Low Energy and Low Current S-Band Traveling Wave Electron Linear Accelerator structure design Hamed Shaker School of Particles and Accelerators Institute.

Slides:



Advertisements
Similar presentations
Introduction to RF for Accelerators
Advertisements

CHAPTER 3 MICROWAVE ‘O’ TYPE TUBES
Shuichi Noguchi, KEK6-th ILC School, November Shuichi Noguchi, KEK6-th ILC School, November RF Basics; Contents  Maxwell’s Equation  Plane.
PH0101 Unit 2 Lecture 4 Wave guide Basic features
Normal-Conducting Photoinjector for High Power CW FEL Sergey Kurennoy, LANL, Los Alamos, NM, USA An RF photoinjector capable of producing high continuous.
S. N. “ Cavities for Super B-Factory” 1 of 38 Sasha Novokhatski SLAC, Stanford University Accelerator Session April 20, 2005 Low R/Q Cavities for Super.
DUAL FEED RF GUN DESIGN FOR LCLS Liling XIAO, Zenghai LI Advanced Computations Department Stanford Linear Accelerator Center Nov , SLAC-LCLS Injector.
Design of Standing-Wave Accelerator Structure
Cell-Coupled Drift Tube Linac M. Pasini, CERN AB-RF LINAC4 Machine Advisory Committee 1 st meeting CERN January 29-30, 2008.
Beam loading compensation 300Hz positron generation (Hardware Upgrade ??? Due to present Budget problem) LCWS2013 at Tokyo Uni., Nov KEK, Junji.
Accelerators We’ve seen a number of examples of technology transfer in particle detector development from HEP (basic science) to industry (medical, …)
Eric Prebys, FNAL.  We consider motion of particles either through a linear structure or in a circular ring USPAS, Knoxville, TN, Jan , 2014 Lecture.
Sub-Harmonic Buncher design for CLIC Drive Beam Injector Hamed Shaker School of Particles and Accelerators Institute for Research in Fundamental Sciences,
201 MHz and 805 MHz Cavity Developments in MUCOOL Derun Li Center for Beam Physics Lawrence Berkeley National Laboratory Nufact 2002 Workshop, London,
1 Basics of Microwave Measurements Steven Anlage
Photocathode 1.5 (1, 3.5) cell superconducting RF gun with electric and magnetic RF focusing Transversal normalized rms emittance (no thermal emittance)
Clustered Surface RF Production Scheme Chris Adolphsen Chris Nantista SLAC.
RF structure design KT high-gradient medical project kick-off Alberto Degiovanni TERA Foundation - EPFL.
704MHz Warm RF Cavity for LEReC Binping Xiao Collider-Accelerator Department, BNL July 8, 2015 LEReC Warm Cavity Review Meeting  July 8, 2015.
Travelling Wave Tube For Broadband amplifier helix TWTs (proposed by Pierce and others in 1946 ) are widely used For High average power purposes the.
January 5, 2004S. A. Pande - CAT-KEK School on SNS MeV Injector Linac for Indian Spallation Neutron Source S. A. PANDE.
PROPOSAL G.I.A.F. (HYBRID GUN AT HIGH FREQUENCY) INFN-LNF – UNIVERSITY OF ROME “LA SAPIENZA”- UCLA D. Alesini (T), M. Ferrario (R), A. Gallo (T),
Yi HUANG Department of Electrical Engineering & Electronics
Design of Microwave Undulator Cavity
CLARA Gun Cavity Optimisation NVEC 05/06/2014 P. Goudket G. Burt, L. Cowie, J. McKenzie, B. Militsyn.
2.1 GHz Warm RF Cavity for LEReC Binping Xiao Collider-Accelerator Department, BNL June 15, 2015 LEReC Warm Cavity Review Meeting  June 15, 2015.
RF scheme of electron linear accelerator with energy MeV Levichev A.E. Budker Institute of Nuclear Physics SB RAS.
Group 6 / A RF Test and Properties of a Superconducting Cavity Mattia Checchin, Fabien Eozénou, Teresa Martinez de Alvaro, Szabina Mikulás, Jens Steckert.
