Training materials for wireless trainers Fundamentals of telecommunications.

Slides:



Advertisements
Similar presentations
Physical Layer: Signals, Capacity, and Coding
Advertisements

Signal Encoding Techniques
EP301 COMPUTER NETWORKING SYSTEM
Analog Communications
Chapter : Digital Modulation 4.2 : Digital Transmission
Digital Coding of Analog Signal Prepared By: Amit Degada Teaching Assistant Electronics Engineering Department, Sardar Vallabhbhai National Institute of.
Chapter 5 – Signal Encoding and Modulation Techniques
Eeng 360 Communication Systems I Course Information
ECE 4321: Computer Networks Chapter 3 Data Transmission.
Modulation of Digital Data 1.Digital-to-Analog Conversion 2.Amplitude Shift Keying (ASK) 3.Frequency Shift Keying (FSK) 4.Phase Shift Keying (PSK) 5.Quadrature.
Computer Communication & Networks Lecture # 06 Physical Layer: Analog Transmission Nadeem Majeed Choudhary
Digital to Analog Many carrier facilities are analog Many transmission media are also analog (microwave, radio) We can carry digital values over analog.
EE302 Lesson 21: Transmission of Binary Data in Communication Systems
Transmission Basics ITNW 1325, Chapter III. OSI Physical Layer.
DIGITAL COMMUNICATIONS.  The modern world is dependent on digital communications.  Radio, television and telephone systems were essentially analog in.
TRANSMISSION FUNDAMENTALS Review
Introduction to Wireless Communications. Wireless Comes of Age Guglielmo Marconi invented the wireless telegraph in 1896 Communication by encoding alphanumeric.
Digital Data Transmission ECE 457 Spring Information Representation Communication systems convert information into a form suitable for transmission.
Chapter 3 Data and Signals
© Kemal AkkayaWireless & Network Security 1 Department of Computer Science Southern Illinois University Carbondale CS591 – Wireless & Network Security.
Department of Electronic Engineering City University of Hong Kong EE3900 Computer Networks Data Transmission Slide 1 Continuous & Discrete Signals.
IS250 Spring 2010 Physical Layer IS250 Spring 2010
William Stallings Data and Computer Communications 7th Edition (Selected slides used for lectures at Bina Nusantara University) Data, Signal.
Module 3.0: Data Transmission
Modulation                                                                 Digital data can be transmitted via an analog carrier signal by modulating one.
Lecture 3 Data Encoding and Signal Modulation
Copyright © 2003, Dr. Dharma P. Agrawal and Dr. Qing-An Zeng. All rights reserved. 1 Chapter 7 Multiple Division Techniques.
Modulation Modulation => Converts from digital to analog signal.
IT-101 Section 001 Lecture #15 Introduction to Information Technology.
Modulation and Demodulation
1 Computer Communication & Networks Lecture 5 Physical Layer: Data & Signals Waleed Ejaz
Digital to analogue conversion. 1 DIGITAL-TO-ANALOG CONVERSION Digital-to-analog conversion is the process of changing one of the characteristics (A,
Chapter 2 Basic Communication Theory Basic Communications Theory w Understand the basic transmission theory, and figure out the maximum data rate. w.
McGraw-Hill©The McGraw-Hill Companies, Inc., 2001 Data Transmission Techniques Data to be transmitted is of two types 1.Analog data 2.Digital data Therefore,
Review: The application layer. –Network Applications see the network as the abstract provided by the transport layer: Logical full mesh among network end-points.
Lecture 3-1: Coding and Error Control
1 Business Telecommunications Data and Computer Communications Chapter 3 Data Transmission.
1 Ch 6 Long-Distance Communication Carriers, Modulation, and Modems.
CE 4228 Data Communications and Networking
Data Transmission The basics of media, signals, bits, carries, and modems (Part III)
Chi-Cheng Lin, Winona State University CS 313 Introduction to Computer Networking & Telecommunication Modulation, Multiplexing, & Public Switched Telephone.
Coding No. 1  Seattle Pacific University Modulation Kevin Bolding Electrical Engineering Seattle Pacific University.
COMMUNICATION TECHNOLOGY by Shashi Bhushan School of Computer and Information Sciences.
1 CSCD 433 Network Programming Fall 2013 Lecture 4 Physical Layer Line Coding Continued.
Signal Encoding Techniques. Lecture Learning Outcomes Be able to understand, appreciate and differentiate the different signal encoding criteria available.
1 Kyung Hee University Chapter 5 Analog Transmission.
The Physical Layer Lowest layer in Network Hierarchy. Physical transmission of data. –Various flavors Copper wire, fiber optic, etc... –Physical limits.
1 Chapter 2 Fundamentals of Data and Signals Data Communications and Computer Networks: A Business User’s Approach.
CS Spring 2009 CS 414 – Multimedia Systems Design Lecture 3 – Digital Audio Representation Klara Nahrstedt Spring 2009.
Data Comm. & Networks Lecture 6 Instructor: Ibrahim Tariq.
1 Composite Signals and Fourier Series To approximate a square wave with frequency f and amplitude A, the terms of the series are as follows: Frequencies:
Topics discussed in this section:
Chapter : Digital Modulation 4.2 : Digital Transmission
Shannon’s Theorem Nyquist Theorem Modulations Multiplexing
Encoding How is information represented?. Way of looking at techniques Data Medium Digital Analog Digital Analog NRZ Manchester Differential Manchester.
1 3. Data Transmission. Prof. Sang-Jo Yoo 2 Contents  Concept and Terminology  Analog and Digital Data Transmission  Transmission Impairments  Asynchronous.
Powerpoint Templates Computer Communication & Networks Week # 04 1 Lecture only.
Eeng360 1 Eeng 360 Communication Systems I Course Information  Instructor: Huseyin Bilgekul, Room No: EE 207, Office Tel:  Course Webpage:
1587: COMMUNICATION SYSTEMS 1 Digital Signals, modulation and noise Dr. George Loukas University of Greenwich,
Lifecycle from Sound to Digital to Sound. Characteristics of Sound Amplitude Wavelength (w) Frequency ( ) Timbre Hearing: [20Hz – 20KHz] Speech: [200Hz.
Fundamentals of Communications. Communication System Transmitter: originates the signal Receiver: receives transmitted signal after it travels over the.
CHAPTER 4. OUTLINES 1. Digital Modulation Introduction Information capacity, Bits, Bit Rate, Baud, M- ary encoding ASK, FSK, PSK, QPSK, QAM 2. Digital.
Lecture 2.4. Multiplexing. Learning Outcomes Discuss the concept of Multiplexing Explain & calculate frequency-division multiplexing. Explain & calculate.
IT-101 Section 001 Lecture #15 Introduction to Information Technology.
Computer Communication & Networks
KOMUNIKASI DATA Materi Pertemuan 10.
Introduction to electronic communication systems
Bit rate Baud rate Goal in data communication is to increase the bit rate while decreasing the baud rate. Increasing the data rate increases the speed.
Introduction King Saud University
Modulation Modulation => Converts from digital to analog signal.
Presentation transcript:

