Presentation is loading. Please wait.

Presentation is loading. Please wait.

1 Fulvio TESSAROTTO CERN, 20/03/2008 - GDD Meeting - Contribution from Trieste FIRST LOOK AT THGEM IN TRIESTE LAB. The set-up to measure currents THGEM.

Published byClarence Flowers Modified over 8 years ago

Similar presentations

Presentation on theme: "1 Fulvio TESSAROTTO CERN, 20/03/2008 - GDD Meeting - Contribution from Trieste FIRST LOOK AT THGEM IN TRIESTE LAB. The set-up to measure currents THGEM."— Presentation transcript:

1 1 Fulvio TESSAROTTO CERN, 20/03/2008 - GDD Meeting - Contribution from Trieste FIRST LOOK AT THGEM IN TRIESTE LAB. The set-up to measure currents THGEM prototypes from ELTOS First measurements on 4 pieces Chamber for prototype test The set-up to measure signals Fulvio Tessarotto

2 2 Fulvio TESSAROTTO CERN, 20/03/2008 - GDD Meeting - Contribution from Trieste The power supply We used for this measurement one channel of the CAEN N471A power supply, reading the voltage from the LED display ( +- 1 V ) and the current from the “current monitor” output (5 mV offset, 1 mV/nA) We checked the stability of the power supply by looking at signals on the HV output, using a HV cable, a 1 nF capacitor and Le Croy oscilloscope Typical ripple has ~ 30 μs period, 80 mV pp at HV=4kV, the ripple amplitude being roughly linear with voltage

3 3 Fulvio TESSAROTTO CERN, 20/03/2008 - GDD Meeting - Contribution from Trieste Ripple on the oscilloscope

4 4 Fulvio TESSAROTTO CERN, 20/03/2008 - GDD Meeting - Contribution from Trieste HV – Power Supply: Ripples HV= 2kV HV= 4kV Power Supply HV cable 1nF ?? LEMOcable SCOPE

5 5 Fulvio TESSAROTTO CERN, 20/03/2008 - GDD Meeting - Contribution from Trieste HV – Power Supply: Ripples Receiving a phone call

6 6 Fulvio TESSAROTTO CERN, 20/03/2008 - GDD Meeting - Contribution from Trieste Home-made picoamperometer Implemented scheme CMOS Operational Amplifier: AD 8607 10 MΩ feedback resistor: VISHAY CNS020 (+- 0.02%, +- 10 ppm/ºC) 1 nF to 100 nF feedback capacitor 10 M protection resistor

7 7 Fulvio TESSAROTTO CERN, 20/03/2008 - GDD Meeting - Contribution from Trieste The home-made picoammeters Several temporary arrangements were tested for the home- made picoamperometers, using solderless breadboard, micro pcb on ceramic insulators and customly designed pcb’s for home-made picomaperometers - When powered by batteries they work fine at HV (tested up to 8kV), with stable offsets <10 pA - Using a battery + resistor current source of ~60 pA we checked that the reading was correct at few pA level; the ultimate resolution is still to be determined At ground, the agreement between Keithley measurements and home-made picoammeters values is roughly 1pA

8 8 Fulvio TESSAROTTO CERN, 20/03/2008 - GDD Meeting - Contribution from Trieste CMOS Operational Amplifier: AD 8607

9 9 Fulvio TESSAROTTO CERN, 20/03/2008 - GDD Meeting - Contribution from Trieste What we observed Power Supply Box with ThickGEM – no holes

10 10 Fulvio TESSAROTTO CERN, 20/03/2008 - GDD Meeting - Contribution from Trieste First tests of the set-up 1) PS – cable1 – PA – cable2 Oscillations with amplitudes proportional to L x V (cable length x PS voltage; no oscillations with PS off). 2) PS – cable1 – PA1 – cable2 – THGEM – cable3 – PA2 Oscillations are the same on PA1 and PA2 Decision: redundancy, shortest possible cables, design final set-up but start measurements before it is ready

11 11 Fulvio TESSAROTTO CERN, 20/03/2008 - GDD Meeting - Contribution from Trieste

12 12 Fulvio TESSAROTTO CERN, 20/03/2008 - GDD Meeting - Contribution from Trieste

13 13 Fulvio TESSAROTTO CERN, 20/03/2008 - GDD Meeting - Contribution from Trieste