PBG Structure Experiments, AAC 2008 Photonic Bandgap Accelerator Experiments Roark A. Marsh, Michael A. Shapiro, Richard J. Temkin Massachusetts Institute.
Measurements of the X-ray/pump laser pulse timing Valery Dolgashev, David Fritz, Yiping Feng, Gordon Bowden SLAC 48th ICFA Advanced Beam Dynamics Workshop.
Beam breakup and emittance growth in CLIC drive beam TW buncher Hamed Shaker School of Particles and Accelerators, IPM.
Chapter 16 Waves-I Types of Waves 1.Mechanical waves. These waves have two central features: They are governed by Newton’s laws, and they can exist.
Microwave Devices.
DEVELOPMENT OF A STEADY STATE SIMULATION CODE FOR KLYSTRONS
Lecture 2. Review lecture 1 Wavelength: Phase velocity: Characteristic impedance: Kerchhoff’s law Wave equations or Telegraphic equations L, R, C, G ?
Eric Prebys, FNAL.  We consider motion of particles either through a linear structure or in a circular ring USPAS, Hampton, VA, Jan , 2015 Longitudinal.
P212c33: 1 Electromagnetic Waves Maxwell’s Equations.
TESLA DAMPING RING RF DEFLECTORS DESIGN F.Marcellini & D. Alesini.
Status of work on the HOM coupler. 2 nd Harmonic cavity Meeting 11/II-2016 Thermal analyses with shims (Y.Terechkine). Gennady Romanov On behalf of Y.Terechkine.
4/26/2013 Irina PetrushinaDeflecting cavity MHz for PXIE Irina Petrushina 4/26/2013.
Helical Accelerating Structure with Controllable Beam Emittance S.V. Kuzikov 1, A.A. Vikharev 1, J.L. Hirshfield 2,3 1 Institute of Applied Physics RAS,
Multipacting Simulation for the PITZ RF Photo Gun Igor Isaev Unwanted Beam Workshop 2012 Humboldt-University Berlin, The PITZ RF Photo Gun.
C/S band RF deflector for post interaction longitudinal phase space optimization (D. Alesini)
20/3/2014 MEW weekly meeting Summary on high efficiency klystron design Chiara Marrelli.
–11.03 Hawaii Multi bunch acceleration on LUCX system Ⅰ. LUCX project Ⅱ. Simulation results for Compton scattering Ⅲ. Calculation on beam loading.
HG 2016 Workshop Design of Metallic Subwavelength Structures for Wakefield Acceleration Xueying Lu, Michael Shapiro, Richard Temkin Plasma Science and.
Advancements on RF systems D. Alesini (LNF-INFN) Quinto Meeting Generale Collaborazione LI2FE, Frascati 15-16/03/2011.
Status of the sub-harmonic bunching system for the CLIC DB injector front end Hamed Shaker School of Particles and Accelerators, Institute for Research.
How does a klystron work? TE-MPE Section Meeting Karolina Kulesz
S.M. Polozov & Ko., NRNU MEPhI
High efficiency work and MBK development for accelerators
Bunching system for SPES project
Development of X-band 50MW klystron in BVERI
M. Migliorati, C. Vaccarezza INFN - LNF
NC Accelerator Structures
Physics design on Injector-1 RFQ
Ch32: Electromagnetic Waves
Notes 5 ECE Microwave Engineering
High Efficiency X-band Klystron Design Study
Update of CLIC accelerating structure design
Review Lecture Jeffrey Eldred Classical Mechanics and Electromagnetism
Few Slides from RF Deflector Developments and Applications at SLAC
Case study 6 Properties and test of a Superconducting RF cavity
CEPC Main Ring Cavity Design with HOM Couplers
Progress in the design of a damped an
Physics Design on Injector I
Coherent Synchrotron Radiation Study
Electromagnetic Waves
Parameters Changed in New MEIC Design
PH0101 Unit 2 Lecture 4 Wave guide Basic features
Presentation transcript:

