10, 6, and 2 meter bands? (T3C04) A. Backscatter B. Sporadic E C. D layer absorption D. Gray-line propagation

What is meant by the term “knife-edge” propagation? (T3C05) A. Signals are reflected back toward the originating station at acute angles B. Signals are sliced into several discrete beams and arrive via different paths C. Signals are partially refracted around solid objects exhibiting sharp edges D. Signals are propagated close to the band edge exhibiting a sharp cutoff

What is meant by the term “knife-edge” propagation? (T3C05) A. Signals are reflected back toward the originating station at acute angles B. Signals are sliced into several discrete beams and arrive via different paths C. Signals are partially refracted around solid objects exhibiting sharp edges D. Signals are propagated close to the band edge exhibiting a sharp cutoff

What mode is responsible for allowing over-the-horizon VHF and UHF communications to ranges of approximately 300 miles on a regular basis? (T3C06) A. Tropospheric scatter B. D layer refraction C. F2 layer refraction D. Faraday rotation

What mode is responsible for allowing over-the-horizon VHF and UHF communications to ranges of approximately 300 miles on a regular basis? (T3C06) A. Tropospheric scatter B. D layer refraction C. F2 layer refraction D. Faraday rotation

What band is best suited to communicating via meteor scatter? (T3C07) A. 10 meters B. 6 meters C. 2 meters D. 70 cm

What band is best suited to communicating via meteor scatter? (T3C07) A. 10 meters B. 6 meters C. 2 meters D. 70 cm

What causes “tropospheric ducting?” (T3C08) A. Discharges of lightning during electrical storms B. Sunspots and solar flares C. Updrafts from hurricanes and tornados D. Temperature inversions in the atmosphere

What causes “tropospheric ducting?” (T3C08) A. Discharges of lightning during electrical storms B. Sunspots and solar flares C. Updrafts from hurricanes and tornados D. Temperature inversions in the atmosphere

What is generally the best time for long-distance 10 meter band propagation? (T3C09) A. During daylight hours B. During nighttime hours C. When there are coronal mass ejections D. Whenever the solar flux is low

What is generally the best time for long-distance 10 meter band propagation? (T3C09) A. During daylight hours B. During nighttime hours C. When there are coronal mass ejections D. Whenever the solar flux is low

What is the radio horizon? (T3C10) A. The distance at which radio signals between two points are effectively blocked by the curvature of the earth B. The distance from the ground to a horizontally mounted antenna C. The farthest point you can see when standing at the base of your antenna tower D. The shortest distance between two points on the Earth’s surface

What is the radio horizon? (T3C10) A. The distance at which radio signals between two points are effectively blocked by the curvature of the earth B. The distance from the ground to a horizontally mounted antenna C. The farthest point you can see when standing at the base of your antenna tower D. The shortest distance between two points on the Earth’s surface

Why do VHF and UHF radio signals usually travel somewhat farther than the visual line of sight distance between two stations? (T3C11) A. Radio signals move somewhat faster than the speed of light B. Radio waves are not blocked by dust particles C. The Earth seems less curved to radio waves than to light D. Radio waves are blocked by dust particles

Why do VHF and UHF radio signals usually travel somewhat farther than the visual line of sight distance between two stations? (T3C11) A. Radio signals move somewhat faster than the speed of light B. Radio waves are not blocked by dust particles C. The Earth seems less curved to radio waves than to light D. Radio waves are blocked by dust particles