Presentation is loading. Please wait.

Presentation is loading. Please wait.

C2: Force, Motion and Energy

Similar presentations


Presentation on theme: "C2: Force, Motion and Energy"— Presentation transcript:

1 C2: Force, Motion and Energy
TEK 6.9C 8.3B 11-5 In the diagram above, a wind turbine is transforming energy from the wind. Between which two steps in the diagram is mechanical energy being converted into electrical energy? A) 1 and 2 B) 2 and 3 C) 3 and 4 D) 4 and 5

2 C2: Force, Motion and Energy
TEK 8.6C 8.2E 11-6 In a series of controlled experiments, a student measures the force acting on a wheeled cart and the cart’s acceleration. The student’s data are shown. Based on the recorded observations, what is the mass of the cart in kilograms?

3 C2: Force, Motion and Energy
TEK 8.6A 11-7 A toy train engine rests motionless on a track. One student begins pushing the engine to the right with a force of 2 newtons. At the same time, another student begins pushing the engine to the left with a force of 5 newtons. Which of the following best describes the resulting motion of the engine? A) It travels left at a constant speed. B) It travels left at an increasing speed. C) It travels right at a constant speed. D) It travels right at an increasing speed

4 C2: Force, Motion and Energy
TEK 8.6B 8.3B 13-3 The three vehicles are all traveling at a speed of 15m/s, but only the pickup truck has a changing velocity. The pickup truck has a changing velocity because the pickup truck — A) Can accelerate faster than the other two vehicles B) Is traveling in the opposite direction from the other two vehicles C) Is traveling on a curve in the road D) needs a large amount of force to move

5 C2: Force, Motion and Energy
TEK 7.7A 8.2E 13-7 Two boxes and their masses are shown. Which of the following situations shows work being done? A) A student is sitting in a chair and holding both boxes. B) A student is holding the large box 1 m above the floor. C) A student is standing and holding the small box. D) A student is lifting the small box 0.5m from the floor to a table.

6 C2: Force, Motion and Energy
TEK 8.6A 8.2E 13-10 For an investigation, a student measures the speed of a cart as it rolls down a ramp. The student then records data in the table. Which of these best explains the student’s data? A) The speed of the cart decreases as the cart rolls down the ramp because of friction between the cart and the ramp. B) The speed of the cart increases as the cart rolls down the ramp because the force acting on the cart is greater than the force of gravity. C) The speed of the cart increases as the cart rolls down the ramp because the forces acting on the cart are unbalanced. D) The speed of the cart decreases as the cart rolls down the ramp because the forces acting on the cart are balanced.?

7 C2: Force, Motion and Energy
TEK 8.6C 13-14 Two cars with different masses travel at the same speed down a hill toward a stop sign. What will happen when both cars apply brakes at the same time to stop? A) The car with the smaller mass will require less force to stop than the car with the larger mass. B) The car with the larger mass will maintain its velocity while traveling down the hill. C) The car with the smaller mass will take longer to stop than the car with the larger mass. D) The car with the larger mass will have less inertia than the car with the smaller mass.

8 C2: Force, Motion and Energy
TEK 6.8A 13-19 In a demonstration, a rubber ball is dropped from Position 1. The ball bounces as shown. At which position does the ball have both the greatest kinetic energy and the least potential energy?

9 C2: Force, Motion and Energy
TEK 8.6C 8.2E 13-22 Four students raced toy cars on a track. The mass and the acceleration of each car is recorded in the table. Which toy car had the greatest applied force?

10 C2: Force, Motion and Energy
TEK 6.8D 8.2D 13-28 A car travels at a constant speed of 15m/s for 2 minutes. The car increases its speed from 15m/s to 25m/s during the next minute and then travels at a constant speed of 25m/s for 2 more minutes. Which of the following graphs best represents the car’s motion during this 5-minute period?

11 C2: Force, Motion and Energy
TEK 6.8C 8.2E 13-30 A student walks 2 km in 30 minutes. What is the student’s average speed in km/h?

12 C2: Force, Motion and Energy
TEK 8.6A 8.2E 13-36 Some students measure the acceleration of a wheeled cart being acted on by varying forces. The students record their data in the table above. According to the data table, how much force is acting on the cart when the students measure an accelerationof2.6m/s2? A) 13N B) 7N C) 8N D) 12N

13 C2: Force, Motion and Energy
TEK 6.9C 8.3B 13-39 The diagram shows a hot air balloon rising. Propane gas tanks are seen at the bottom of the balloon. What energy transformations occur when propane gas is used to lift the balloon?