Training materials for wireless trainers Fundamentals of telecommunications

2 Goals To present the basics concepts of telecommunication systems with focus on digital and wireless

3 Basic Concepts Signal Analog, Digital, Random Sampling Bandwidth Spectrum Noise Interference Channel Capacity BER Modulation Multiplexing Duplexing

4 Telecommunication Signals Telecommunication signals are variation over time of voltages, currents or light levels that carry information. For analog signals, these variations are directly proportional to some physical variable like sound, light, temperature, wind speed, etc. The information can also be transmitted by digital signals, that will have only two values, a digital one and a digital zero.

5 Telecommunication Signals Any analog signal can be converted into a digital signal by appropriately sampling it. The sampling frequency must be at least twice the maximum frequency present in the signal in order to carry all the information contained in it. Random signal are the ones that are unpredictable and can be described only by statistical means. Noise is a typical random signal, described by its mean power and frequency distribution. 5

6 Examples of Signals Random Signal AM modulated SignalFM modulated Signal

7 Sinusoidal Signal v(t)= A cos(w o t - ⊖ ) A = Amplitude, volts w o = 2πf o, angular frequency in radians f o = frequency in Hz T = period in seconds, T= 1/f o ⊖ = Phase time 0 A -A ⊖ T

8 Signals and Spectra

9 Spectral analysis and filters f1f1 f2f2 f3f3 Spectrum Analyzer Oscilloscope

10

11 Sampling Analog Signal Sampling Circuit Sampled Signal t The sampled signal can be quantized and coded to convert it to a digital signal. This is normally done with an ADC (Analog to Digital Converter). The recovery of the original signal is by means of a DAC.

