Tony Bougebrayel Paper Engineer Analyst

Slides:

Advertisements

Similar presentations

WATERLOO ELECTRICAL AND COMPUTER ENGINEERING 60s: Power Engineering 1 WATERLOO ELECTRICAL AND COMPUTER ENGINEERING 60s Power Engineering Department of.

Advertisements

Department of Mechanical Engineering University of Delaware Michael H Santare, PhD Mechanical Engineering.

AE/ME 339 Computational Fluid Dynamics (CFD) K. M. Isaac Professor of Aerospace Engineering.

Tony Y. Bougebrayel, PE, PhD

Engineering Mechanics Group Faculty of Aerospace Engineering Minor Programme 2 Aerospace Analysis and Development.

MECH300H Introduction to Finite Element Methods

Airflows and the spread of airborne pathogens in the ICU Dr Collette W

© 2000 Swagelok Company DP Series Springless Diaphragm Valves.

University of Cincinnati Mechanical Engineering Program School of Dynamic Systems GE-ACE Program Feb. 1, 2012.

Biofluid Mechanics and Bioheat Transfer

NATIONAL RESEARCH AND DEVELOPMENT INSTITUTE FOR GAS TURBINES COMOTI ROMANIA

Tony Bougebrayel, PE, PhD Engineering Analyst Swagelok Co.

Computer Aided Mechanical Design

Nilufa Rahim C2PRISM Fellow Sept. 12, What is Engineering? Engineering is the field of applying Science and Mathematics to develop solutions that.

Department Overview Alejandro Diaz Chair, Mechanical Engineering.

Fluid Mechanics –I Surveying –I Mechanics of Solids Building Materials

A tour of course. Physics Course Objectives: At the end of this course the students will be able to: - Discuss science as a body of knowledge.

ROWAN UNIVERSITY COLLEGE OF ENGINEERING Eric Constans Chair Mechanical Engineering.

MECHANICAL TECHNOLOGY. What is Mechanical Technology? It is the application of physical principles and current technological developments to the creation.

MECH345 Introduction to Finite Element Methods Chapter 1 Numerical Methods - Introduction.

Computational Fluid Dynamics in OpenFOAM Henrik Kaald Melbø Supervisor: Heinz Preisig Department of Chemical Engineering.

Unit: Science of Technology Lesson 1: Applied Chemistry.

AE/ME 339 Computational Fluid Dynamics (CFD) K. M. Isaac Professor of Aerospace Engineering Introduction and Scope.

ME Curriculum. Thermal Systems  Thermodynamics  Thermo (heat) & dynamics (force and motions  work): the science that deals with heat, work, and conversion.

School of Mechanical Engineering FACULTY OF ENGINEERING School of Mechanical Engineering FACULTY OF ENGINEERING Aerodynamic Design Optimization Harvey.

PRESENTATION OF CFD ACTIVITIES IN CV GROUP Daniel Gasser.

Mechanical Engineer Mechanical engineering is the study of motion, energy and force. The mechanical engineer seeks to control these elements by using.

2 First academic year students 600 first-year students in the last academic year 200 graduated in the last year 1600 graduated since 1996.

Euler equations of Gas Dynamics Hailiang Liu October 15, 2004.

Trojan UV Swift SC. Introduction Designed to meet the needs of the small community, the TrojanUVSwift™SC is ideally suited for smaller flow applications.

DEVELOPMENT OF GAS-FOIL BEARINGS FOR MINIATURIZED RTB CRYOCOOLERS – PHASE III MATHEMATICAL MODELING AND ANALYSIS – I Presented by  K.V.Krishna Murty MMAE.

CFD Role in Thailand’s Electronics Manufacturing Ekachai Juntasaro CFD Lab School of Mechanical Engineering Institute of Engineering Suranaree University.

GWU BME Fellowship Flow Over the Human Hand Mentor: Dr. Rajat Mittal Presenter: Ryan Kelly.

Johnathan Bolton, Anpeng He, Ning Zhang (Ph.D.) Department of Engineering McNeese State University ULS Academic Summit April 12-13, 2013 DISCHARGE SOURCE.

ANSYS. Overview of ANSYS It is an engineering simulation software developed in 1970 by Dr. John A. Swanson It was developed to use finite element analysis.

Computational Fluid Dynamics (CFD) Simulations for Industry G. R. Shevare Department of Aerospace.

Advanced Numerical Techniques Mccormack Technique CFD Dr. Ugur GUVEN.

Manufacturing Process Modeling engineer(m/f)

Mechanical & Manufacturing Engineering Program

Finite Difference Methods

Connector Event Presentation Wind Energy Technologies Technologies for efficient and low-noise wind turbine in the making Riadh Habash, PhD, P.Eng.

Heat Transfer Lab Equipment

Manufacturing Process Modeling engineer(m/f)

Accepted Students Program

MEP & Stress Analysis Services in India

Reasons to Study Mechanical Engineering

Nature of Technology.

Design Tools and Resources

Basics Semiconductors

上海理工大学 University Of Shanghai For Science And Technology

CFD – Fluid Dynamics Equations

Numerical Study of the Wall Slip Reduction Effects for a Double Concentric Cylinder Rheometer with Slotted Rotor D. De Kee, Department of Chemical and.

Class # 27 ME363 Spring /23/2018.

ME/AE 339 Computational Fluid Dynamics K. M. Isaac Topic2_PDE

أنماط الإدارة المدرسية وتفويض السلطة الدكتور أشرف الصايغ

Numerical Modeling of Fluid Droplet Spreading and Contact Angle Hysteresis Nikolai V. Priezjev, Mechanical Engineering, Michigan State University, MI

Manager, Marketing Resources

Суури мэдлэг Basic Knowledge

The Society for Experimental Mechanics (SEM) Overview

Interdisciplinary Research using 3D graphics

Use your Journal to Name the Transformations

1.03 Career Options.

Connecting Catalytic Chemistry to External Particle Conditions via CFD Anthony G. Dixon, Department of Chemical Engineering, Worcester Polytechnic Institute.

Mechanical engineering technician

AE/ME 339 Computational Fluid Dynamics (CFD) K. M. Isaac 7/24/2019

Simulation Based Study of Effects of Water Waves on Turbulence

AE/ME 339 Computational Fluid Dynamics (CFD) K. M. Isaac

Compact Heat Exchanger

Presentation transcript:

Tony Bougebrayel Paper Engineer Analyst Tony Bougebrayel has worked at Swagelok since 1987. He started out in the manufacturing area and eventually moved on to product design area. He has broad knowledge of Swagelok’s products – especially in the areas of Semiconductor and Instrumentation. In 1997 Tony took the lead in building Swagelok’s in-house Computational Fluid Dynamics (CFD) capabilities. Currently, he holds the position of Engineer Analyst providing CFD and technical flow energy support to the Swagelok organization. Tony received a PhD in Mechanical Engineering in May 2002 from Cleveland State University. His main area of study was fluid and thermal energy with emphasis on numerical solutions. Paper