14 C2: Force, Motion and Energy
TEK 8.6C 8.3B 13-41 Sometimes tectonic plates do not move easily past one another, and the plates become stuck. Forces build up, and when the plates finally move, tension is released, as shown below. The sudden movement of plates is caused by – A) the mass of the plates B) the weight of the plates C) Unbalanced forces D) gravitational force

15 C2: Force, Motion and Energy
TEK 8.6A 8.3B 13-54 The diagram shows a boat moving north in a river at 3 m/s while the current in the river moves south at 1 m/s. How will the boat be affected if it enters a part of theriver where the current is moving south at2m/s? A) The boat will move slower. B) The boat will move faster. B) The boat will stop. D) The boat will move to the west.

16 C2: Force, Motion and Energy
TEK 8.6C 8.2E 14-1 A student lets a toy car roll four times down a ramp that is 1 m long. Each time the student covers the surface of the ramp with a different material. The student measures the time it takes the car to roll down the ramp and records the results in the table. Which of these would be the best conclusion based on the data in the table? A) Different surfaces affect how fast a toy car accelerates. B) Different toy cars travel at different speeds. C) Gravity has little effect on the speed of toy cars on different surfaces. D) Air resistance is the greatest factor in limiting the acceleration of different toy cars.

17 C2: Force, Motion and Energy
TEK 6.8A 8.2E 14-4 Four students were asked to classify the activities of the people in the picture as examples of either potential or kinetic energy. Which student correctly classified the activities?

18 C2: Force, Motion and Energy
TEK 6.9C 14-9 When a lion eats a zebra and then uses the energy from the zebra to run, the lion’s body converts — A) chemical energy to mechanical energy B) electrical energy to chemical energy C) chemical energy to light energy D) mechanical energy to chemical energy

19 C2: Force, Motion and Energy
TEK 8.6A 14-17 When a space shuttle was launched, the astronauts onboard experienced an acceleration of 29.0 m/s2. If one of the astronauts had a mass of 60.0 kg, what net force in newtons did the astronaut experience?

20 C2: Force, Motion and Energy
TEK 6.8D 8.2E 14-23 The graph shows distance over time. Which of these situations could be represented by this graph? A) A student walks 1.5 km to a friend’s house in 40 minutes. The two students then walk another 1.5 km to school in 20 minutes. B) A student walks 1.5 km to a friend’s house in 20 minutes. The two students then walk another 1.5 km to school in 40 minutes. C) A student walks 1.5 km to a friend’s house in 30 minutes. The two students then walk another 1.5 km to school in 30 minutes. D) A student walks 1.5 km to a friend’s house in 20 minutes. The two students then walk another 1.5 km to school in 60 minutes.

21 C2: Force, Motion and Energy
TEK 8.6A 14-27 A student uses a magnet to move a kg metal ball. The magnet exerts a force of 5 N, which causes the ball to begin moving. What is the acceleration of the ball when it begins to move? A) 200 m/s2 B)0.125 m/s2 C) 5 m/s2 D) m/s2

22 C2: Force, Motion and Energy
TEK 8.6B 14-34 What is the difference between the velocity and the speed of an object? A) Velocity is the change in distance over time, while speed is the change in velocity over time. B) Velocity has a direction associated with it, while speed has no specific direction. C) Velocity has no direction associated with it, while speed has a specific direction. D) Velocity is the change in speed over time, while speed is the change in distance over time.

23 C2: Force, Motion and Energy
TEK 6.8C 8.2D 14-38 Some students were investigating the speed of a toy car they built. They performed two trials and recorded their data in the table. What was the average speed of the toy car during the two trials to the nearest tenth of a m/s?

24 C2: Force, Motion and Energy
TEK 8.6A 14-41 The diagram below shows a sled moving along a smooth, frictionless track. In which sections of the track will the sled experience an unbalanced force? A) Sections 1 and 3 B) Sections 2 and 3 C) Sections 2 and 4 D) Sections 3 and 4

25 C2: Force, Motion and Energy
TEK 8.6C 8.2E 14-43 The masses of four vehicles and the net forces acting on them as they enter a highway are recorded in the table. Which vehicle has the greatest acceleration as it enters the highway?

26 C2: Force, Motion and Energy
TEK 7.7A 8.2E 14-49 Four students volunteered to help a librarian move containers of library materials. The graph shows the amount of force used to lift the containers. The numbers in the bars show the mass of each container. The results for each student helper are shown in the table. Based on this information, which student helper did not do any work on a container?

