Analog and Baseband Beam Tracking in ay

Slides:



Advertisements
Similar presentations
Doc.: IEEE /0883r1 Submission July 2010 Slide 1 Comment Resolution for “Spatial Reuse” Subgroup Date: Authors: Thomas Derham, Orange.
Advertisements

Month Year doc.: IEEE yy/xxxxr0 July 2015
Doc.: IEEE /1321r0 Submission Reducing Explicit MIMO Compressed Beamforming Feedback Overhead for ax November 2015 Slide 1 Date:
Submission doc.: IEEE /0103r0 January 2016 Assaf KasherSlide 1 Beamforming Training proposals Date: Authors:
Doc.: IEEE /0626r1 Submission Feedback Element Compression for ax May 2016 Slide 1 Date: Authors: Kome Oteri (InterDigital)
InterDigital, Inc. Submission doc.: IEEE /0911r1 July 2016 Link Level Performance Comparisons of Open Loop, Closed Loop and Antenna Selection.
Beam Tracking for ay Date: Authors: January 2017
MU MIMO beamforming protocol proposal
Bandwidth signaling for EDMG
Multi-Stage, Multi-Resolution Beamforming Training for ay
Closed Loop SU-MIMO Performance with Quantized Feedback
Open Loop vs Closed Loop SU-MIMO for 11ay
Month Year doc.: IEEE yy/xxxxr0 November 2016
Improvements to enhanced SLS beamforming
GI Overhead/Performance Impact on Open-Loop SU-MIMO
Locationing Protocol for 11az
EDMG capabilities for Open Loop Spatial Multiplexing in SU-MIMO
Clarification on TRN Subfield Definition for MIMO
Beamforming for mmWave Distribution Networks
TRN Subfield for Channel Aggregation
BRP Transmit Sector Sweep
Channel Estimation Field for EDMG OFDM PHY in 11ay
Header Compression Date: Authors: May 2012 Month Year
Maximum Tone Grouping Size for ax Feedback
Feedback Element Compression for ax
Further Discussion on Beam Tracking for ay
Hybrid Beamforming Protocol Design Details
Protocols for Hybrid Beamforming in ay
Analog and Baseband Beam Tracking in ay
Maximum Tone Grouping Size for ax Feedback
Asymmetric beamforming training procedure enhancements
MU Beamforming for mmWave Distributed Network
Clarification on TXSS Sector List Feedback
Resource Allocation for Unassociated STAs – Follow Up
MU-MIMO channel access flow for 11ay
Feedback Element Compression for ax
Maximum Tone Grouping Size for ax Feedback
Improvement to TWT Parameter set selection
Multi-BF Procedure for 11ay
Further Discussion on Beam Tracking for ay
First Path FTM SFD Text Date: Authors: December 2017
Enhanced Beam Tracking Against Blockage: Resolution to CID 145
Hybrid Beamforming Protocol Design Details
Consideration on multi-AP coordination for EHT
Adding control trailer to control mode PPDUs
Further discussion for WLAN Radar
Protocols for Hybrid Beamforming in ay
Discussion on SLS with different Tx and Rx antennas
Explicit Block Ack Request in DL MU PPDU
Multi-BF Procedure for 11ay
Unsolicited RSS for SLS in DTI
Preliminary design of EDMG PHY headers
Selective Segment Retransmission of VHT Compressed Beamforming
Generalized Multi-Beamforming for 11ay
Clarification on TXSS Sector List Feedback
Header-A Definition for EDMG Control Mode
BTI and A-BFT for EDMG AP with Multiple Antennas
EDMG capabilities for Open Loop Spatial Multiplexing in SU-MIMO
Header-A Definition for EDMG Control Mode
SU-MIMO and MU-MIMO link access
MIMO phase in MU-MIMO Beamforming
Discussion on Rank Adaptation
Fixed Inter Frame Spacing for BRP in ay
Clarification on TRN Subfield Definition for MIMO
NAV Update Rule Considering UL MU Operation
Feedback of Short SSW Packet Based Sector Sweep in DTI
Control Trailer Clarifications
First Path FTM SFD Text Date: Authors: December 2017
SM Power Save for 11ay Date: Authors: August 2017
Enhanced Beam Tracking Against Blockage: Resolution to CID 145
Presentation transcript:

