CHAPTER 8 Friction To introduce the concept of dry friction and show how to analyze the equilibrium of rigid bodies subjected to this force.

Slides:



Advertisements
Similar presentations
8.6 Frictional Forces on Collar Bearings, Pivot Bearings and Disks
Advertisements

CHARACTERISTICS OF DRY FRICTION & PROBLEMS INVOLVING DRY FRICTION
FRICTION (Sections ) Today’s Objective:
Friction MET 2214 Part 1.
Lecture 24 ENGR-1100 Introduction to Engineering Analysis.
FRICTION (Sections ) Today’s Objective: Students will be able to: a) Understand the characteristics of dry friction. b) Draw a FBD including friction.
READING QUIZ The friction that exist between two contacting surfaces in the absence of lubrication is called _________. A) fluid friction B) normal friction.
CHAPTER 8 FRICTION.
8.2 Problems Involving Dry Friction
CHARACTERISTICS OF DRY FRICTION & PROBLEMS INVOLVING DRY FRICTION
Example 8.1 The uniform crate has a mass of 20kg. If a force
Engineering Mechanics: Statics Chapter 8: Friction Chapter 8: Friction.
เป็นเครื่องกลอย่างง่ายที่แปลงแรงให้เป็นแรงขนาดใหญ่ขึ้นในแนวตั้งฉาก
8.2 Problems Involving Dry Friction
Chapter 8 - Friction Sections Friction w Frictional forces resist movement of a rigid body over a rough surface. w It is assumed that the.
CHARACTERISTICS OF DRY FRICTION & PROBLEMS INVOLVING DRY FRICTION
Apply the three equations of motion for a rigid body in planar motion. Analyze problems involving translational motion. PLANAR KINETIC EQUATIONS OF MOTION:
Mechanics 1 Friction.
Quiz #5 Determine the internal normal force, shear force and moment at points D and E of the frame.
CP Physic Chapter 5 Review 1. The coefficient of kinetic friction is ______ the coefficient of static friction? ans: less than 2. Which of the following.
Frictional Force A force that opposes motion Acts parallel to the
Friction Lecture 8 Friction: is defined as a force of resistance acting on a body which prevents or retards slipping of the body relative to a second.
Newton’s Laws of Motion
UNIT - V FRICTION.
FRICTION Friction 1 Friction is defined as the contact resistance exerted by one body upon another body when one body moves or tends to move past another.
Chapter 4B. Friction and Equilibrium
Chapter six: Friction Section A Frictional Phenomena 1.
CHARACTERISTICS OF DRY FRICTION & PROBLEMS INVOLVING DRY FRICTION
Physics 111: Mechanics Lecture 5
Friction The force which opposes the movement or the tendency of movement is called Frictional force or simply friction. It is due to the resistance to.
CHARACTERISTICS OF DRY FRICTION & PROBLEMS INVOLVING DRY FRICTION
FRICTION Friction 1 Friction is defined as the contact resistance exerted by one body upon another body when one body moves or tends to move past another.
Chapter 4B. Friction and Equilibrium
Normal Force and Friction Force
CHARACTERISTICS OF DRY FRICTION & PROBLEMS INVOLVING DRY FRICTION
Section 5.8: Friction.
Chapter 4B. Friction and Equilibrium
Everyday Forces Friction Force. Types of Friction forces
SPH4U: Friction What is it? Systematic catagories of forces
CHARACTERISTICS OF DRY FRICTION & PROBLEMS INVOLVING DRY FRICTION
CHARACTERISTICS OF DRY FRICTION & PROBLEMS INVOLVING DRY FRICTION
Friction is one of the most important opposing forces.
University Tun Hussein Onn Malaysia (UTHM),
Objectives Chapter 4 Section 4 Everyday Forces
Two Dimensional Forces
Friction.
PLANAR KINETIC EQUATIONS OF MOTION:
Chapter Objectives Chapter Outline
Examples.
FRICTION.
STATICS (ENGINEERING MECHANICS-I)
FRICTION.
FRICTION.
FRICTION.
FRICTION.
Friction.
Friction.
Engineering Mechanics: Statics
FRICTION.
FRICTION.
Section 5.8: Friction.
FRICTION.
FRICTION (Sections ) Today’s Objective:
FRICTION (Sections ) Today’s Objective:
FRICTION.
Some Particular Forces
Bölüm 8 Sürtünme W A horizontal force P applied to a block will not at first cause it to move. This is because the friction force F balances P. P F As.
ENGINEERING MECHANICS
Engineering Mechanics: Statics
CE Statics Chapter 8 – Lecture 1.
Presentation transcript:

CHAPTER 8 Friction To introduce the concept of dry friction and show how to analyze the equilibrium of rigid bodies subjected to this force

Dry Friction Friction is defined as a force of resistance acting on a body which prevents or retards slipping of the body relative to a second body. Experiments show that frictional forces act tangent (parallel) to the contacting surface in a direction opposing the relative motion or tendency for motion.