27 C2: Force, Motion and Energy
TEK 8.6A 14-54 The diagram shows a homemade car being pushed with a force of 25 N. The force causes the car to move at a constant speed of 3 m/s. What will happen if the force is changed to 35 N? A) The car will move at a constant speed of 13 m/s. B) The speed of the car will not change. C)The speed of the car will increase. D) The speed of the car will decrease to 1 m/s.

28 C2: Force, Motion and Energy
TEK 6.9C 15-3 The main parts of a working clothes dryer are shown in the diagram. This appliance dries clothes primarily by converting — A) electrical energy to heat and mechanical energy B) mechanical energy to heat and electrical energy C) electrical energy to heat and light D) mechanical energy to heat and vaporization

29 C2: Force, Motion and Energy
TEK 7.7A 15-5 An athlete is trying to lift some weights. He successfully lifts 200 N weights, but when he tries to lift 400 N weights, he is unsuccessful. Which of these correctly compares the amount of work the athlete does on the weights? A) The athlete does no work on either the 200 N weights or the 400 N weights. B) The athlete does no work on the 200 N weights but does work on the 400 N weights. C) The athlete does work on both the 200 N weights and the 400 N weights. D) The athlete does work on the 200 N weights but does no work on the 400 N weights.

30 C2: Force, Motion and Energy
TEK 6.8C 15-12 A bus travels 20 km in 30 minutes. What is the average speed of the bus? A) 20 km/h B) 30 km/h C) 40 km/h D) 50 km/h

31 C2: Force, Motion and Energy
TEK 8.6C 8.2E 15-14 During a demonstration of Newton’s laws of motion, a student used the setup shown in Figure 1. The student flicked the index card with a fingertip, and the coin fell straight down into a plastic cup as shown in Figure 2. Which of these best explains why the coin fell straight down into the cup instead of remaining on the index card? A) The coin was at rest until the card was removed, so it tended to remain in the same location. Once the card was gone, the unbalanced force of gravity caused the coin to fall. B) Moving the card applied an action force on the coin. Since the card was gone, gravity applied a reaction force on the coin. C) The card had less mass than the coin, so a smaller force of gravity acted on the card. The larger force of gravity on the coin made it fall. D) The acceleration of the coin falling into the cup was equal and opposite to the acceleration of the card.

32 C2: Force, Motion and Energy
TEK 8.6A 8.2E 15-19 Four students push carts filled with sports equipment across the gym. Each student pushes with the same amount of force. Which cart has the greatest change in speed?

33 C2: Force, Motion and Energy
TEK 6.8A 8.3B 15-25 A student drew the diagram below to show the movement of water through a hydroelectric dam. The student used the diagram to describe changes in the potential and kinetic energy of the water. At which location is the gravitational potential energy of the water the greatest?

34 C2: Force, Motion and Energy
TEK 8.6A 8.2E 15-30 A basketball with a mass of 0.60 kg is accelerated with a force of N. If resisting forces are ignored, what is the acceleration of the basketball to the nearest m/s2?

35 C2: Force, Motion and Energy
TEK 8.6C 8.3A 15-35 The diagram below shows two different forces acting on a cyclist riding a bicycle. The total mass of the cyclist and the bicycle is kg. Based on this information, what is the acceleration of the cyclist? A) 0.66m/s2 backward, because the force of the air slows the cyclist down B) 0.66m/s2 forward, because the applied force is greater than the force of the air C) 2.3m/s2 backward, because the forces are opposite and not equal D) 2.3m/s2 forward, because the cyclist’s inertia is greater than the force of the air

36 C2: Force, Motion and Energy
TEK 8.6B 15-37 37Which of the following best describes the velocity of an object? A) 30 m/s B) 30 m east C) 30 m/s east D) 30m/s2

37 C2: Force, Motion and Energy
TEK 8.6C 15-43 A student jumps off a sled toward the west after it stops at the bottom of an icy hill. Based on the law of action–reaction, in what direction will the sled most likely move as the student jumps off?

38 C2: Force, Motion and Energy
TEK 8.6A 8.2A 15-49 A student used a video camera to record another student dropping a marble through water in a graduated cylinder. The students watched the video in slow motion and made the observations shown. During which part or parts of the marble’s fall did the marble experience unbalanced forces? A) Part 1 only B) Parts 1 and 2 only C) Part 3 only D) Parts 2 and 3 only

39 C2: Force, Motion and Energy
TEK 6.8D 8.2D 15-52 A student runs two times around a running path at a local park. Each lap is 3 km. The student completes the first lap in 20 minutes. The student then sits on a bench and rests for 5 minutes before completing the second lap in 25 minutes. Which graph best represents the student’s motion?


Download ppt "C2: Force, Motion and Energy"

Similar presentations


Ads by Google