DILBERT.

Slides:



Advertisements
Similar presentations
FABRICATION PROCESSES
Advertisements

High Pressure Plasma with a third electrode James Roberts Physics TSP 2002 Supervised by Dr Kerrie Balla.
I have seen this happen !. You have exceeded your storage allocation.
Thermoforming Process
4-1 Chapter 4 Overview b The DCM is very complex Mechanical, electrical, hydraulic and safety systems all work together Mechanical, electrical, hydraulic.
Antenna Design - Review In antenna design, an important design parameter is the wavelength of the EM wave In antenna design, an important design parameter.
Northern Illinois University’s ion beam sputtering system for boron deposition on a CCD Donna, et al. 17May2013 Special thanks to Gregg Westberg (NIU)
Dilbert.
Photolithography Photolithography is the transfer of patterns, circuits, device structures, etc. to a substrate or wafer using light and a mask.
Vacuum Technology Need for Vacuum Environment
There are no FREE lunches. Anti-reflective coating A anti-reflective coating is deposited on the top side to help transmit more of the incident sunlight.
Varian 3118 Thermal Evaporation System
Top Side Conductor vacuum deposition Aluminum sputter deposit in Argon plasma CVC 601-sputter deposition tool.
The Deposition Process

Physical Vapor Deposition
ECE/ChE 4752: Microelectronics Processing Laboratory
INTEGRATED CIRCUITS Dr. Esam Yosry Lec. #5.
Thin Film Deposition Prof. Dr. Ir. Djoko Hartanto MSc
Center for Materials for Information Technology an NSF Materials Science and Engineering Center Vacuum Evaporation Lecture 8 G.J. Mankey
Photoelectron Spectroscopy Lecture 5 – instrumental details –General spectrometer design –Vacuum generation and measurement.
Pressure 1 atmosphere ~ 1 bar ~ 760 mm Hg ~ 760 torr ~ 100,000 Pa Ion gauges read in mbar i.e. 1x mbar = 1x atm. Sometimes ion gauges read.
Solar Cell conductive grid and back contact
Be careful what you wish for. SiO2 backside protection A coating of SiO2 is deposited on the backside of the wafer to insolate it from the doping process.
Methods in Surface Physics Experimentation in Ultra-High Vacuum Environments Hasan Khan (University of Rochester), Dr. Meng-Fan Luo (National Central University)
Vacuum science.
VTS Sputter Roll Coater
Nano/Micro Electro-Mechanical Systems (N/MEMS) Osama O. Awadelkarim Jefferson Science Fellow and Science Advisor U. S. Department of State & Professor.
Dilbert. Next steps in the antenna fabrication process Create a dielectric surface. The antenna must sit on a dielectric or insulating surface,
Techniques of Vacuum and Basics of High Voltage (2/3) Pauli Heikkinen Jyväskylä University.
SEMINAR ON IC FABRICATION MD.ASLAM ADM NO:05-125,ETC/2008.
Vacuum system.
Vacuum Fundamentals 1 atmosphere = 760 mm Hg = kPa 1 torr = 1 mm Hg vacuum range pressure range low 760 ~ 25 torr medium 25~ high ~ 10.
High-Vacuum Technology Course
DILBERT. Did research and learned about several communication devices – cellular phones, Bluetooth/Wi-Fi, and RFID Did research and learned.
Matter and Atomic Structure Section 3.3- State of Matter
Antenna Design - Review In antenna design, an important design parameter is the wavelength of the EM wave Wavelength is a function of frequency Antenna.
Vacuum Technology.
Top Down Method Vacuum Applications in Nanomanufacturing Author’s Note: Significant portions of this work have been reproduced and/or adapted with permission.
Substitute beer and pizza?. Basic Silicon Solar Cell as fabricated in Cameron With Schematic.
Solar Cells need a top side conductor to collect the current generated They also need a conductive film on the backside.
Vacuum Fundamentals Top Down Method Vacuum Technology Basics Author’s Note: Significant portions of this work have been reproduced and/or adapted with.
Section 5: Thin Film Deposition part 1 : sputtering and evaporation
Antenna Project in Cameron clean room Wafer preparation, conductor deposition, photolithography.
Jari Koskinen 1 Thin Film Technology Lecture 2 Vacuum Surface Engineering Jari Koskinen 2014.
NIU’s ion beam deposition system for boron deposition on a CCD Donna 9May2013.
Solar Cells need a top side conductor to collect the current generated They also need a conductive film on the backside.
Vacuum Systems for Electron Microscopy Constraints on Specimens Specimens placed in the electron microscope must be able to withstand very high vacuum.
Holders and Pumps Summary
DC Sputtering Disadvantage #1 Low secondary electron yield
Photolithography Photolithography is the transfer of patterns, circuits, device structures, etc. to a substrate or wafer using light and a mask.
Dilbert.
© 1997, Angus Rockett Section I Evaporation.
Jari Koskinen, Sami Franssila
DOE Plasma Science Center Control of Plasma Kinetics
Thermoforming Process
PVD & CVD Process Mr. Sonaji V. Gayakwad Asst. professor
Electron-Beam Machining
-Honors Thesis Defense- In Situ Ellipsometry of Surfaces in an Ultrahigh Vacuum Thin Film Deposition Chamber Joseph Choi Department of Physics and Astronomy,
It’s what the world is made of.
1.6 Glow Discharges and Plasma
Antenna Design - Review In antenna design, an important design parameter is the wavelength of the EM wave Wavelength is a function of frequency Antenna.
Antenna Design - Review In antenna design, an important design parameter is the wavelength of the EM wave Wavelength is a function of frequency Antenna.
IC AND NEMS/MEMS PROCESSES
BONDING The construction of any complicated mechanical device requires not only the machining of individual components but also the assembly of components.
Laboratory: A Typical Oxidation Process
Antenna Design - Review In antenna design, an important design parameter is the wavelength of the EM wave Wavelength is a function of frequency Antenna.
Molecular Beam Epitaxy
Basic Planar Process 1. Silicon wafer (substrate) preparation
Presentation transcript:

