1. 1 * * * Updated for NTS software version 4.1.30, 2011-07-01 * * *

2. 2 Part 3 Registration Workstation Configuration and Set-up Note: All NTS logins are held by your local NTS administrator, contact them for the user names and passwords (anything labeled “Entry #1”, “Entry #2”, “Entry #3”, etc.)

3. 3 Registration Workstation Setup Note: “Administrator” access required to perform this task. 1.When “warning banner” appears, on keyboard, press and hold Shift then Enter. The NTS Log-in pops up. 2.Put Entry #1 for “user name” and Entry #2 for the “password” (get from NTS admin) 3. Select OK.

4. 4 Registration Workstation Setup Note: “Administrator” access required to perform this task. 4.On the next pop- up, select OK.

5. 5 Registration Workstation Setup Note: “Administrator” access required to perform this task. 5.In the Encryption Plus pop-up put Entry #3 for “user name” (enter twice) and Entry #4 for “password” (enter twice). 6.Select Next

6. 6 7.Select Next 8.Select Hide on final Encryption pop-up. Registration Workstation Setup Note: “Administrator” access required to perform this task. 9. Restart Computer

7. 7 Registration Workstation Setup Note: “Administrator” access required to perform this task. After laptop restarts…the screen below appears. THEN…

8. 8 Registration Workstation Setup Note: “Administrator” access required to perform this task. Next screen appears Press Enter on keyboard. Put Entry #3 for “user name” Put Entry #4 for “password”

9. 9 Registration Workstation Setup Note: “Administrator” access required to perform this task. 1.When “warning banner” appears, on keyboard, press and hold Shift then Enter. The NTS Log-in pops up. 2.Put Entry #1 for “user name” and Entry #2 for the “password” (get from NTS admin) 3. Select OK.

10. 10 1. 1. 2. 2. 3. 3. 4. 4. Right Click 5. 5. Click Select Set Wireless IP for ECC Registration Workstation (Hardware)

11. 11 Set Wireless IP for ECC Registration Workstation (Hardware) 6. 6. Select 7. 7. Select New Pop-up

12. 12 Set Wireless IP for ECC Regis- tration Workstation (Hardware) 10. 2. 2. 2 Type in Note: 10.2.2.1 is IP for server 255. 255. 255. 0 Remains same for all Select Note: Standardized CNFJ IP Numbering Convention Local Server: 10.2.2.1 Registration Workstation 1: 10.2.2.2 Registration Workstation 2: 10.2.2.3 Registration Workstation 3: 10.2.2.4 Registration Workstation 4: 10.2.2.5

13. 13 Set Wireless IP for ECC Registration Workstation (Hardware) Select Wireless is now connected. CloseCancel The next screen appears.

14. 14 Registration Workstation Setup (Software) 1.Click NTS Setup Icon on Workstation Desktop to open Setup Screen below. Note: Disregard Steps 1 through 8. Start at Step 9

15. 15 Registration Workstation Setup (Software) 3.Select NTS 4 Workstation. 4.Enter Local Server’s Wireless IP Address written down during Local Server setup. If no Wireless IP Address recorded, re-open Local Server’s Setup Screen and record IP Address displayed 10. 2. 2. 1

16. 16 10. 2. 2. 1 NTS version 4. x workstation enabled! Registration Workstation Setup (Software) 5.Select Apply.. Select OK. 6.Confirmation message will pop up after a few minutes as shown below. Select OK. 7.Close NTS 4.1 Setup, and then select NTS/ETAS Version 4 Icon on desktop to open application

17. 17 Configure Registration Workstation Select 1.Double-click the NTS/ETAS Version 4 Icon to open application 2.Log in via login screen.

18. 18 Configure Registration Workstation 4.Select Save. 3.Configure Workstation screen displays, as shown below. Select Approve Workstation box.

19. 19 5.A confirmation screen will display Configure Registration Workstation Select 6.Next screen appearing is the Welcome OIC screen. 7.This Workstation is ready for operations. 8.Repeat procedures on remaining workstations.