READING QUIZ In the analysis of a planar truss, all the member are assumed to be ___________. A) three-force member B) zero-force member C) two-force member.

Slides:



Advertisements
Similar presentations
Copyright © 2010 Pearson Education South Asia Pte Ltd
Advertisements

Proof that the medians of any triangle intersect at a single point.
The Howe Bridge truss is subjected to the loading shown
EXAMPLE 4 Prove the Converse of the Hinge Theorem
Trusses.
CE Statics Chapter 6 – Lecture 20. THE METHOD OF JOINTS All joints are in equilibrium since the truss is in equilibrium. The method of joints is.
Geometry Review Are you ready for the test !!!!!! 6 th Grade Graham Park Middle School Feb 2013.
PREPARED BY : NOR AZAH BINTI AZIZ KOLEJ MATRIKULASI TEKNIKAL KEDAH
ENGR-1100 Introduction to Engineering Analysis
CE Statics Chapter 6 – Lecture 19.
READING QUIZ Frames are generally ________ and are used to ______ loads. A) stationary; transmit B) moving; support C) stationary; support D) moving; transmit.
ATTENTION QUIZ Forces F1 , F2 and F3 are acting on a particle in static equilibrium. If F1 = {F1X i + 3j – 4k} N, F2 = {– i + F2Y j +
TRUSSES–THE METHOD OF SECTIONS (Section 6.4)
ME221Lecture 281 ME 221 Statics Lecture #28 Sections 6.1 – 6.4.
READING QUIZ The resultant force of a given couple system is always _______. A) positive B) negative C) zero D) None of the above.
EGR 280 Mechanics 4 – Analysis of Structures Trusses.
ME221Lecture 151 ME 221 Statics Lecture #15b Sections 6.1 – 6.4.
More Truss Analysis Problems
ENGR-1100 Introduction to Engineering Analysis
B) it can be used to solve indeterminate trusses
TRUSSES – METHODS OF JOINTS
EGR 106 – Project Description (cont.) Analysis of truss structures A simple example Factor of Safety calculations This week’s assignment.
 The factorial function (n!)  Permutations  Combinations.
Parallel Lines and Proportional Parts By: Jacob Begay.
To Play: Pick a topic column Pick a point value Be the first to buzz in the correct answer!
SIMPLE TRUSSES, THE METHOD OF JOINTS, & ZERO-FORCE MEMBERS
SIMPLE TRUSSES, THE METHOD OF JOINTS, & ZERO-FORCE MEMBERS
Chapter 4 sections 1 and 2.  Fig. 1  Not connected  All vertices are even.  Fig. 2  Connected  All vertices are even.
SIMPLE TRUSSES, THE METHOD OF JOINTS, & ZERO-FORCE MEMBERS
Chapter 6: Structural Analysis
Engineering Mechanics: Statics
ENGINEERING MECHANICS STATICS & DYNAMICS
1.4 and 1.5 Quiz on Friday!. When two lines intersect, they intersect in a ___________ Point.
SIMPLE TRUSSES, THE METHOD OF JOINTS, & ZERO-FORCE MEMBERS
WORKSHEET 6 TRUSSES. Q1 When would we use a truss? (a) long spans, loads not too heavy (b) when want to save weight (d) when want light appearance (c)
ERT146 QIUZ 1 ANSWERS.
Objective: Students will use proportional parts of triangles and divide a segment into parts. S. Calahan 2008.
READING QUIZ Answers: 1.D 2.A
THE METHOD OF SECTIONS In-Class Activities: Check Homework, if any Reading Quiz Applications Method of Sections Concept Quiz Group Problem Solving Attention.
Problem kN 12.5 kN 12.5 kN 12.5 kN Using the method of joints, determine the force in each member of the truss shown. 2 m 2 m 2 m A B C D 2.5.
By Meli & Amy & Meggie & Bex. What is route inspection hmmmm??? Objective: Is to go along every single edge and end up back to where you started from.
 If three sides of one triangle are congruent to the three sides of another triangle, then the two triangles are congruent.  If AB = DE, BC = EF, AC.
ENGINEERING MECHANICS (15BS105)
Do Now: 1. Name how the two triangles are congruent in the rectangle below: 2. Find the measure of an exterior angle in a pentagon: Homework: Packet page.
The graph is neither Eulerian or Semi – Eulerian as it has 4 ODD vertices.
Station 1 – Provide a justification (definition, property, postulate, or theorem) for each statement. D 1.) If BH ^ DC, then ÐDCH is a right angle. 2.)
100 ABCD is a Square. 1) m<3 = _____ 2) If AC = 10, DE = _____
6.2 Properties of Parallelograms
THE METHOD OF SECTIONS Today’s Objectives: Students will be able to
PROPORTIONAL SEGMENTS & BASIC SIMILARITY THEOREM
Jan 2007.
Combinations COURSE 3 LESSON 11-3
Set up ratios: = = Fill in ratios: Solve the proportion: =
Check It Out! Example 1 Write an indirect proof that a triangle cannot have two right angles. Step 1 Identify the conjecture to be proven. Given: A triangle’s.
1.5 Segments & Their Measures
Structure I Course Code: ARCH 208
TRUSSES SAMPLE QUESTIONS.
AB AC AD AE AF 5 ways If you used AB, then, there would be 4 remaining ODD vertices (C, D, E and F) CD CE CF 3 ways If you used CD, then, there.
Analysis of truss-Method of Joint
SIMPLE TRUSSES, THE METHOD OF JOINTS, & ZERO-FORCE MEMBERS
TRUSSES – METHODS OF JOINTS
THE METHOD OF SECTIONS Today’s Objectives:
ISOMETRIC PROJECTION BISECT LINE TO GET RED DOT. Down 80 In 70
#17 PA8 Sem2 Practice Exam A #17 PA8 Sem2 Practice Exam B
Structure Analysis II.
Kruskal’s Algorithm AQR.
Determine whether {image} is convergent or divergent.
SIMPLE TRUSSES, THE METHOD OF JOINTS, & ZERO-FORCE MEMBERS
Truss analysis.
1.3 Segments & their Measures
Presentation transcript:

READING QUIZ In the analysis of a planar truss, all the member are assumed to be ___________. A) three-force member B) zero-force member C) two-force member D) None of the above.

READING QUIZ The simplest form of a planar truss is a _______. A) rectangle B) triangle C) trapezoid D) v-shaped

CONCEPT QUIZ Select the true statement about the truss shown. A) F CE is tensile B) F DE is tensile C) F CD = F CB D) F AB = F BC P P P D E F GA B C

CONCEPT QUIZ For the truss shown, what is F AB ? A) 1000 N Tension B) 1000 N Compression C) 1330 N Tension D) 1330 N Compression 1600 N BC A

ATTENTION QUIZ In the truss shown, select the zero-force members. A) CG B) BH, BG, DG and DF C) BC, CG, CD D) AH, HG, EF, FG A B C D HG F P E

ATTENTION QUIZ For the following truss, what is F BD ? A) P - Tension B) P - Compression C) 2P - Tension D) 2P - Compression P B D P AC