DILBERT

Summary of Project to Date Did research and learned about several communication devices – cellular phones, Bluetooth/Wi-Fi, and RFID Received silicon wafer to be used as base for antennas – could use other substrates if equipment was available Received a traveler defining the steps necessary to fabricate your antenna Cleaned silicon wafers to provide a contamination free surface Grew SiO2 (silicon dioxide) to provide an insulating dielectric surface Determined your application, either cellular, Bluetooth/Wi-Fi, or RFID Determined how to find the correct length for the antenna based on the application Using a decision matrix determined the conductor to be used to fabricate the antenna This week will deposit conductor of choice

Thin Film Deposition Conductors are deposited using a vacuum chamber The vacuum chamber reduces the atmosphere to high vacuum levels (no atmosphere) This reduces contaminating the films, provides a non-contaminating environment free of oxygen, water vapor, etc. and allows materials to melt at lower temperatures.

Thin Film Deposition Thin film deposition tools are very complex due to the need to create high vacuum levels. Vacuum levels of 5x10-7 torr and better are typical. Sea level atmospheric pressure is about 740 torr or 7.4x102 Because of their complexity, vacuum chambers are very expensive.

Thin Film Deposition To achieve high vacuum levels, several types of vacuum pumps are used. Mid level vacuum levels (2x10-3 torr) are reached with rotary vane vacuum pumps. These pumps are also know as mechanical or roughing vacuum pumps High level vacuum levels are reached using Diffusion vacuum pumps – requires liquid nitrogen to prevent oil contamination Turbomolecular pumps – like a small jet engine, clean and fast, good for processes that require the introduction of a process gas. Because of the high speed vanes, subject to catastrophic failure Cryogenic vacuum pumps – uses low temperature (10oK) – also clean and fast pumping but requires regeneration periodically which is time consuming

Thin film deposition tools in the ECE Microelectronics Clean Room Cooke-thermal deposition CVC 601-sputter deposition CHA Mark 50 e-beam deposition Varian 3125 e-beam deposition

Conductor Deposition The Cooke thermal evaporator is not currently used. The CVC sputter tool is used only for aluminum depositions. Only an aluminum target is available. The Varian 3125 and CHA Mark 50 e-beam deposition tools are used for all other conductors, Cu, Au, Ag, Cr, Ni An e-beam evaporates material, it get the material so hot it becomes a gas and evaporates. It then travels in a straight line, because it is under vacuum, until it condenses when it strikes a colder surface

