4.4 Section 4.4.

Slides:

Advertisements

Similar presentations

Section 5.3 Trigonometric Functions on the Unit Circle

Advertisements

Angles, Reference Angles, Unit Circle

Section 1.1 The Distance and Midpoint Formulas. x axis y axis origin Rectangular or Cartesian Coordinate System.

Trigonometric Functions on the

Terminal Arm Length and Special Case Triangles DAY 2.

Trigonometric Functions of General Angles Section 3.4.

Definition of Trigonometric Functions With trigonometric ratios of acute angles in triangles, we are limited to angles between 0 and 90 degrees. We now.

Chapter 3 Trigonometric Functions of Angles Section 3.3 Trigonometric Functions of Angles.

Using Trigonometric Ratios

Section 5.3 Trigonometric Functions on the Unit Circle

Warm-Up Make all units the same then solve for the missing side 32 in.

Sullivan Algebra and Trigonometry: Section 2.1 Rectangular Coordinates Objectives Use the Distance Formula Use the Midpoint Formula.

Sullivan Algebra and Trigonometry: Section 7.2 Objectives of this Section Find the Value of Trigonometric Functions of Acute Angles Use the Fundamental.

7.2 Right Triangle Trigonometry. A triangle in which one angle is a right angle is called a right triangle. The side opposite the right angle is called.

Section Recall Then you applied these to several oblique triangles and developed the law of sines and the law of cosines.

Chapter 6 – Trigonometric Functions: Right Triangle Approach Trigonometric Functions of Angles.

Trigonometric Functions: The Unit Circle & Right Triangle Trigonometry

3-3 The Coordinate Plane ► Standard (P5) I will be able to plot points in the coordinate plane ► Fold and cut ordered pair and coordinate plane foldable,

Table of Contents 3. Right Triangle Trigonometry.

3.4 Circular Functions. x 2 + y 2 = 1 is a circle centered at the origin with radius 1 call it “The Unit Circle” (1, 0) Ex 1) For the radian measure,

8-1 Standards 8a - Draw angles that are negative or are larger than 180° 8b - Find the quadrant and reference angles of a given angle in standard position.

Coordinate Trigonometric Definitions If P(x, y) is any point on the terminal side of an angle in standard position and r is the distance of P from the.

Chapter 5 Section 5.2 Trigonometric Functions. Angles in Standard Position Recall an angle in standard position is an angle that has its initial side.

Trigonometric Functions: The Unit Circle Section 4.2.

TRIGONOMETRY – Functions 1 We will now place the angle in the x–y plane. The initial side of the angle will always be placed on the (+) side of the x –

TRIGONOMETRY FUNCTIONS OF GENERAL ANGLES SECTION 6.3.

The Coordinate Plane. We have worked with both horizontal and vertical number line s Horizontal

Section 4.4 Trigonometric Functions of Any Angle.

TRIGONOMETRIC FUNCTIONS OF ANY ANGLE

6.3 Trig Functions of Angles

Trigonometric Functions of Any Angle

TRIGONOMETRY FUNCTIONS

Midpoint and Distance in the Coordinate Plane

Section 1-6 Midpoint and Distance in the Coordinate Plane

Table of Contents 5. Right Triangle Trigonometry

Chapter 2 Trigonometry.

Introduction to Trigonometry

Copyright © 2017, 2013, 2009 Pearson Education, Inc.

COORDINATE GRAPHING.

Do Now: A point on the terminal side of an acute angle is (4,3)

Introduction to the coordinate Plane

Rectangular Coordinates;

Reference Angles & Unit Circle

Pythagorean Theorem and Distance

Graphing / Plotting Points Review

Evaluating Trigonometric Functions

The Coordinate Plane By: Christine Berg Edited By:VTHamilton.

Cartesian Coordinate System

Mrs. Volynskaya Pre-Calculus Chapter 4 Trigonometry

P.5 The Cartesian Plane Our goals are to learn

Evaluating Trigonometric Functions

Define General Angles and Radian Measure

Chapter 1: Lesson 1.1 Rectangular Coordinates

Find sec 5π/4.

The Distance and Midpoint Formulas

Warm Up Write answers in reduced pi form.

The Coordinate Plane By: Christine Berg Edited By:VTHamilton.

Introduction to Trigonometry

Graphing in the Coordinate Plane

Objective - To graph ordered pairs on the coordinate plane.

The Distance and Midpoint Formulas

Circular Trigonometric Functions.

Sullivan Algebra and Trigonometry: Section 2.1

Reference Angles.

How do we draw angles in standard position?

The COORDINATE PLANE The COORDINATE PLANE is a plane that is divided into four regions (called quadrants) by a horizontal line called the x-axis and a.

3.4 Circular Functions.

Trigonometry Extended: The Circular Functions

Graphing Ordered Pair – gives the location of a coordinate point

Presentation transcript:

4.4 Section 4.4

Trigonometric Functions of Any Angle If you are given an ordered pair that is not on the Unit Circle, then you need to plot the point. From the point you plotted, make a right triangle. Draw a vertical line from the point to the x-axis. Draw a diagonal line from the point to the origin.

Trigonometric Functions of Any Angle Label the x-coordinate on the x-axis and the y-coordinate on the side of the triangle that is vertical. Theta goes inside the triangle closest to the origin. Use Pythagorean Theorem to find the third side of the triangle. The hypotenuse is always positive.

Trigonometric Functions of Any Angle Use right triangle trigonometry to find the six trigonometric functions.

Reference Angles Reference Angles – the distance from the terminal side of the angle to the x-axis. Reference angles are always acute and always positive.

Reference Angles Quadrant I: Quadrant II: Quadrant III: Quadrant IV: