UNIT 3: Energy Changes and Rates of Reaction Chapter 5: Energy Changes Chapter 6: Rates of Reaction

Chapter 6: Rates of Reaction UNIT 3 Chapter 6: Rates of Reaction Chapter 6: Rates of Reaction An important part of studying chemical reactions is to monitor the speed at which they occur. Chemists look at how quickly, or slowly, reactions take place and how these rates of reaction are affected by different factors. Image source: MHR, Chemistry 12 © 2011. ISBN 07-106010-3; page 276 The light produced by a firefly depends on the speed of a particular chemical reaction that occurs in its abdomen. TO PREVIOUS SLIDE

6.1 Chemical Reaction Rates UNIT 3 Chapter 6: Rates of Reaction Section 6.1 6.1 Chemical Reaction Rates Chemical kinetics is the study of the rate at which chemical reactions occur. The term reaction rate, or rate of reaction refers to: the speed that a chemical reaction occurs at, or the change in amount of reactants consumed or products formed over a specific time interval TO PREVIOUS SLIDE

Determining Reaction Rates UNIT 3 Chapter 6: Rates of Reaction Section 6.1 Determining Reaction Rates The reaction rate is often given in terms of the change in concentration of a reactant or product per unit of time. Image source: MHR, Chemistry 12 © 2011. ISBN 07-106010-3; page 354, Table 6.1 The change in concentration of reactant A was monitored over time. TO PREVIOUS SLIDE

Determining Reaction Rates UNIT 3 Chapter 6: Rates of Reaction Section 6.1 Determining Reaction Rates The change in concentration of reactant or product over time is often graphed. For the reaction A → B, over time, the concentration of A decreases, and the concentration of B increases. Image source: MHR, Chemistry 12 © 2011. ISBN 07-106010-3; page 355 TO PREVIOUS SLIDE

Average and Instantaneous Reaction Rates UNIT 3 Chapter 6: Rates of Reaction Section 6.1 Average and Instantaneous Reaction Rates Average rate of reaction: change in [reactant] or [product] over a given time period (slope between two points) Instantaneous rate of reaction: the rate of a reaction at a particular point in time (slope of the tangent line) Image source: MHR, Chemistry 12 © 2011. ISBN 07-106010-3; page 356 Average rate of reaction and instantaneous rate of reaction can be determined from a graph of concentration vs. time. TO PREVIOUS SLIDE

Expressing Reaction Rates in Terms of Reactants or Products UNIT 3 Chapter 6: Rates of Reaction Section 6.1 Expressing Reaction Rates in Terms of Reactants or Products A known change in concentration of one reactant or product and coefficients of a chemical equation allows determination of changes in concentration of other reactants or products. TO PREVIOUS SLIDE

Answer on the next slide UNIT 3 Chapter 6: Rates of Reaction Section 6.1 Learning Check Express the rate of formation of ammonia relative to hydrazine, for the reaction on the previous slide. Answer on the next slide TO PREVIOUS SLIDE

Learning Check UNIT 3 The mole ratio of ammonia to hydrazine is 4:3 Chapter 6: Rates of Reaction Section 6.1 Learning Check The mole ratio of ammonia to hydrazine is 4:3 TO PREVIOUS SLIDE

Methods for Measuring Rates of Reaction UNIT 3 Chapter 6: Rates of Reaction Section 6.1 Methods for Measuring Rates of Reaction Image source: MHR, Chemistry 12 © 2011. ISBN 07-106010-3; page 362, Table 6.2 TO PREVIOUS SLIDE

Calculating Reaction Rates from Experimental Data UNIT 3 Chapter 6: Rates of Reaction Section 6.1 Calculating Reaction Rates from Experimental Data The following data were collected in order to calculate the rate of a reaction. Calculations on the next two slides show how to use volume data and mass data to determine the average rate of a reaction. TO PREVIOUS SLIDE

Calculating Reaction Rates from Experimental Data UNIT 3 Chapter 6: Rates of Reaction Section 6.1 Calculating Reaction Rates from Experimental Data TO PREVIOUS SLIDE

Calculating Reaction Rates from Experimental Data UNIT 3 Chapter 6: Rates of Reaction Section 6.1 Calculating Reaction Rates from Experimental Data TO PREVIOUS SLIDE

Section 6.1 Review UNIT 3 Chapter 6: Rates of Reaction Section 6.1 TO PREVIOUS SLIDE

6.2 Collision Theory and Factors Affecting Rates of Reaction UNIT 3 Chapter 6: Rates of Reaction Section 6.2 6.2 Collision Theory and Factors Affecting Rates of Reaction According to collision theory, a chemical reaction occurs when the reacting particles collide with one another. Only a fraction of collisions between particles result in a chemical reaction because certain criteria must be met. TO PREVIOUS SLIDE