For the body shown in the figure to be in equilibrium, the following must be true: F = P, N = W, and Wx = Ph.

FS = msN Fk = mkN Impending motion Motion coefficient of kinetic friction coefficient of static friction

The maximum friction force is attained just before the block begins to move (a situation that is called “impending motion”). The value of the force is found using Fs = s N, where s is called the coefficient of static friction. The value of s depends on the materials in contact.

PROBLEMS INVOLVING DRY FRICTION Steps for solving equilibrium problems involving dry friction: 1. Draw the necessary free body diagrams. Make sure that you show the friction force in the correct direction (it always opposes the motion or impending motion). 2. Determine the number of unknowns. Do not assume F = S N unless the impending motion condition is given. 3. Apply the equations of equilibrium and appropriate frictional equations to solve for the unknowns.

A block with weight W The inclination, s, is noted. Analysis of the block just before it begins to move gives (using Fs = s N): + Fy = N – W coss = 0 + FX = S N – W sins = 0 s = (W sin s ) / (W cos s ) = tan s

Pushing the uniform crate that has a weight W and sits on the rough surface. Static, Slip or tip over?

Verge of slipping Tip over

3 Number of unknowns? Number of E-of-E ∑Fx = 0 ∑Fy = 0 ∑M = 0 3

Example 8.1 The uniform crate has a mass of 20kg. If a force P = 80N is applied on to the crate, determine if it remains in equilibrium. The coefficient of static friction is μ = 0.3.

Solution Resultant normal force NC act a distance x from the crate’s center line in order to counteract the tipping effect caused by P 3 unknowns to be determined by 3 equations of equilibrium

SOLUTION SOLVING

Solution Since x is negative, the resultant force acts (slightly) to the left of the crate’s center line No tipping will occur since x ≤ 0.4m Maximum frictional force which can be developed at the surface of contact Fmax = μsNC = 0.3(236N) = 70.8N Since F = 69.3N < 70.8N, the crate will not slip.

Example 8.2 It is observed that when the bed of the dump truck is raised to an angle of θ = 25° the vending machines begin to slide off the bed. Determine the static of coefficient of friction between them and the surface of the truck

Solution Idealized model of a vending machine lying on the bed of the truck Dimensions measured and center of gravity located Assume machine weighs W

Dimension x used to locate position of the resultant normal force N FBD Solution Dimension x used to locate position of the resultant normal force N 4 unknowns N, F, µs, x

Equations Of Equilibrium, 4 unknowns N, F, µs, x Equations Of Equilibrium, Since slipping impends at θ=25°, Using the first two equations, we have

Solution Angle θ = 25°is referred as the angle of repose By comparison, θ = Φs θ is independent of the weight of the vending machine so knowing θ provides a method for finding coefficient of static friction θ = 25°, x = 0.233m (moment equation) Since 0.233m < 0.3m the vending machine will slip before it can tip.

Quiz 1 The horizontal force is P=80N, Determine the normal and frictional forces acting on the crate of weight 300N. The friction coefficients are μs= 0.3 and μk=0.2

Quiz 2 Determine the magnitude of force P needed to start towing the crate of mass M=40kg. Also determine the location of the resultant normal force acting on the crate, measured from point A. μs= 0.3

Quiz 3 Determine the friction force on the crate of mass M=40Kg, and the resultant normal force and its position x, measured from point A, if the force is P=300N. μs= 0.3 and μk=0.2

The uniform dresser has a weight of 360 N and rest on a tile floor Quiz 4 30o The uniform dresser has a weight of 360 N and rest on a tile floor which ms = 0.25 Determine the smallest magnitude of force F needed to move the dresser. [ F = 121.45 N] If the man has a weight of 600 N, determine the smallest coefficient of static friction between his shoes and the floor so that he does not slip. [ms = 0.195]

FBD 1 FBD 2

Determine the smallest magnitude of force F needed to move the dresser.

If the man has a weight of 600 N, determine the smallest coefficient of static friction between his shoes and the floor so that he does not slip. Fm

Tutorial 2 Q1 The crate has a mass M=350N and is subjected to a towing force P acting at an angle 20° with the horizontal. If the coefficient of static friction is μ=0.5, determine the magnitude of P to just start the crate moving down the plane.

Tutorial 2 Q2 A packing crate of mass 40 kg is pulled by a rope as shown. The coefficient of static friction between the crate and the floor is 0.35. If α =40°, determine the magnitude of the force P required for impending motion of the crate (b) whether sliding or tipping is impending.