Low Energy and Low Current S-Band Traveling Wave Electron Linear Accelerator structure design Hamed Shaker School of Particles and Accelerators Institute for Research in Fundamental Science

Layout Continues electron beam from Electron Gun. 45 KeV, 4 mA Pre-Buncher WR-284 waveguide Input Coupler Buncher Accelerating Tube Output Coupler Coils Water pipes Drift Length: Needed for the best bunching after the pre-buncher Power from RF source : 2 MW To the absorbing load for the remaining power To the Target: 8.2 (11.0) MeV for 2(3) Accelerating Tubes 2

Electric field for Acceleration There is no force along the direction of velocity. Magnetic field can not change the particle energy. The electric field component, parallel to velocity can change the particle energy. Magnetic field is used for bending/focusing/chromatic ity correction/…. Electric field is used for accelerating/deflecting/…. Lorentz Force 3

Radio Frequency Electromagnetic wave for acceleration SLAC virtual visit site For non-ultra relativistic electrons choosing the correct side(-90-0 degree) needs for bunching. For ultra relativistic electrons, on time particles should be on crest (-90 degree) for maximum energy gain but for minimum energy spread it is better to resonance around the crest within the bunch. 4

Dispersion diagram for uniform cross section waveguide 1- Phase velocity > c and group velocity < c (In vacuum) 2- There is lower limit for frequency (Cutoff frequency) 3- There is no upper limit for frequency 4- The axis values in graph are for internal radius = cm for cylindrical cavity in TM 01 mode 5 Eigenvalues of the waveguide calculated by Maxwell equations and boundary conditions. Classical Electrodynamics, J. D. Jackson

Rectangular and Circular Waveguide Boundary conditions for high conductivity materials Rectangular waveguide for TE(mn) mode Circular waveguide for TM(mn) mode nmnm Fields in TM 01 mode for Circular Waveguide 6

Rectangular and Circular Waveguide - II Medical electron accelerators, C. J. Karzmark, McGraw Hill, Inc p

Periodic structure – A kind of slow-wave structure dd b a d 1- Phase velocity could be < c and group velocity in our case is around 0.01c (In vacuum) 2- There is lower limit for frequency (Cutoff frequency) 3- There is upper limit for frequency 4- The axis values in graph are for b = cm for cylindrical cavity in TM01 mode and d=2.5 cm,ηd=0.5 cm and a=1 cm MHz MHz MHz For TM11 mode : MHz 8

Analytical method Methodb By Superfish code mm E. L. Chu method mm J. Gao method mm E. L. Chu Method J. Gao Method In this method, the system is assumed as a serial cavities in TM 010 mode that each of them are perturbed by two holes on both sides on the symmetrical axis. In this method, these two holes can be replaced by two electric dipoles which el electric dipole moment is 2εa 3 E 0 /3. Direct using of Maxwell equations and boundary conditions by d<<λ 0 assumption. 9

Superfish SW simulation Old design * New design a (Hole radius) 0.99  0.001cm1  cm b (Internal radius)  cm3.925  cm d (Disk space) 2.47  cm2.5  cm (Disk thickness)  d0.584  cm0.5  cm  β w (Phase velocity/c) f (Resonant frequency) MHz MHz Q (Quality Factor) r/Q Ohm Ohm T (Transit Time Factor) W (Stored energy) J J *" طراحی و ساخت کاواک شتابگر خطی الکترون " ، سیامک ناظمی، پایان نامه کارشناسی ارشد،شهریور 87 ،دانشگاه شهید بهشتی 10

Electric Field analysis - Harmonics Harmonics Coefficient MV/m a0a a a1a a a2a Phase velocity = -c/3 then it doesn’t contributes in acceleration but contributes in power transmission. Main Harmonic: Phase velocity = c and just this component contributes in acceleration. Electromagnetic Theory for Microwaves and Optoelectronic, Keqian Zheng, Dejie Li, chap. 7 11

Group velocity as the energy transmission velocity - I* Q=ω x stored energy/ Loss power from surface. W’ is the energy stored in unit length. For kd=π/2 Or E r (d),H φ (0)E r (3d/2),H φ (d/2) P SW (W) W' SW (J) P TW (W) (=P SW /4)26462 (=P SW /2) W' TW = W' SW /2 (J) v g = P TW / W' TW (m/s) v g /c α (1/m) Field attenuation after 60cm Field attenuation after 120cm V/V 0 ( After 60cm)0.929 V/V 0 (After 120cm) P/P 0 (After 60cm) P/P 0 (After 120cm) * Computer Calculations of Travelling Wave Periodic Structure Properties,SLAC-PUB-2295,March

Group velocity as dω/dk - II Mode kdk (1/m)f(MHz) ω=2  f (Hz) E+10 1/4*  E+10 2/4*  E+10 3/4*  E+10  E+10 At kd =π/2 : v g /c= By finding the resonant frequency for each mode in the Superfish model we can calculate the group velocity. 13

Accelerating Tube after construction 14

Group Velocity Measurement Mode kdk (1/m)f(MHz) ω=2  f (Hz) 3/7*  E+10 4/7*  E+10 11/24*  E+10 12/24*  E+10 Methods Group velocity J. Gao method0.0134c Field analysis method0.0116c Resonant frequency method0.0114c Measurement - I0.0099c Measurement - II0.011c Good Achievement 15

Frequency Quality factor measurement In this measurement we have a weak coupling (β<<1) then Q 0 ≈Q L = 11100±500 ≈ It means that structure is close to nominal case. Good Achievement This frequency is 0.8 MHz more than nominal case ( MHz) but the nominal case is for vacuum and 25° C. This measurement is done at air and around 15° C. 16

Energy gain reduction because of machining errors 17 By changing the phase entrance this value will be reduced to about 3% then the total reduction is about 3%+4.6%≈8%. By tuning we can avoid this (See last slide). Energy gain reduction because of random errors come from machining limitation accuracy for δq=10μm accuracy. Energy gain reduction because of systematic error comes from coupling between cells because they use the same tube SLAC Mark III paper

Buncher Inside the buncher, phase velocity increases smoothly to reach to the velocity of light. After choosing phase velocity inside the buncher, the accelerating field (without loss)is calculated using this equation. The disk hole radius(a) is equal to mm. With power loss Without power loss 18

Beam Dynamics study End of the Buncher End of the 1 st Tube End of the 2 nd Tube End of the 3 rd Tube ±7.54 deg (final distribution) ≈ 4.2 mm bunch length Capturing: -142 … 102 : 244 deg (68%) Continues beam is entered: No pre-buncher is assumed. 19 Look at slide 4

Beam Dynamics study - II End of the Buncher End of the 1 st Tube End of the 2 nd Tube End of the 3 rd Tube 20 Final Kinetic Energy: 11.04±0.26 MeV or 2.3% Energy Spread

Final Design 21 a i =10mm ηd i =5mm d i =β w,i x25 mm b i is calculated using E. L. Chu equation (See slide 9). These values is corrected finally by Superfish code. d1d1 a1a1 a2a2 b1b1 b2b2 d2d2

Buncher after construction without disks 22

Buncher after construction 23

Magnetic field needed for focusing 24 SLAC Mark III paper This field is produced by coils around the buncher. After the buncher, the electrons velocity Reach to the velocity of light then the electric field and magnetic field inside the bunch cancel each other and no magnetic field is needed for focusing. If the input power reaches to 8 MW, the magnetic field is needed is 1.4 times more.

Water cooling 25 For 2 MW peak power and the pulse length (τ p ) equal to 6 μs and 50 Hz repetition rate, the average power is equal to 600 W. Then by these equations 143 cc/s water flow is needed to keep temperature less than 1 degree (δT=1° C) more than the nominal temperature. If you remember, from slide 18, 700 KW power, leaves the structure from output coupler then just 1.3 MW power is absorbed by structure then about 93 cc/s water flow is enough. For higher input power, for example 8MW, we need 4 times more water flow (about 370 cc/s). Frequency change because of temperature changing

Pre buncher - I 26 Pre Buncher is one SW cell. Non-relativistic particles traverse it at different time see different electric field and after the pre- buncher they have different energy gain in a sinusoidal form. The drift length after the pre buncher is needed for the bunching. During traveling the drift space, particles have time to go closer to zero-crossing. R=2 in close to nominal case. U c is the maximum energy gain inside the pre buncher and U 0 is the initial energy of particles before entering the pre buncher.

Pre Buncher - II ±6.62 deg (final distribution) ≈ 3.7 mm bunch length Capturing: -162 … 167 : 329 deg (91%) in comparison with 67% without prebuncher Continues beam is entered to the pre-buncher and bunching beam is entered to the buncher. For simplicity, before the buncher, the phase of pre buncher zero crossing particle is subtracted from other particles. But for correction the entrance phase to the buncher is added to all of them. Drift length is equal to 40 cm and U c =4.6 KV in this example. The phase of pre- buncher should be about 85° for the optimum result. Pre buncher does the initial bunching to put the particles in the catching range of the buncher.