Effective Collision Criteria 1: The Correct Orientation of Reactants UNIT 3 Chapter 6: Rates of Reaction Section 6.2 Effective Collision Criteria 1: The Correct Orientation of Reactants For a chemical reaction to occur, reactant molecules must collide with the correct orientation relative to each other (collision geometry). Image source: MHR, Chemistry 12 © 2011. ISBN 07-106010-3; page 365 Five of many possible ways that NO(g) can collide with NO3(g) are shown. Only one has the correct collision geometry for reaction to occur. TO PREVIOUS SLIDE

Effective Collision Criteria 2: Sufficient Activation Energy UNIT 3 Chapter 6: Rates of Reaction Section 6.2 Effective Collision Criteria 2: Sufficient Activation Energy For a chemical reaction, reactant molecules must also collide with sufficient energy. Activation energy, Ea, is the minimum amount of collision energy required to initiate a chemical reaction. Collision energy depends on the kinetic energy of the colliding particles. Image source: MHR, Chemistry 12 © 2011. ISBN 07-106010-3; page 366 The shaded part of the Maxwell-Boltzmann distribution curve represents the fraction of particles that have enough collision energy for a reaction (ie the energy is ≥ Ea). TO PREVIOUS SLIDE

Representing the Progress of a Chemical Reaction UNIT 3 Chapter 6: Rates of Reaction Section 6.2 Representing the Progress of a Chemical Reaction From left to right on a potential energy curve for a reaction: potential energy increases as reactants become closer when collision energy is ≥ maximum potential energy, reactants will transform to a transition state products then form (or reactants re-form if ineffective) Image source: MHR, Chemistry 12 © 2011. ISBN 07-106010-3; page 366 Exothermic Endothermic TO PREVIOUS SLIDE

Activation Energy and Enthalpy UNIT 3 Chapter 6: Rates of Reaction Section 6.2 Activation Energy and Enthalpy The Ea for a reaction cannot be predicted from ∆H. ∆H is determined only by the difference in potential energy between reactants and products. Ea is determined by analyzing rates of reaction at differing temperatures. Reactions with low Ea occur quickly. Reactions with high Ea occur slowly. Image source: MHR, Chemistry 12 © 2011. ISBN 07-106010-3; page 367 Potential energy diagram for the combustion of octane. TO PREVIOUS SLIDE

Activation Energy for Reversible Reactions UNIT 3 Chapter 6: Rates of Reaction Section 6.2 Activation Energy for Reversible Reactions Potential energy diagrams can represent both forward and reverse reactions. follow left to right for the forward reaction follow right to left for the reverse reaction Image source: MHR, Chemistry 12 © 2011. ISBN 07-106010-3; page 368 TO PREVIOUS SLIDE

Analyzing Reactions Using Potential Energy Diagrams UNIT 3 Chapter 6: Rates of Reaction Section 6.2 Analyzing Reactions Using Potential Energy Diagrams Image source: MHR, Chemistry 12 © 2011. ISBN 07-106010-3; page 369 The BrCH3 molecule and OH- collide with the correct orientation and sufficient energy and an activated complex forms. When chemical bonds reform, potential energy decreases and kinetic energy increases as the particles move apart. TO PREVIOUS SLIDE

Answer on the next slide UNIT 3 Chapter 6: Rates of Reaction Section 6.2 Learning Check Describe the relative values of Ea(fwd) and Ea(rev) for an exothermic reaction Answer on the next slide TO PREVIOUS SLIDE

Learning Check UNIT 3 Ea(rev) is greater than Ea(fwd) Chapter 6: Rates of Reaction Section 6.2 Learning Check Ea(rev) is greater than Ea(fwd) TO PREVIOUS SLIDE

Factors Affecting Reaction Rate UNIT 3 Chapter 6: Rates of Reaction Section 6.2 Factors Affecting Reaction Rate 1. Nature of reactants reactions of ions tend to be faster than those of molecules 2. Concentration a greater number of effective collisions are more likely with a higher concentration of reactant particles 3. Temperature with an increase in temperature, there are more particles with sufficient energy needed for a reaction (energy is ≥ Ea) TO PREVIOUS SLIDE

Factors Affecting Reaction Rate UNIT 3 Chapter 6: Rates of Reaction Section 6.2 Factors Affecting Reaction Rate 4. Pressure for gaseous reactants, the number of collisions in a certain time interval increases with increased pressure 5. Surface area a greater exposed surface area of solid reactant means a greater chance of effective collisions 6. Presence of a catalyst a catalyst is a substance that increases a reaction rate without being consumed by the reaction TO PREVIOUS SLIDE

A Catalyst Influences the Reaction Rate UNIT 3 Chapter 6: Rates of Reaction Section 6.2 A Catalyst Influences the Reaction Rate A catalyst lowers the Ea of a reaction. this increases the fraction of reactants that have enough kinetic energy to overcome the activation energy barrier a catalyzed reaction has the same reactants, products, and enthalpy change as the uncatalyzed reaction A catalyst decreases both Ea(fwd) and Ea(rev). Image source: MHR, Chemistry 12 © 2011. ISBN 07-106010-3; page 374 TO PREVIOUS SLIDE

