Exercises for Q1. Insulated copper tube A thin walled 10 mm copper tube is used to transport a low-temperature refrigerant with a temperature that is.

Slides:

Advertisements

Similar presentations

Conduction Conceptests

Advertisements

Quiz – An organic liquid enters a in. ID horizontal steel tube, 3.5 ft long, at a rate of 5000 lb/hr. You are given that the specific.

Application of Steady-State Heat Transfer

ERT 216 HEAT & MASS TRANSFER Sem 2/

ME 340 Project: Fall 2010 Heat Transfer in a Rice Cooker Brad Glenn Mason Campbell.

Chapter 3c : One-dimensional, Steady state conduction (with thermal energy generation) (Section 3.5 – Textbook) 3.1 Implications of energy generation Involve.

So Far: Conservation of Mass and Energy Pressure Drop in Pipes Flow Measurement Instruments Flow Control (Valves) Types of Pumps and Pump Sizing This Week:

Matter and Energy.

Heat Transfer Chapter 2.

Chapter 2: Overall Heat Transfer Coefficient

Operational Principle of Thermal Bubble Jet injected droplet heater bubble Chamber neck liquid Current pulse heats up liquid Bubble as a pump pushes out.

Chapter 2: Steady-State One-Dimensional Heat Conduction

Analysis of Simple Cases in Heat Transfer P M V Subbarao Professor Mechanical Engineering Department I I T Delhi Gaining Experience !!!

One-Dimensional Steady-State Conduction

Example 1:- An annular alloyed aluminum (k = 180 W/m . K ) fin of rectangular profile is attached to the outer surface of a circular tube having an outside.

CHE/ME 109 Heat Transfer in Electronics LECTURE 7 – EXAMPLES OF CONDUCTION MODELS.

LINEAR SECOND ORDER ORDINARY DIFFERENTIAL EQUATIONS

Heat exchangers. Device that facilitate the exchange of heat between fluids that are at different temperatures while keeping them from mixing with each.

CONDUCTION HEAT TRANSFER gjv

Conduction & Convection.

HEAT TRANSFER IN LIGHTSABERS An ME 340 Project by Clayton Grames.

Examples and Problems.

Internal Flow Convection -constant surface temperature case Another commonly encountered internal convection condition is when the surface temperature.

CBE 150A – Transport Spring Semester 2014 Heat Transfer Introduction.

Lab-1,Week 1, EML 3016 C- Spring 2003 Electronic Device Cooling A thin (assume zero thickness) electronic chip has a square shape of an area 5x5 cm 2,

Armaflex Solutions For Heating and Plumbing. Heating and Plumbing 2 Insulation main target: Limit heat losses (energy savings) Noise control Condensation.

STEADY HEAT TRANSFER AND THERMAL RESISTANCE NETWORKS

Fouling Factor: After a period of operation the heat transfer surfaces for a heat exchanger become coated with various deposits present in flow systems,

ISAT Module III: Building Energy Efficiency

Overall Heat Transfer Coefficient

Heat Transfer Equations For “thin walled” tubes, A i = A o.

Chapter 3 Part 1 One-Dimensional, Steady-State Conduction.

So Far: Conservation of Mass and Energy Pressure Drop in Pipes Flow Measurement Instruments Flow Control (Valves) Types of Pumps and Pump Sizing This Week:

Armaflex Solutions High Temperature and Solar Installations.

Remember... Resistance in Mechanical systems (friction) opposes motion of solid objects.

ERT 216 HEAT & MASS TRANSFER Sem 2/

One-Dimensional Steady-State Conduction

Pharos University جامعه فاروس Faculty of Engineering كلية الهندسة Petrochemical Department قسم البتروكيماويات PE 330 ENERGY CONSERVATION LECTURES (6-7)

JCOV, 25 OCT 2001Thermal screens in ATLAS Inner Detector J.Godlewski EP/ATI  ATLAS Inner Detector layout  Specifications for thermal screens  ANSYS.

Master’s of Engineering Project Fall 2010 Viram Pandya.

Equipment Design Designed by Eman A. Khajah. Outline Design of Heater. Design of Stripper.

Heat Transfer Equations. Fouling Layers of dirt, particles, biological growth, etc. effect resistance to heat transfer We cannot predict fouling factors.

Conduction C ontents: Basic Concept Example Whiteboards.

Heat Transfer Equations For “thin walled” tubes, A i = A o.

Fourier's law of heat conduction

Thermal Analysis Assumptions: Body Temperature (Environment) is 37˚C Heat distribution on outside of device will be modeled via FEA Heat transfer method.

Cooling of GEM detector CFD _GEM 2012/03/06 E. Da RivaCFD _GEM1.

Unit 42: Heat Transfer and Combustion

Date of download: 5/28/2016 Copyright © ASME. All rights reserved. From: Forced Convection Heat Transfer in Spray Formed Copper and Nickel Foam Heat Exchanger.

Introduction 1 Heat Transfer and Its Applications.

TUTORIAL 1 7/3/2016.

1-D conduction through cylinders

Heat Transfer 传热学 Li xuemei Welcome to.

Lesson 7: Thermal and Mechanical Element Math Models in Control Systems ET 438a Automatic Control Systems Technology 1lesson7et438a.pptx.

One-Dimensional Steady-State Conduction

THERMAL LOADING OF BUILDINGS

14-6 Heat Transfer: Conduction

Conservation of Mass and Energy

Building Energy Analysis

Chapter Three Sections 3.1 through 3.4

ET 438a Automatic Control Systems Technology

Additional Examples (From the Text book)

Conduction thermal resistance in different coordinate system

What is Fin? Fin is an extended surface, added onto a surface of a structure to enhance the rate of heat transfer from the structure. Example: The fins.

Heat Exchangers Heat Exchangers.

Example (3): Steam flowing through a long, thin-walled pipe maintains the pipe wall at Uniform temperature of 500 k. the pipe is covered with an insulation.

Steady-State Heat Transfer (Initial notes are designed by Dr

Steam traps Applications and Recommendations

What are Fins ? Fins are extended surfaces used to increase the rate of heat transfer. It is made of highly conductive materials such as aluminum.

Presentation transcript:

Exercises for Q1

Insulated copper tube A thin walled 10 mm copper tube is used to transport a low-temperature refrigerant with a temperature that is less than that of the ambient air (convection coefficient of 5 W/m 2 -K). The temperature difference is about 200 K. What is the heat transfer rate, total thermal resistance if the tube is insulated with 0, 5 10, 15, 20 mm thick of cellular glass material (k = 0.05 W/m-K)? What is the overall heat transfer coefficient based on the outside surface area if the tube has 6-mm thick insulation?

Critical radius of insulation Derive the critical radius of insulation for an insulated steam pipe in terms of the thermal conductivity of the insulating material and the outside convective heat transfer coefficient.

Containment of radioactive waste Radioactive waste (k = 20 W/m-K) are stored in a 10 cm thick spherical stainless steel (k = 15 W/m-K) container of inner radius r i = 0.5 m. Heat is generated volumetrically within the waste at a uniform rate of 10 5 W/m 3, and the outer surface of the container is exposed to a water flow for which the bulk temperature is 25 o C and the convective heat transfer coefficient is 1000 W/m 2 -K. Determine the maximum temperature in the radioactive waste. Ans. 338 C