Pre Buncher - III 28 Final Kinetic Energy: 10.97±0.19 MeV or 1.7% Energy Spread in comparison with 2.3% without prebuncher.

Pre Buncher Design - I 29

Pre Buncher Design - II 30 Then a low power is needed for the pre bunching. I think a 100 W input power is good in practice.

Pre Buncher Design - III 31

Couplers 32 RcRc LsLs LcLc WR mm 2 mm RpRp 2.5 mm 2 mm We should find optimum R c and L s to reach to the minimum reflection from input coupler and to have pure traveling wave inside the structure as much as possible for our working frequency ( MHz). R p is equal to 7.5 mm/10 mm and L c is equal to 9 mm/20 mm for the input/output coupler. The nose cone that is shown on the left is just for the input coupler to avoid the SW fields for the first half of the coupler cell.

First Method for Cavity Tuning 33 “A Quantitative Method of Coupler Cavity Tuning and Simulation”, S. Zheng, Y. Cui, H. Chen, L. Xiao, PAC 2001 In this method the coupler and the first joined cell is detuned afterward by an external conductor object and the reflection angles are measured for two different frequencies near our working frequency ( MHz). By using these equations, the resonant frequency of coupler cell (ω c ) and the coupling coefficient (β) between the coupler cell and the waveguide are calculated. φ 1,2 is equal to the difference between reflection angles for the first joined detuned and the coupler cell detuned cases for each chosen frequency.

Second Method for Cavity Tuning 34 D. Alesini et al., “Design of couplers for traveling wave RF structures using 3D electromagnetic codes in the frequency domain”, Nucl. Instrum. Methods A, June 2007, 580 (2007), p In this method, the difference between reflection angles is measured when a conductor plate is placed at the middle of the different joined cells. The coupler is matched when the reflection angles difference for the working frequency is 180° (2 x 90°) for moving the plate by one cell.

Tuning result 35 Coupler/MethodRCRC LsLs Input / mm28.4 mm Input / 2 (89.1°,87.2°)34.81 mm28.5 mm Input / Final34.81 mm28.3 mm Output / mm26.55 mm Output / 2 (89.4°,81.6°) mm26.55 mm Output / Final38.61 mm26.4 mm

Input Coupler Simulation 36

Output Coupler Simulation 37

Coupler Design 38

Coupler after Construction 39

Couplers attached to the Buncher and Tube 40

Tuning 41 Slater’s equation This equation shows how resonant frequency of a cavity changes if we have a small stored energy perturbation. We can assume for small deformation on the outer wall the stored energy is decreased equal to energy stored in this volume before perturbation. δV is the volume of deforming. This method, deforming, can be used for tuning the phase advance of each cell then the energy gain reduction can be avoided. For deforming, one or more holes are drilled around each cell to reach close to inner surface of cell (about 2 mm). If we have 4 holes for each cell with 12 mm diameter, it just need a 1 mm deforming depth for 3 MHz frequency tuning. Deforming depth Deforming hole diameter

References 42 [1] E. L. Chu and W. W. Hansen, “The Theory of Disk Loaded Wave Guides”, J. Appl. Physics, November 1947, Vol. 18, p [2] J. Gao, “Analytical Approach and Scaling Laws in the Design of Disk-Loaded Travelling Wave Accelerating Structures”, Particle Accelerators, 1994, Vol. 43(4), p [3] S. Zheng et al., “A Quantitative Method of Coupler Cavity Tuning and Simulation”, PAC01 Proceedings, June 2001, p ; [4] D. Alesini et al., “Design of couplers for traveling wave RF structures using 3D electromagnetic codes in the frequency domain”, Nucl. Instrum. Methods A, June 2007, 580 (2007), p [5] M. Chodorow et al., “Stanford High-Energy Linear Electron Accelerator(Mark III)”, Rev. Sci. Instrum., February 1955, Vol. 26(2), p [6] G. A. Loew et al., “Computer Calculations of Travelling Wave Periodic Structure Properties”, SLAC-PUB-2295, March 1979 (A). [7] J. Haimson, “Electron Bunching in Traveling Wave Linear Accelerators”, Nucl. Instrum. Methods, January 1966, Vol. 39(1), p

Thanks for your attention 43