Analog and Baseband Beam Tracking in 802.11ay Month Year doc.: IEEE 802.11-yy/xxxxr0 July 2017 Analog and Baseband Beam Tracking in 802.11ay Date: 2017-07-10 Authors: Kome Oteri (InterDigital) Kome Oteri(InterDigital)

July 2017 doc.: IEEE 802.11-15/xxxxr0 July 2017 Introduction In [1], an agreement was made to enable mechanisms that support tracking of the baseband channel for SU-MIMO and MU-MIMO hybrid beamforming in 802.11ay Motion #195: Do you agree to include mechanisms that support tracking of the baseband channel for SU-MIMO and MU-MIMO hybrid beamforming in 802.11ay ? Yes/No/Abstain: 9/3/11 In this contribution, we define the protocol and signaling needed to enable both analog and baseband beam tracking for 802.11ay. This includes: The different types of beam tracking: DMG, EDMG: Analog (EDMG:A), EDMG: baseband (EDMG:B) The training signals The feedback The use cases We also show associated spec text to enable the elements mentioned above Kome Oteri (InterDigital) Kome Oteri(InterDigital)

July 2017 doc.: IEEE 802.11-15/xxxxr0 July 2017 Beam Tracking Beam tracking enables an initiator or responder track the change in its beams without the need for the signaling and overhead of a BRP procedure. The signaling for beam tracking is sent in the DMG BRP packet header fields or EDMG header-A fields either in a standalone frame or piggy-backed on other transmitted frames. In 802.11ad, three beam tracking schemes are defined [3]: Initiator Receive Beam Tracking Initiator Transmit Beam Tracking Responder Receive Beam Tracking Kome Oteri (InterDigital) Kome Oteri(InterDigital)

Beam Tracking Types in 802.11ad July 2017 Beam Tracking Types in 802.11ad In 802.11ad beam tracking may be one of three types: Initiator Receive Beam Tracking: The initiator sends a request to the responder and the responder sends a tracking packet to enable the initiator estimate its receive beams Initiator Transmit Beam Tracking: The initiator sends a training packet to the receiver and the receiver feeds back the desired feedback Responder Receive Beam Tracking: The initiator sends a training sequence to the responder and requests that it track its receive beams. Kome Oteri (InterDigital)

July 2017 doc.: IEEE 802.11-15/xxxxr0 July 2017 Beam Tracking for 802.11ay For 802.11ay, two types of beam tracking can be defined: Analog Beam Tracking (AB): used to track the change in analog beams e.g. due to STA rotation, movement or blockage. Similar to 802.11ad tracking but updated for SU/MU-MIMO Baseband Beam Tracking (BB): used to track the change in the “effective baseband channel” ( 𝐻 𝐵𝐵 ) for a fixed set of analog beams in SU/MU MIMO scenarios Requires feedback of information for new baseband beams based on original analog beams (skips the analog procedure). 𝑌= 𝐹 𝐵𝑟 𝐹 𝐴𝑟 𝐻 𝐹 𝐴𝑡 𝐹 𝐵𝑡 𝑥+𝑛 ; 𝐻 𝐵𝐵 = 𝐹 𝐴𝑟 𝐻 𝐹 𝐴𝑡 H = MIMO channel; HBB = effective baseband MIMO channel FAr , FAt = Analog beamformer; FBt ,FBr = Baseband beamformer Kome Oteri (InterDigital) Kome Oteri(InterDigital)

