Forging new generations of engineers. Tensile Test Report Graphical Analysis and Computational Results of Collected Data.

Slides:

Advertisements

Similar presentations

2E4: SOLIDS & STRUCTURES Lecture 9

Advertisements

Material testing Lesson 2.

Edexcel AS Physics Unit 1 : Chapter 7: Solid Materials

MECHANICAL PROPERTIES

Forging new generations of engineers. The following MATERIAL PROPERTIES can be evaluated / determined by TENSILE TESTING: STRENGTH DUCTILITY ELASTICITY.

Elasticity by Ibrhim AlMohimeed

Solid Materials.

Chapter 11 Mechanical Properties of Materials

LECTURER 2 Engineering and True Stress-Strain Diagrams

Normal Strain and Stress

Chapter 3 Mechanical Properties of Materials

The various engineering and true stress-strain properties obtainable from a tension test are summarized by the categorized listing of Table 1.1. Note that.

EXPERIMENT # 3 Instructor: M.Yaqub

CTC / MTC 222 Strength of Materials

Tensile Test The most common static test is the uniaxial tensile test, which provides information about a variety of properties. As a load is applied to.

Mechanical Properties of

Lecture 26: Mechanical Properties I: Metals & Ceramics

ENGR 225 Section

Deforming Solids.

Mechanics of Elastic Materials

Elastic Stress-Strain Relationships

CHAPTER OBJECTIVES Show relationship of stress and strain using experimental methods to determine stress-strain diagram of a specific material Discuss.

Elasticity and Strength of Materials

Mechanical Properties

Objectives Students will be able to label a stress-strain diagram correctly indicating. Ultimate stress, yield stress and proportional limit. Students.

CHE 333 Class 11 Mechanical Behavior of Materials.

Class #1.2 Civil Engineering Materials – CIVE 2110

ELASTICITY. Elasticity  Elasticity is a branch of Solid mechanics that deals with the elastic behavior of solids. It is the property of material of a.

Unit V Lecturer11 LECTURE-I  Introduction  Some important definitions  Stress-strain relation for different engineering materials.

STRUCTURES Outcome 3 Gary Plimer 2008 MUSSELBURGH GRAMMAR SCHOOL.

Mechanical Properties of Materials

Materials PHYA2. MATERIALS DENSITY, SPRINGS, STRESS AND STRAIN Topics 11, pp.162–173.

1 ME383 Modern Manufacturing Practices Lecture Note #3 Stress-Strain & Yield Criteria Dr. Y.B. Guo Mechanical Engineering The University of Alabama.

CTC 422 Design of Steel Structures Introduction. Steel as a Building Material Advantages High strength / weight ratio Properties are homogeneous and predictable.

Poisson's ratio, n • Poisson's ratio, n: Units:

Chapter 2 Properties of Metals.

Mechanical Properties of Materials

1.To understand the keywords associated with the deformation of different types of solids 2.To be able to calculate stress, strain and hence Young’s modulus.

1.To understand the keywords associated with the deformation of different types of solids 2.To be able to calculate stress, strain and hence Young’s modulus.

Unit 1 Key Facts- Materials Hooke’s Law Force extension graph Elastic energy Young’s Modulus Properties of materials.

Haseeb Ullah Khan Jatoi Department of Chemical Engineering UET Lahore.

Group 2 presentation Q : stress and strain curve presentation.

STRUCTURES Young’s Modulus. Tests There are 4 tests that you can do to a material There are 4 tests that you can do to a material 1 tensile This is where.

SIMPLE STRESS & STRAIN ► EN NO GUIDED BY EN NO PROF. V.R.SHARMA GEC PALANPUR APPLIED MECHANICS DEPARTMENT.

PROPERTIES OF MATERIALS ENF 150 Chapter 10: Properties of Materials.

The various engineering and true stress-strain properties obtainable from a tension test are summarized by the categorized listing of Table 1.1. Note that.

Material Testing under Tension

CHAPTER OBJECTIVES Show relationship of stress and strain using experimental methods to determine stress-strain diagram of a specific material Discuss.

