© Hitachi, Ltd All rights reserved. ICAO ACP WG-S Hitachi Ltd., 2014/3/28 SARPS Validation Discussion material on Web-EX 1 IP01 ACP WG S_28 Mar Web meeting

© Hitachi, Ltd All rights reserved. Validation items and major Conditions 1.Validation items for Hitachi’s BS  3.5 SPECTRAL MASK AND EMISSION  Maximum BER  4.6 SECURITY SERVICE 2. Conditions of testing  Frequency band : 5091MHｚ～5150MHz (SARPS:5030MHｚ～5150MHｚ）  Measure PER not BER Radio system with FEC system, measurement by PER is now commonly used, and the method is published by WiMAX Forum testing documents. Refer to the IP.  CTC, convolution turbo coding, is used as the coding scheme for measuring receiver sensitivity.  Uplink 64QAM is option (not validated) (3.5.4/ 3.5.6/ 4.4.4)  Prototype BS is prepared by Hitachi.  Measured system for 3.5 and are wire-connected in indoor LAB.  The tested center frequencies are following three points. Low Ch;5095MHz, Mid Ch:5120MHz, High Ch:5145MHz  Testing items for Security services function need to be discussed. 2

© Hitachi, Ltd All rights reserved. Appendix 3

© Hitachi, Ltd All rights reserved. 1. Emission Test MHｚ Table 1 Spectral Mask Parameter Frequency Band(MHz) ABCC´D 5MHz ５7.5 A B C C´ D dB Tx Spectral Mask -40 Spectrum MASK is as following condition. Emission power would be measured if it is less than these spectrum masks. BS transmission waves are captured by Spectrum Analyzer. 4

© Hitachi, Ltd All rights reserved. 2.1 Power Control SARPS description is as follows The AeroMACS radios shall implement power control Power control would be confirmed by observing the power control function of BS to MS, changing the path-loss value between BS and MS by Attenuator. The confirmed criteria is that transmission power would be changed by BS. 5

© Hitachi, Ltd All rights reserved. 2.2 Receiver Rejection ItemModulationSignal levelInterference level Adjacent channel (+/-5MHz) QAM-3/4Smin + 3dBSmin + 10dB QAM-3/4Smin + 3dBSmin + 4dB Second adjacent channel(+/-10MHz) QAM-3/4Smin + 3dBSmin + 29dB QAM-3/4Smin + 3dBSmin + 23dB Table 2 Minimum Rejection for adjacent or second adjacent Channel is confirmed by measuring the error rate, which is less than PER, which is equivalent to BER of less than 10e-6. PER is calculated to BER by following equation. PER = 1 – ( 1 – BER) n n : bits unit size of FEC block The signal level is +3dB with correspondent level of adjacent channel interference and second adjacent channel as following table are added. Since the Uplink 64QAM is optional, BS is not applicable for Receiving 64QAM. 6

© Hitachi, Ltd All rights reserved. 2.3 Maximum BER(1/2) SARPS :4.4.4 The maximum bit error rate shall not exceed BER 10e-6 after FEC assuming a minimum received signal equal to the corresponding sensitivity level. PER is calculated to BER by following equation. PER = 1 – ( 1 – BER) n n : one unit size of FEC block Measure the maximum error rate with a minimum received signal equal to the corresponding sensitivity level. 7

© Hitachi, Ltd All rights reserved. This Signal sensitivity level data as following table is used by coding scheme CTC. Data is derived from MOPS; Appendix C （AeroMACS minimum receiver sensitivity would be 2dB lower than indicated, if CTC is used) Modulation and Coding Scheme Rep. Factor DLSensitivity UL (dBm) CTC-64QAM-3/ CTC-64QAM-2/ CTC-16QAM-3/ CTC-16QAM-1/ CTC-QPSK-3/ CTC-QPSK-1/ CTC-QPSK-1/ UL 64QAM is option for BS reception Table3 Receiver Sensitivity Maximum BER(2/2)

© Hitachi, Ltd All rights reserved. 2.5 Security Service(1/2) Regarding SECURITY SERVICE functions, we think testing methods are as follows. SARPSTesting itemTesting contents Refer standardTesting Method 4.6.1integrity of messages confirmed by CRC field MOPS : Cyclic Redundancy Check(CRC) Try 1 call between MS and BS while measuring by monitor function. Confirm the sequence on AeroMACS radio path（R1）, and item field, which should be confirmed in message. are memorized by monitor ensure the authenticity of messages confirmed by CMAC field MOPS : Cipher-based message authentication code (CMAC) 4.6.4confidentiality of messages confirmed by TEK function. MOPS : Traffic Encryption Key (TEK) 4.6.5authenticate users of the system confirmed by EAP function MOPS : EAP Authentication 9

© Hitachi, Ltd All rights reserved. 2.6 Security Service(2/2) SARPSTesting itemTesting Contents status Testing Items to be confirmed 4.6.3availability of the system Should be confirmed The function which guarantee the transferred data integrity would be confirmed by EAP function. The definition of availability should be confirmed authorize the permitted actions of users (authorized uses during unauthorized events) Should be confirmed This is not confirmed by equipment level, but should be confirmed by system level. The definition of permitted action should be cleared. Confirm authorized uses during unauthorized events prevent intrusion from lower integrity information domain to higher integrity information domain Should be confirmed This is not confirmed by equipment level, but should be confirmed by system level. How to prevent intrusion method should be defined. 10 Following items need to be discussed.

11