Catalysts in Industry UNIT 3 Chapter 6: Rates of Reaction Section 6.2 Catalysts in Industry A metal catalyst is used for industrial-scale production of ammonia from nitrogen and hydrogen. Hydrogen and nitrogen molecules break apart when in contact with the catalyst. These highly reactive species then recombine to form ammonia. A catalyst (V2O5) is used for industrial-scale production of sulfuric acid from sulfur. Image source: MHR, Chemistry 12 © 2011. ISBN 07-106010-3; page 375 TO PREVIOUS SLIDE

Catalysts in Industry UNIT 3 Chapter 6: Rates of Reaction Section 6.2 Catalysts in Industry The Ostwald process uses a platinum-rhodium catalyst for the industrial production of nitric acid. Many industries use biological catalysts, called enzymes, which are most often proteins. For example: the use of enzymes decreases the amount of bleach (an environmental hazard) needed to whiten fibres used in paper production. TO PREVIOUS SLIDE

Section 6.2 Review UNIT 3 Chapter 6: Rates of Reaction Section 6.2 TO PREVIOUS SLIDE

6.3 Reaction Rates and Reaction Mechanisms UNIT 3 Chapter 6: Rates of Reaction Section 6.3 6.3 Reaction Rates and Reaction Mechanisms Initial rate is the rate of a chemical reaction at time zero. products of the reaction are not present, so the reverse reaction cannot occur it is a more accurate method for studying the relationship between concentration of reactant and reaction rate Reaction rates will decrease as time progresses. This is because of the presence of more and more product. Once product is present, the reverse reaction can occur. Therefore, the rate of a reaction at any point after time zero is going to be affected by the rate of the reverse reaction. Image source: MHR, Chemistry 12 © 2011. ISBN 07-106010-3; page 380 Initial rate is found by determining the slope of a line tangent to the curve at time zero. TO PREVIOUS SLIDE

Graphing Reaction Rate in Terms of Concentration UNIT 3 Chapter 6: Rates of Reaction Section 6.3 Graphing Reaction Rate in Terms of Concentration To study the effects of concentration on reaction rate: different starting concentrations of reactant are used initial rates are calculated using the slopes of the tangent lines from concentration vs time curves initial rates are plotted against starting concentration Image source: MHR, Chemistry 12 © 2011. ISBN 07-106010-3; page 381 Initial rates are determined (A) and these are plotted against concentration (B). TO PREVIOUS SLIDE

First-order Reactions UNIT 3 Chapter 6: Rates of Reaction Section 6.3 First-order Reactions The initial rate vs starting concentration graph on the previous slide is a straight line. the equation of the line can be expressed as: rate = k[A] This represents a first-order reaction For reactions with more than one reactant (e.g. A and B): if experiments for each reactant produce straight lines, the rate is “first order with respect to reactant A and first order with respect to reactant B.” TO PREVIOUS SLIDE

Second-order Reactions UNIT 3 Chapter 6: Rates of Reaction Section 6.3 Second-order Reactions For chlorine dioxide in this reaction: the initial rate vs concentration curve is parabolic the reaction is proportional to the square of [ClO2] it is a second order reaction with respect to this reactant Image source: MHR, Chemistry 12 © 2011. ISBN 07-106010-3; page 283 rate = k[A]2 TO PREVIOUS SLIDE

The Rate Law rate = k[A]m[B]n UNIT 3 Chapter 6: Rates of Reaction Section 6.3 The Rate Law The rate law shows the relationship between reaction rates and concentration of reactants for the overall reaction. rate = k[A]m[B]n m: order of the reaction for reactant A n: order of the reaction for reactant B k: rate constant m + n: order of the overall reaction TO PREVIOUS SLIDE

Reaction Mechanisms UNIT 3 Chapter 6: Rates of Reaction Section 6.3 Reaction Mechanisms A reaction mechanism is the series of elementary steps that occur as reactants are converted to products. For example, oxygen and nitrogen are not formed directly from the decomposition of nitrogen dioxide: It occurs in two elementary steps: The oxygen atom formed in the first elementary step is called an intermediate. An intermediate is a chemical species that appears in an elementary step, but not in the overall chemical equation. TO PREVIOUS SLIDE

The Rate-determining Step UNIT 3 Chapter 6: Rates of Reaction Section 6.3 The Rate-determining Step This reaction occurs in three elementary steps: Step 2 is the rate-determining step: it is the slowest elementary step the overall rate of the reaction is dependent on this step the Ea for this step is higher than Ea for each of the other steps TO PREVIOUS SLIDE

A Proposed Reaction Mechanism UNIT 3 Chapter 6: Rates of Reaction Section 6.3 A Proposed Reaction Mechanism Experiments show that this reaction is zero order with respect to OH– (i.e. its rate does not depend on [OH–]) This can be explained by a two-step mechanism Image source: MHR, Chemistry 12 © 2011. ISBN 07-106010-3; page 386 Step 2 is very fast and depends on completion of Step 1, not on the concentration of OH–. TO PREVIOUS SLIDE

Section 6.3 Review UNIT 3 Chapter 6: Rates of Reaction Section 6.3 TO PREVIOUS SLIDE