STEEL DESIGN KNOWLEDGE BASE REQUIRED: STRENGTH OF MATERIALS STEEL DESIGN REVIEW OF TIMBER DESIGN BEARING PROBLEM TIMBER DESIGN SOIL MECHANICS REVIEW OF SOIL MECHANICS vertical stresses lateral stresses

LECTURE #4(CONT) BASIC SOIL MECHANICS REVIEW: = - VERTICAL STRESSES: = VERTICAL STRESS (PSF, TSF,KN/m 2 ) CALCULATE TOTAL LATERAL STRESS, (TOTAL STRESS) Ka=0.307 (EFFECTIVE STRESS) q=100 kPa or KN/m 2 Draw stress diagram, calculate resultant & location CLASS PROBLEM:

LECTURE #4(CONT) BASIC SOIL MECHANICS REVIEW: LATERAL STRESSES: 30.7KN/m KN/m 2

LECTURE #4(CONT) BASIC SOIL MECHANICS REVIEW: LATERAL FORCE: 30.7KN/m KN/m KN 30.98KN R= =138.43KN KN 1.62m

LECTURE #4(CONT) BASIC STEEL DESIGN REVIEW: Review of AISC Construction Manual (cont): Compact vs. Non- Compact Compact Beam are rolled beam that can achieve the plastic moment. Stress Distribution of I Beam

LECTURE #4(CONT) BASIC STEEL DESIGN REVIEW: Review of AISC Construction Manual (cont): Compact Sections- are symmetrical about the y-y axis webs/flanges must have certain width-thickness ratios (Spec Section - Table B5.1,P.5-36) compression flange must be adequately braced against lateral buckling When the theoretical yield stress F’y is equal to or exceeded by the yielding stress than the section is no longer compact.

LECTURE #4(CONT) BASIC STEEL DESIGN REVIEW: Design Procedure for Bending(using Sx) 1. Determine the Maximum Bending Moment 2. Compute the Required Section Modulus based on allowable stresses Fb=.66Fy (compact) [equat. F1-1,Chapt. F1.1] or Fb=.60 Fy (for non compact)[equat. F1-5,Chapt. F1.2] 3. Enter the ASD selection table and find the nearest tabulated value of Sx. The lightest weight and the most economical section that will serve for the yield strength stated is in bold face, and should be selected adjacent to or above the required Sx. 4. Check F’y column to be sure of compact section. 5. Check the lc & lu to make sure of adequate bracing.

LECTURE #4(CONT) BASIC STEEL DESIGN REVIEW: Note:For Members with Compact or Non-compact sections. Recall lc is the max. unbraced length in feet of the compression flange at which the allowable bending is taken at 0.66 Fy Recall lu is the max. unbraced length in feet of the compression flange for which allowable bending stress may be taken at 0.60 Fy when Cb=1

LECTURE #4(CONT) BASIC STEEL DESIGN REVIEW: Recall l, lc, and lu if l is the given length between lateral supports then, lc>l use Fb=.66Fy (assuming compact section) lu>l>lc use Fb=.60Fy l>lu use the charts of allowable moments in beams (p to 2-212) where Cb=1 Note: Cb is the bending coefficient dependent upon moment gradient (F1.3) Cb=1 when the bending moment at any point within an unbraced length is larger than that at both ends of this length when frames are braced against joint translation. when considering a conservative value for cantilever

LECTURE #5 BASIC STEEL DESIGN REVIEW: Given: Select a beam of Fy=36ksi steel subjected to a bending moment of 125 kip-ft., having its compression flange braced at 6 ft. intervals. Solution: Assume compact section, Fb=0.66Fy=23.8ksi 1. Maximum Bending Moment Given in Problem 2. Sx(reqd)=M/Fb=(125x12)/23.8=63 cu.in. 3. Nearest Tabulated Value W16x W12x Since W16x40 is bold face, it is the lightest suitable section that will serve for that yield strength.

LECTURE #5 BASIC STEEL DESIGN REVIEW: Given: Select a beam of Fy=36ksi steel subjected to a bending moment of 125 kip-ft., having its compression flange braced at 6 ft. intervals. 5. From the table, Lc=7.4 ft. >6.0 ft. so the bracing is adequate and the assumed allowable stress of.66Fy is correct. Use W16x40 Solution contd: 4. A check of the F’y column shows a dash, indicating that F’y is greater than 65 ksi. Therefore, the shape is compact.

LECTURE #5(CONT) BASIC STEEL DESIGN REVIEW: Design Procedure for Bending(using Mr) 1. Enter the ASD selection table and find the nearest tabulated value of Mr. The lightest weight and the most economical section that will serve for the yield strength stated is in bold face, and should be selected adjacent to or above the required Mr. Recall: Mr is the beam resisting moment if shape has non compact flanges if shape has compact sections

LECTURE #5 BASIC STEEL DESIGN REVIEW: 2. Check F’y column to be sure of compact section. 3. Check the lc & lu to make sure of adequate bracing. Given: Select a beam of Fy=36ksi steel subjected to a bending moment of 125 kip-ft., having its compression flange braced at 6 ft. intervals. Solution: Assume compact section, Fb=0.66Fy=23.8ksi 1. Enter Bending Moment Given in Problem Nearest Tabulated Value W16x k-ft W12x k-ft Since W16x40 is bold face, it is the lightest suitable section that will serve for that yield strength.

LECTURE #5 BASIC STEEL DESIGN REVIEW: 3. Check F’y column to be sure of compact section. OK the same as before 4. Check the lc & lu to make sure of adequate bracing. Lc=7.4ft > 6.0ft therefore Mr is valid Given: Select a beam of Fy=36ksi steel subjected to a bending moment of 125 kip-ft., having its compression flange braced at 6 ft. intervals. Use W16x40