July 2017 Baseband Tracking Can estimate baseband channel efficiently by eliminating additional TRN fields in TRN packet for Initiator Transmit Beam Tracking (defined with EDMG_TRN_M). EDMG_TRN_M and EDMG_TRN_N fields are reserved while only EDMG_TRN_P field and EDMG_TRN_LEN fields are defined Kome Oteri (InterDigital)

Steps for Beam Tracking in 802.11ay July 2017 Steps for Beam Tracking in 802.11ay Setup Indicate if analog beam (AB) or baseband beam (BB) tracking request : (AB or BB) Indicate type of TRN packet and EDMG_TRN_length Define EDMG_P, EDMG_M and EDMG_N if applicable Training (for BB) Set baseband precoder to a fixed orthogonal matrix e.g. Identity matrix Transmit TRN units (T and P sub-units only) Indicate Feedback type required (default or explicitly signaled) Best Beam(s), SNR(s): (AB only) Channel Feedback or hybrid beamforming feedback (TBD): (AB or BB) Kome Oteri (InterDigital)

Beam Tracking Specification July 2017 Beam Tracking Specification Kome Oteri (InterDigital)

Beam Tracking Specification July 2017 doc.: IEEE 802.11-15/xxxxr0 July 2017 Beam Tracking Specification The beam tracking specification needs to define the following: TXVECTOR/RXVECTOR settings: Defines a parameter used for the specific beam tracking type Packet Signaling between STAs: Communicates the beam tracking parameters set in TXVECTOR/RXVECTOR between STAs DMG: BRP packet header EDMG / EDMG (B) : BRP packet header + EDMG Header-A Training : Enables the measurement DMG: AGC + TRN Units EDMG:A / EDMG:B : TRN Units (EDMG_TRN_length, T, P, M and N) Feedback (case dependent): Enables feedback of the beam tracking measurements if required The feedback type is the same as last feedback type if previously requested. If the feedback type has never been requested, explicitly request for feedback. Kome Oteri (InterDigital) Kome Oteri(InterDigital)

Current Beam Tracking Specification July 2017 doc.: IEEE 802.11-15/xxxxr0 July 2017 Current Beam Tracking Specification DMG [3] EDMG [2] Kome Oteri (InterDigital) Kome Oteri(InterDigital)

Updated Beam Tracking Specification July 2017 Updated Beam Tracking Specification EDMG with Analog/Baseband Tracking Kome Oteri (InterDigital)

Updated TRN-Packet Definition July 2017 Updated TRN-Packet Definition Initiator Receive Beam Tracking : TRN-R packet If EDMG_BEAM_TRACKING_TYPE parameter in the RXVECTOR is Baseband Beam Tracking, the baseband beamformers at the initiator and responder should be set to a predetermined orthogonal matrix, e.g., the identity matrix, during the transmission of the appended TRN-R subfields only and the measurement at the initiator is based on the appended TRN-R packets. Initiator Transmit Beam Tracking : TRN-T packet If the EDMG_BEAM_TRACKING_TYPE parameter in the TXVECTOR is Baseband Beam Tracking, then EDMG_TRN_LEN TRN units are appended to the data packet (each with EDMG_TRN_P TRN subfields) and are transmitted using the same AWV as the preamble and data field of the packet. The baseband beamformer for the initiator and responder should be set to a predetermined orthogonal matrix, e.g., the identity matrix, during the transmission of the appended TRN-T subfields only and the measurement is based on the appended TRN-T subfields. Kome Oteri (InterDigital)