With sputtering, an Argon plasma is formed, causing argon ions to strike a metal target and knock loose material. Because an electric field is created, material is deposited on the substrate Argon plasma – ionized argon in an electric field Material target Substrate to be coated

E-beam Evaporation uses a high energy electron beam to vaporize (change from a solid to vapor) materials, especially metals

Overall view of the Varian 3125 vacuum chamber Overall view of the Varian 3125 vacuum chamber. This tool deposits thin films using e-beam evaporation

Portion of Varian 3125 control rack

Varian 3125 quartz heater controller, shutter controller and planetary rotation controller E-beam shutter controller Planetary (wafer holder) rotation controller

Electron beam power supply Electron beam can be steered by magnetic fields Typically 6-8KV are required to form the electron beam

Cryopump temperature-must be below 15oK

Varian 3125 ion gauge controller and deposition controller

Varian 3125 view of open chamber Wafer planetary – can rotate or stay stationary. Can be removed for loading

Varian 3125 4-pocket e-beam crucible

With an e-beam (electron beam) evaporator the material is heated to a vapor (gas) and then condenses on cooler surfaces Substrates (wafers) sit at the top of the chamber Electron beam is formed and strikes the metal crucible Molten material hot enough to vaporize (become a gas)

Varian 3125 wafer planetary Wafer planetary for Varian 3125

Wafers are held down by spring clips Varian 3125 Wafers are held down by spring clips

Varian 3126 Quartz Heaters

Varian 3125 door showing glasds slide holder Glass slide must be replaced before each run

Overall view of the CHA Mark 50 vacuum chamber Overall view of the CHA Mark 50 vacuum chamber. This tool deposits thin films using e-beam evaporation

Inside of CHA Mark 50 chamber showing wafer platen – can not be removed from the chamber

CHA Mark 50 wafer adapter ring Adapter ring for 4”/100mm wafer Adapter rings are available for 2”, 3” and 4” wafers

CHA Mark 50 4-pocket e-beam crucible Four different materials are available to do sequential evaporations

CHA Mark 50 crucible materials and chamber temperature monitor Materials currently inside the 4 pocket crucible are shown with their pocket number Pocket is chosen using this indexer

CHA Mark 50 crystal oscillators for evaporation material thickness measurement

New glass slides must be used for each evaporation

CHA Mark 50 cryo-pump control Cryogenic pump temperature – should be less than 15oK

CHA Mark 50 vacuum gauge controller Vacuum chamber pressure of 7.5 x 10-7 torr

CHA Mark 50 E-beam power supply and controller High voltage switch and current control Power supply main on/off switch Power supply is interlocked to prevent activation if vacuum pressure, cooling water, and zero current conditions are not met

Crucible being heated by an electron beam E-beam evaporation Crucible being heated by an electron beam

Overall view of the CVC vacuum chamber Overall view of the CVC vacuum chamber. This tool deposits thin films using “sputtering”

CVC sputter tool with chamber lid open Wafers are loaded into position

Looking into the CVC sputter tool chamber, showing the 8” aluminum target

CVC sputter tool control racks Ion gauge

Argon MFC – 30 sccm flow typical Cryo pump temperature – must be below 16oK

CVC sputter tool DC power supply for aluminum target DC Voltage about 4KV DC current 0.5 to 1.0 A

CVC sputter tool view port

View of argon sputter plasma in CVC sputter tool

View of argon plasma in AJA sputter tool Sputter target Shutter Substrate (wafer) stage Wafer stage can rotate and heat

Homework Assignment Due next class meeting Review “Mask design steps” from web site Read “Designing Antennas for Cellular Telephones” from web site. Find “AutoCad” on Mosaic – listed under Mechanical Engineering as AutoCad 2006 Become familiar with AutoCad. There is a tutorial on my web site Begin preliminary dimension sketches for your antenna design Maximum size 20mmx20mm Minimum size 5mmx5mm Line width – 1mm Spacing between lines – 1mm or greater No sharp corners Must be able to fit inside a box to allow cutting into individual antenna Length must match your design length Can be any design – be creative Dimension drawing of your design is required

Simple spiral design

Cingular Logo design

XBOX design Note-DO NOT USE WHITE ON BLACBACKGROUND

Football Design- DO NOT USE WHITE ON DARK BACKGROUND

UNC-Charlotte Crown design

Dimensions not in a contrasting color