4 channels, each as input or output

Slides:

Advertisements

Similar presentations

Welcome Herzlich Willkommen Bienvenue JUMO eTRON T data sheet

Advertisements

SIRIUS Motor Management

5.5 The potential divider. 6V 3V 5.5 The potential divider.

EML 2023 – Motor Control Lecture 4 – DAQ and Motor Controller.

Write a program that will automatically control the brightness of a light based on the surrounding light level. Automatic Night Light.

1 Applied Control Systems Technology. 2 Pin configuration Applied Control Systems.

Measuring the Current and Voltage of a 820 Ω Resistor Setting for Multimeter = 200 mA DC Measure Voltage in 2 V increments up to 20 V.

Presentation of the DriveLab Board Opal-RT Real-time institute 2009.

REVISION A Thermaltake Commander Series Commander FX – 10 Port Fan Hub Works with all 3-pin fans.

Figure 1: ICD Single Channel Block Diagram Schematic PMT High Voltage Supply (see Figure 4 & 4a) LED Pulser PMT Calibration (see Figure 6) ICD Scintillator.

AUP2G57 configured as flip flop Dual Configurable Logic Design Contest.

The 3 parts of an electronic system are :

CLIQ unit Integration. General view: -Schroff rack 19’’ 25U (500mm x 600mm x 1120mm). -2 fixed wheels +2 castor wheels with brake ⦰100mm. Capacitors Capacitors.

Which of the signals below is a digital signal?

ELECTRONICS An electronics system has 3 parts – input, process, output.

Dupline Hi-Line Irrigation Control Jens Neigaard1.

Digital Electronics and Computer Interfacing Tim Mewes 5. Computer Interfacing – DAQ cards.

0-10V Ballast Dimmer HDL-MRDA HDL-MRDA channel 10A DC0 － 10V output module is a multifunction control module. It has 6 channel relay.

MRDA Wiring diagram S-BUS Module ID setting button ballast L N DC0-10V dimming voltage Control DC Maximum current :100mA 6 relay switch 16A 6 channel.

18240 Element two - Components INPUTS OUTPUTS PURPOSE TYPICAL USE.

6 CH 5A LED Dimmer HDL-MDLED /2/2016 Description HDL-MDLED CH 5A Intelligent LED Dimming Module, it can be used to control the LED.

ABB i-bus® EIB Shutter Actuators

Intro to USB-6009 DAQ.

USB DAQ Product Introduction

Room Controller RC/A 8.1 Room Controller economic flexible modular.

ABB i-bus® KNX Light Controller LR/S x.16.1 with LF/U 2.1.

AA/S 4.1 Analogue Actuator AAM/S 4.1 Analogue Actuator Module

System Network Structure

LED - Infrared 850nm Description: This is a very simple, clear infrared LED. These devices operate between nm and work well for generic IR systems.

Dimmer 6fold 10V Actuator M/DA

음향 시스템 사양서 POWER SUPLY WITH 3.5 PHOENIX CONNECTOR AMX: PSN6.5

Universal Interface, 4-fold, FM, US/U 4.2

ABB i-bus® EIB Display and Control Tableau

ABB i-bus® KNX The new Room Master RM/S 3.1 and RM/S 4.1

Block Diagram Transmitter Receiver × 2 Transmitter Power Supply ADC

Interfacing different devices & considerations

Transistor & Voltage Divider

Latches and Flip-flops

ABB i-bus® EIB / KNX Binary Input BE/S x.x.1

Multi Channel Interface & Basic Amplifier

McCrometer Nano Board Test Procedure

2 channels, each as input or output

Electronic relay ER/U 1.1 contact TU/W 1.1 US/U 4.1 ER/U 1.1

Multi Channel Interface & Basic Amplifier

Universal Interface, 12-fold, FM US/U 12.2

Universal I/O Concentrator UK/S 32.2

ULT Product Update New M2 Modules.

ABB i-bus® EIB / KNX Data Logging Unit BDB/S 1.1

CrystaLatchTM High Power 1x1,1x2 Solid-State Fiberoptic Switch (5W CW)

CrystaLatchTM 1x1,1x2, Solid-State Fiberoptic Switch

CrystaLatchTM 1x8 Fiberoptic Switch

CrystaLatchTM Mini 1x3,1x4 Solid State Fiberoptic Switch

Performance Specifications

CrystaLatchTM 1x1, 1x2, Solid-State Fiberoptic Switch

CrystaLatchTM Bi-Directional 1x1,1x2 Solid-State Fiberoptic Switch

CrystaLatchTM 1x2 PM Bidirectional Fiberoptic Switch

CrystaLatchTM 1x2 Multicasting Solid-State Fiberoptic Switch

CrystaLatchTM Single Stage 2x2 Series Fiber Optical Switch

CrystaLatchTM 1x16 Bidirectional Solid State Fiberoptic Switch

Performance Specifications

Performance Specifications

Performance Specifications

CrystaLatchTM 1x4 Fiberoptic PM Switch

DC-20KHz Driver for NanoSpeedTM VOA (patents pending)

CrystaLatchTM Mini 1x3,1x4 Solid State Fiberoptic Switch

Performance Specifications

CrystaLatchTM 1x1,1x2, Solid-State Fiberoptic Switch

CrystaLatchTM 1x3,1x4 Solid State Fiberoptic Switch

Example Example 1: An electric lamp is rated 110 W, 200 V. When the lamp is operated at its rated power and voltage, calculate a) the current flowing through.

CrystaLatchTM Bidirectional 1x8 Solid State Fiberoptic Switch

Presentation transcript:

4 channels, each as input or output 6 cables with connection plug (30 cm long). Extenable up to 10 m Channel configured as Input: Scanning voltage 20 V pulsed Scanning current 0.5 mA Channel configured as Output: Output voltage 5 V DC Output current max. 2 mA limited via a series resistor Dimensions: (HxWxD) 39 x 40 x 12 mm

Application Program Only one Application-Software with all functions: Reaction to signal flanks (rising edge, falling edge,...) Transmission of switch- and / or dimming telegrams Shutter / Blind control Control of light-scenes including storage and recall Transmission of diverse value and data type telegrams Impulse counter Control commands for heating and cooling applications Display and indication (LED) ....