July 2017 Updated Feedback The feedback type shall be the same as the feedback type in the last BRP frame that was transmitted from the initiator to the responder with TX-TRN-REQ equal to 1. If the responder has never received a BRP frame from the initiator with TX-TRN-REQ equal to 1, and - If BEAM_TRACKING_REQUEST parameter in the RXVECTOR is Beam Tracking Requested, or if EDMG_BEAM_TRACKING_REQUEST parameter in the RXVECTOR is Beam Tracking Requested and EDMG_BEAM_TRACKING_TYPE is Analog Beam Tracking, the responder shall respond with all subfields of the FBCK-TYPE field equal to 0 and set the BS-FBCK field to the index of the TRN-T subfield that was received with the best quality. - If EDMG_BEAM_TRACKING_REQUEST parameter in the RXVECTOR is Beam Tracking Requested and EDMG_BEAM_TRACKING_TYPE is Baseband Beam Tracking, the initiator shall include a FBCK-REQ in a DMG Beam Refinement element as in 9.4.2.130 and request for the feedback needed. The responder shall respond with the requested feedback. Kome Oteri (InterDigital)

July 2017 Updated Use Cases A beam tracking initiator may transmit to the beam tracking responder a PPDU requesting transmit beam tracking if at least one of the following conditions is met: — The time duration since the last PPDU it transmitted to the beam tracking responder that requested transmit beam tracking is greater than dot11BeamTrackingTimeLimit plus BRPIFS. — A BRP frame with the channel measurement feedback from the beam tracking responder has been received. In addition, a beam tracking initiator or beam tracking responder may request baseband beam tracking if at least one of the following conditions is met: The performance of the system is degraded in a hybrid beamforming transmission and the requestor would like to re-estimate the baseband beams as part of the link adaptation procedure The requestor did not request for detailed baseband beam information as part of the MIMO setup procedure. In this case, the analog beams have been identified but the information to design the baseband beams is still needed. Kome Oteri (InterDigital)

Conclusion Beam Tracking in 802.11ay has been discussed. July 2017 Conclusion Beam Tracking in 802.11ay has been discussed. The beam tracking for hybrid beamforming in 802.11ay may be : Analog Beam tracking Baseband Beam tracking Signaling and Procedures for both Analog and Baseband Beam tracking in 802.11ay are proposed. Kome Oteri (InterDigital)

July 2017 References [1] K. Oteri et. al., “Further Discussion on Beam Tracking for 802.11ay” IEEE doc. 11-17/0426r2, March 2017 [2] IEEE P802.11ay™/D0.3, January 2017 [3] IEEE Std 802.11-2016, December 2016 [4] K. Oteri et. al., “Protocols for Hybrid Beamforming in 802.11ay”, IEEE doc. 11-17/0429r3, January 2017 [5] A. Maltsev, et al, “Channel models for IEEE 802 11ay”, IEEE doc. 11- 15/1150r8 [6] K. Oteri et. al., “Draft Text for Analog and baseband Beam Tracking in 802.11ay” IEEE doc. 11-17/1097r0, July 2017 Kome Oteri (InterDigital)

Straw Poll Do you agree: July 2017 Straw Poll Do you agree: to the changes in the specification draft as described in IEEE 802.11-17/1097r0 to define Beam Tracking and its associated signaling and procedures? Kome Oteri (InterDigital)

July 2017 Appendix Signaling and Packet Exchange for Beam Tracking in 802.11ad and 802.11ay Kome Oteri (InterDigital)

Initiator Receive Beam Tracking (DMG) July 2017 Initiator Receive Beam Tracking (DMG) Kome Oteri (InterDigital)

Initiator Receive Beam Tracking (EDMG:A) July 2017 Initiator Receive Beam Tracking (EDMG:A) Kome Oteri (InterDigital)

Initiator Receive Beam Tracking (EDMG:B) July 2017 Initiator Receive Beam Tracking (EDMG:B) Kome Oteri (InterDigital)

Initiator Transmit Beam Tracking (DMG) July 2017 Initiator Transmit Beam Tracking (DMG) Kome Oteri (InterDigital)

Initiator Transmit Beam Tracking (EDMG:A) July 2017 Kome Oteri (InterDigital)

Initiator Transmit Beam Tracking (EDMG:B) July 2017 Initiator Transmit Beam Tracking (EDMG:B) Kome Oteri (InterDigital)