Mechanics of Materials

Introduction We select materials for many components and applications by matching the properties of the material to the service condition required of the.

Dr. Omar S.M.J.Ali PhD Orthodontic

MECHANICAL PROPERTIES OF MATERIALS

Chapter 3 Mechanical Properties of Materials

Poisons Ratio Poisons ratio = . w0 w Usually poisons ratio ranges from

Experiment #1 Tension Test

Forging new generations of engineers

Forging new generations of engineers

Tensile Testing The following MATERIAL PROPERTIES can be evaluated / determined by TENSILE TESTING: STRENGTH DUCTILITY ELASTICITY STIFFNESS.

Material Testing.

Mechanical Properties: 1

Applied Technology High School (ATHS)

Elastic & Plastic behavior of Materials….(Contd)

Elastic & Plastic behavior of Materials

Mechanical properties of metals Stress and Strain in metals

PDT 153 Materials Structure And Properties

LECTURER 2 Engineering and True Stress-Strain Diagrams

Describing deformation

Mechanical Properties Of Metals - I

Mechanical Property 기계적 성질

Presentation transcript:

Forging new generations of engineers

Tensile Test Report Graphical Analysis and Computational Results of Collected Data

Tensile Report Layout Your Tensile report will include 10 pages which will contain the following information: Title page Statistical Process Control Data collected from tensile data Proportional Strength - Definition-graph-calculation Yield Strength - Definition-graph-calculation Tensile or Ultimate Strength - Definition-graph-calculation Breaking/Rupture Strength - Definition-graph-calculation Modulus of Elasticity - Definition-graph-calculation Modulus of Resilience - Definition-graph-calculation Modulus of Toughness - Definition-graph-calculation Calculations Page - data not needing graphical representation

Title Page Major Topic Heading Course Name Topic of Paper Student Name Instructor Date Period

Statistical Process Control Data Cut SPC data sheet into sections and glue to titled page Break information into appropriate sections. e.g. Recorded Data Results Histogram Statistical Process Control Aluminum Data

Proportional Limit Stress Proportional Limit - The greatest stress a material is capable of withstanding without deviation from a straight -line proportionality between stress and strain. If the force applied to the material is released the material will return to it’s original shape and size. Calculation S = F / A Graph

Yield Point Stress Yield point - The point at which a sudden elongation takes place, while the load on the sample remains the same or actually drops. If the force applied to the material is released the material will not return to it’s original shape and size. Calculation S = F / A Graph

Ultimate or Tensile Stress Ultimate Strength - The point at which the maximum load for a sample is achieved. Beyond this point, elongation of the sample continues but the force being exerted decreases. Calculation S = F / A Graph

Breaking/Rupture Stress Breaking/Rupture Stress - The maximum amount of stress that can be applied before rupture occurs. The material fractures in the necking region where the material reduces in diameter as the material elongates. Calculation S = F / A Graph

Modulus of Elasticity Modulus of Elasticity -A measure of a materials ability to regain its original dimensions after the removal of a load or force. The modulus is the slope of the straight line portion of the stress-strain diagram up to the proportional limit. Calculation E = (F 1 -F 2 )L o / (  1 -  2 )A Graph

Modulus of Resilience Modulus of Resilience -A measure of a materials ability to absorb energy up to the elastic limit. This modulus is represented by the area under the stress versus strain curve from zero force to the elastic limit. Calculation Ur = 1/2 (  yp )(  yp ) Graph Elastic Limit

Modulus of Toughness Modulus of Toughness -A measure of a materials ability to plastically deform without fracturing. Work is performed by the material absorbing energy by the blow or deformation. This measurement is equal to the area under the stress versus strain curve from its origin through the rupture point. Graph Calculation: U t = 1/3(  Br ) (  yp + 2  ult )

Calculation Page Total Strain/ Deformation -The total amount of elongation of a sample to rupture normalized(divided by) by the initial length. Calculation:   total =  total /L o Ductility:The ability of a material to be deformed plastically without rupture. Calculation: % Elongation =  total (100) Ductility:The ability of a material to be deformed plastically without rupture. Calculations: % Reduction in area = A original - A final / A original (100)