1. Programmable Logic Controllers
LO1: Understand the design and operational characteristics of a PLC system

2. Learning Outcome 1
LO1: Understand the design and operational characteristics of a PLC system
1.3 evaluate the different types of communication link used in programmable logic control systems

3. Behavioural Objectives
At the end of this session the students will be able to cables that meet…
selection criteria, description of features, frequency ranges, technology eg analogue, digital, wireless; cable eg twisted pairs, coaxial, fibre-optic, shielded/unshielded, categories, operational lengths; connector eg Bayonet-Neill-Concelman (BNC), registered jack (RJ-45), straight tip (ST), universal serial bus (USB) type A and type B; opto-isolator eg photodiode, phototransistor, thyristors, triacs

4. Remote Connections
When there are many inputs and outputs located considerable distances away from the PLC, though it would be possible to run cables from each such device to the PLC, a more economic solution is to use input / output modules in the vicinity of the inputs and outputs and use just a single core cable to connect each over the long distances to the PLC instead of using the multicore cable that would be needed without such I/O modules

5. Remote Connections PLC Input and Output connections
Twisted-pair or screened cable, or fibre-optic cable, communications link
PLC
Input and Output connections
Power cable
Remote input / output module

6. PLC Networks
In some situations a number of PLCs may be linked together via a master PLC unit sending and receiving input / output data from other units
Master PLC
Communications Module
Other I/O Modules
PLC
PLC
Communications Port

7. PLC Networks
The distant PLCs do not contain the control programme since all the control processing is carried out by the master PLC

8. Cables
The cables used for communicating data between remote input/output modules and a central PLC or remote PLC and the master PLC are typically twisted-pair cabling, often routed through grounded steel conduit to reduce electrical ‘noise’.

9. Twisted Pair
Unshielded Twisted Pair (UTP) cabling is a type of wiring in which two conductors of a single circuit are twisted together for the purposes of cancelling out electromagnetic interference from external sources

10. Twisted Pair
Twisted pair cabling is often used in data networks for short and medium length connections because of its relatively lower costs compared to optical fibre and coaxial cable.

11. Twisted Pair Shielded twisted pair (STP or STP-A)
Screened twisted pair (ScTP or F/TP) 
Screened shielded twisted pair (S/STP or S/FTP) 

12. Twisted Pair
Twisted pair cables are often shielded in an attempt to prevent electromagnetic interference. Because the shielding is made of metal, it may also serve as a ground. However, usually a shielded or a screened twisted pair cable has a special grounding wire added called a drain wire.
This shielding can be applied to individual pairs, or to the collection of pairs. When shielding is applied to the collection of pairs, this is referred to as screening.

13. Twisted Pair
Shielding provides an electric conductive barrier to attenuate electromagnetic waves external to the shield and provides conduction path by which induced currents can be circulated and returned to the source, via ground reference connection.

14. Skin-depth
As the frequency of the communicated signal increases then less and less of the cross-sectional area of the cable is used to transmit electricity.
At a particular frequency only the surface of the conductor actually conducts electricity. Above this frequency the cable will not conduct, rather it will radiate.

15. Coaxial Cables
Co-axial cable enables higher data rates to be transmitted and does not require the shielding of steel conduit

16. Coaxial Cables
Coaxial cable is used as a transmission line for radio frequency signals.
Its applications include feed-lines connecting radio transmitters and receivers with their antennas, computer network (internet) connections and distributing cable television.
Coaxial cable also provides protection of the signal from external electromagnetic interference.

17. Fibre Optic Cables
Fibre-optic cabling has the advantage of resistance to noise, small size and flexibility and is now becoming now widely used

18. BNC Connectors
The BNC connector (Bayonet Neill-Concelman (BNC) is a miniature quick connect / disconnect RF connector used for coaxial cable
It features two bayonet lugs on the female connector which mates with a quarter turn of the coupling nut to the male connector

19. BNC Connectors
BNC connectors normally work with frequencies up to 2 GHz and voltages up to 500 v
BNC connectors can be used on Ethernet networks both on cable interconnections and network cards

20. Registered Jack (RJ-45)
A Registered Jack (RJ) is a standarised physical network interface – standardising both both jack construction and wiring pattern – for connecting telecommunications or data equipment to a service provided by local exchange carrier or long distance carrier.
The physical connectors that Registered Jacks use are mainly of the modular connector and 50-pin miniature ribbon connector types. For example, RJ11 uses a 6P2C (6-position, 2-conductor) modular plug and jack.

21. Registered Jack (RJ-45)

22. Registered Jack (RJ-45)
Strictly, Registered Jack refers to both the female physical connector (modular connector) and its wiring, but the term is often used loosely to refer to modular connectors regardless of wiring or gender, such as in Ethernet over twisted.

23. Straight Tip (ST) Connectors
An optical fiber connector terminates the end of an optical fibre and enables quicker connection and disconnection than splicing.
The connectors mechanically couple and align the cores of fibres so light can pass. Better connectors lose very little light due to reflection or misalignment of fibres.
In all about 100 fibre optic connectors have been introduced to the market.

24. Straight tip (ST) Connectors

25. Universal Serial Bus (USB)
Universal Serial Bus (USB) is an industry standard developed in mid-1990 that defines the cables, connectors and communications protocols used in a bus for connection, communication and power supply between computers and electronic devices

26. Universal Serial Bus (USB) type A and B

27. Universal Serial Bus (USB)