Residential Plumbing Where does the water in your home come from and where does it go?

Slides:



Advertisements
Similar presentations
Plumbing.
Advertisements

Installing Your Simple Drainback Solar Hot Water System Your Simple Drainback System comes with a highly competent installation manual. Please consult.
Lesson 17 Working with Copper Tubing. Next Generation Science/Common Core Standards Addressed! n CCSS.ELA Literacy.RST.9 ‐ 10.3 Follow precisely a complex.
HVAC523 Soldering.
1 HVACR316 – Piping Tubing and Piping. 2 Purposes of Tubing and Piping Provides a path for refrigerant to take Provides a means to return oil to the compressor.
Lesson Working with Copper Tubing. Interest Approach n Why is copper tubing only used for water and fuel lines?
Student Book © 2004 Propane Education & Research CouncilPage Installing Copper Tubing in Distribution Systems Personnel who install copper.
Trade of Plumbing – Phase 2 Module 2 – Unit 6 Module 2: Domestic Hot and Cold Water Service Unit 6 – Soldering Duration – 32 Hours.
1 The Pringles Cantenna. 2 Parts List All-thread, 5 5/8″ long, 1/8″ OD (2) nylon lock nuts (5) 1″ washers, 1/8″ ID aluminum tubing, 1/4″ ID axp 8” long.
TUBING AND PIPING.
1 REFRIGERATION FUNDAMENTALS HVAC/R. 2 SOLDERING & BRAZING When and why; –When an A/C or refrigeration system is entered, it must be properly sealed –Although.
Tool Use Strip wire. Soldering Iron Step 1: Tinning the iron Tinning helps to make soldering easier and quicker while keeping the iron in good condition.
Domestic Hot and Cold Water Service
Unit 204: Common plumbing processes
Soldering Basics. Ground rules for soldering Rule 1: Irons get hot. Be safe. Rule 2: You need to wet your sponge. This wet sponge is used to clean the.
New Mexico FFA Agricultural Mechanics Career Development Event Plumbing.
1 Chelmsford Amateur Radio Society Intermediate Licence Course Carl Thomson G3PEM Slide Set 12: v Jun-2007 (10) Soldering Chelmsford Amateur Radio.
Intermediate Course (10) Soldering Karl Davies East Kent Radio Society EKRS 1.
 Desired metal: U se a length of metal that matches your desired ring size + a little extra for sanding away.  Silver solder Y ou need a piece of silver.
Plated Through Hole Soldering Materials by Lindsay Craig.
Project # 2 Ring bands. Soldering Filing texture stamping cleaning Annealing sanding Bending Polishing/sandblasting.
Sterling Practices in Designing and Scoring Performance-Based Exams Ronald C. Rodgers, Ph.D. Continental Testing Services, Inc./ Employment Research Institute.
1 Chelmsford Amateur Radio Society Intermediate Licence Course Carl Thomson G3PEM Slide Set 12 (10) Soldering Chelmsford Amateur Radio Society Intermediate.
Plumbing Plastic Pipe Plumbing Systems 20091Plumbing.
Unit 7: Tubing And Piping
Copper Pipe Plumbing Systems
Residential and Commercial Plumbing Mr. Lemmons Ag Mechanics.
NGfL CYMRU GCaD PLUMBING MATERIALS, PIPE BENDING AND PRESSURE TESTING.
Objectives Offer a reliable, flameless joining system to reduce time and cost of joining copper tubing Keep the professional tradesman’s preferred plumbing.
Introduction to Plumbing Date. Bellwork 0 Fill out your KWL sheet about plumbing 0 What do you K now about plumbing? 0 What do you W ant to learn about.
Handout from Clinic Conducted by Bernard Kempinski at several NMRA conventions
WHAT IS SOLDERING? Soldering is the process of joining metal leads, creating a mechanical and electrical bond.
1 HVACR316 - Piping Soldering. 2 Soldering Copper Tubing The most common method of joining copper tubing in hydronic heating systems is soft soldering.
Plumbing Introduction 2009 Plumbing.
Basic Home Plumbing.
1 HVACR316 - Piping Torches, Tips, Tanks Torches, Tips, Tanks.
Plumbing Theory. DWV System The DWV Drain-waste- vent system in plumbing a system that removes sewage and greywater from the house/building and it also.
1 HVACR316 - Piping Fundamentals of Refrigeration Soldering and Brazing Fundamentals of Refrigeration Soldering and Brazing.
Plumbing Tools ˚ Pipe Elbow 45˚ Pipe Elbow Making a 45 degree turn with a pipe.
Unit 35 Plumbing Objective To identify plumbing materials and perform basic plumbing procedures.
Plumbing Introduction to Ag Mechanics MSAGED 7-6 Written by Melissa Moulton.
CON 4003/CVE 4073/CVE 5073 Construction Estimating Prof R. V. Locurcio.
Creating a Sun Catcher. Choose a Pattern For this project, you will need to choose a pattern from my Sun Catcher collection for Glass Eye. You will find.
Copyright © 2010 Delmar, Cengage Learning. ALL RIGHTS RESERVED. Unit 13 Fastening Metal.
Copper Pipe Plumbing Systems
SECTION 2 SAFETY, TOOLS AND EQUIPMENT, SHOP PRACTICES UNIT 7: TUBING AND PIPING.
From foukeffa.org Written by Dale Conrady Edited by Danell Woolery Plumbing.
Plumbing Unit. Purpose: Transporting liquids safely from one point to another for storage, processing, and direct use Carries fresh water from a source.
PLUMBING PARTS Plumbing ensures that a royal flush always beats a full house.
Plumbing by Dale Conrady.
Soldering Brazing.
Introduction to Soldering
Soldering PCBs – Siren Kit Week 1 of 2
Written by Dale Conrady
Introduction to Soldering (PCB Bread boards)
Now What? Forgot to Pull a Permit?
Copper Soldering Technique
Unit 13 Ag Mechanics Fastening metal.
Fault detection Lecture (1).
Fluxes Veerankutty ME S4 NO: 56.
Starter for today A newly discovered planet has been deemed inhabitable. You have been given the assignment to design a travel poster to bring tourists.
Plumbing.
Plumbing Unit.
SAFETY, TOOLS AND EQUIPMENT, SHOP PRACTICES
PLUMBING MATERIALS, PIPE BENDING AND PRESSURE TESTING
How to Stay Away from Lead
By Gerry Crenshaw WD4BIS
Presentation transcript:

Residential Plumbing

Where does the water in your home come from and where does it go?

Let’s start with where does it come FROM?

So WHERE does it go after we are DONE with it?

With Regards to PLUMBING, How Does Water Travel?

PIPES

Tubing

What’s the DIFFERENCE

How they are MEASURED Pipe Tube

In residential plumbing:

Tubing (typically) brings water TO the residence

Piping (typically) takes water AWAY from the residence

Other Plumbing BITS

Soldering Copper Pipe

Tools Required

Steps to an effective Solder Joint

Measure Cut Layout Step 1:

Clean the OXIDATION off of the outside of the pipe Step 2:

Clean the inside of the FITTINGS Step 3:

Apply FLUX to all joining surfaces Step 4:

Step 5: Assemble and apply solder

Step 6: Wipe Joint with a wet rag

Step 6: Wipe Joint with a wet rag