12 Image Sampling

Sampling, Quantization and Coding 1 Analog Signal Samples

14 Why Digital? Noise does not accumulate when you have a chain of devices like it happens in an analog system: CD Versus Vinyl, VHS Vs DVD. The same goes for the storing of the information. Detection of a digital signal is easier than an analog signal, so digital signal can have greater range. Digital signals can use less bandwidth, as exemplified by the “digital dividend” currently being harnessed in many countries. Digital circuits are easier to design and can achieve greater integration levels than analog circuits. Digital signals can be encoded in ways that allow the recover from transmission errors, albeit at the expense of throughput.

15 Communication System

16 Signal Delay

17 Attenuation Transmitted Signal Received Signal

18 Noise in an analog Signal

19 Bandwidth Limitation

20 Interference Any signal different from the one that our system is designed to receive that is captured by the receiver impairs the communication and is called interference. Intra-channel interference originates in the same channel as our signal. Co-channel interference is due to the imperfection of the filters that will let in signals from adjacent channels. 20

21 Information Measurement I = log 2 (1/Pe) The information carried by a signal is expressed in bits and is proportional to the logarithm of the inverse of the probability of the occurrence of the corresponding event. The more unlikely an event to happen, the more information its happening will carry. Transmitting a message of an event that the receiver already knows carries no information. The amount of information transmitted in one second is the capacity of the channel, expressed in bit/s. 21

22 Redundancy Sending twice the same information is a waste of the system capacity that reduces the throughput. Nevertheless, if an error occurs, the redundancy can be used to overcome the error. Every error correcting code must use some sort of redundancy. 22

23 Channel Capacity

24 Detection of a noisy signa l

25 MoDem Analog SignalDigital Signal Mod -Dem 1 0 Transmission Medium

26 Comparison of modulation techniques 1 0 Digital Sequence ASK modulation FSK modulation PSK modulation QAM modulation, changes both amplitude and phase

27 BER Versus E b /N o From Wikipedia:

28 Comparison of modulation types BER of Mod. TypeBits/SymbolRequired E b /N o 16 PSK418 dB 16 QAM415 dB 8 PSK314.5 dB 4 PSK210.1 dB 4 QAM210.1 dB BFSK113.5 dB BPSK110.5 dB

29 Multiplexing Communication Channel A B C D A B C D A B C D Multiplexer Demultiplexer

30 Medium sharing techniques

31 Example: U.S. Television Channels Allocation frequency, MHz Channel 2 Channel 3 Channel 4 Channel 5 Channel 6 Signal Power

32 CDMA analogy Two messages superposed, one in yellow and one in blue A blue filter reveals what is written in yellow A yellow filter reveals what is written in blue

33 Types of transmissions Simplex: one way only, example: TV Broadcasting Half-duplex: the corresponding stations have to take turns to access the medium, example: walkie-talkie. Requires hand-shaking to coordinate access. This technique is called TDD (Time Division Duplexing) Full-duplex: the two corresponding stations can transmit simultaneously, employing different frequencies. This technique is called FDD (Frequency Division Duplexing). A guard band must be allowed between the two frequencies in use. 33

34 Conclusions The communication system must overcome the noise and interference to deliver a suitable replica of the signal to the receiver. The capacity of the communication channel is proportional to the bandwidth and to the logarithm of the S/N ratio. Modulation is used to adapt the signal to the channel and to allow several signals to share the same channel. Higher order modulation schemes permit higher transmission rates, but require higher S/N ratio. The channel can be shared by several uses that occupy different frequencies, different time slots or different codes

For more details about the topics presented in this lecture, please see the book Wireless Networking in the Developing World, available as a free download in many languages: For more details about the topics presented in this lecture, please see the book Wireless Networking in the Developing World, available as a free download in many languages: Thank you for your attention