14 14 Fulvio TESSAROTTO CERN, 20/03/2008 - GDD Meeting - Contribution from Trieste Reading the voltmeters We decided to register picoammeter redings by saving pictures of the displays CANON Camera programmed to shoot every 2 seconds: this allows registering measurements and all intermediate operations done by humans From picture analysis the images on LED displays are translated into numbers (~ 40000 pictures so far) This solution avoids electrical connections to the acquisition system

15 15 Fulvio TESSAROTTO CERN, 20/03/2008 - GDD Meeting - Contribution from Trieste

16 16 Fulvio TESSAROTTO CERN, 20/03/2008 - GDD Meeting - Contribution from Trieste We are building a more compact set-up Box for 4 THINGS - HV connectors will be on the back side PCB OEM44 voltmeter Connectors for batteries Resistor (10Mohm) Capacitor (10nF) OA - AD8607 Guarding “ring” Connectors for OEM44 voltmeter

17 17 Fulvio TESSAROTTO CERN, 20/03/2008 - GDD Meeting - Contribution from Trieste THGEM prototype geometry Size of active area: 30mm x 30 mm Thickness: 0.4 mm Holes diameter: 0.4 mm Pitch: 0.8 mm diameters Material: R-1566 Panasonic (halogen free, anti CAF) Cu thickness: 35 μm

18 18 Fulvio TESSAROTTO CERN, 20/03/2008 - GDD Meeting - Contribution from Trieste Summary table Nam eDrilling 0.4 mmRim 1 (μm)Rim 2 (μm)rim productionmaterial M1Y00NOPanasonic M2Y250DrillingPanasonic M3Y500DrillingPanasonic M4Y1000DrillingPanasonic M5Y50 Two Sides DrillingPanasonic RNO Panasonic RINO Isola C1Y10 EtchingPanasonic C2Y25 EtchingPanasonic C3Y50 EtchingPanasonic C3IY50 EtchingIsola C4Y100 EtchingPanasonic C5Y10 Laser + EtchingPanasonic C6Y50 Laser + EtchingPanasonic C7Y10 Global EtchingPanasonic We received 10 samples per type

19 19 Fulvio TESSAROTTO CERN, 20/03/2008 - GDD Meeting - Contribution from Trieste Documentation example C3

20 20 Fulvio TESSAROTTO CERN, 20/03/2008 - GDD Meeting - Contribution from Trieste The FR4 material

21 21 Fulvio TESSAROTTO CERN, 20/03/2008 - GDD Meeting - Contribution from Trieste

22 22 Fulvio TESSAROTTO CERN, 20/03/2008 - GDD Meeting - Contribution from Trieste

23 23 Fulvio TESSAROTTO CERN, 20/03/2008 - GDD Meeting - Contribution from Trieste

24 24 Fulvio TESSAROTTO CERN, 20/03/2008 - GDD Meeting - Contribution from Trieste

25 25 Fulvio TESSAROTTO CERN, 20/03/2008 - GDD Meeting - Contribution from Trieste Procedure THGEM prototypes are kept under vacuum before and after measurement Handling is done with polyethylene gloves only Mounting at the centre of the test box, soldering cables and screwing nylon screws on ~5 cm nylon columns: ~ 10 min HV provided to “TOP” of THGEM prototype, “BOTTOM” at ground (some field above while no field below THGEM) One day flushing with N2 at ~20 l/h before switching HV on

26 26 Fulvio TESSAROTTO CERN, 20/03/2008 - GDD Meeting - Contribution from Trieste Results from the first THGEMS

27 27 Fulvio TESSAROTTO CERN, 20/03/2008 - GDD Meeting - Contribution from Trieste

28 28 Fulvio TESSAROTTO CERN, 20/03/2008 - GDD Meeting - Contribution from Trieste

29 29 Fulvio TESSAROTTO CERN, 20/03/2008 - GDD Meeting - Contribution from Trieste

30 30 Fulvio TESSAROTTO CERN, 20/03/2008 - GDD Meeting - Contribution from Trieste

31 31 Fulvio TESSAROTTO CERN, 20/03/2008 - GDD Meeting - Contribution from Trieste

32 32 Fulvio TESSAROTTO CERN, 20/03/2008 - GDD Meeting - Contribution from Trieste

33 33 Fulvio TESSAROTTO CERN, 20/03/2008 - GDD Meeting - Contribution from Trieste Maximum voltage reached defing V max as the highest value of HV which has been applied for more than 1 min without discharges we would obtain: Sample Vmax M1 2200 M5 2575 C3 2100 E1 2550

34 34 Fulvio TESSAROTTO CERN, 20/03/2008 - GDD Meeting - Contribution from Trieste THGEM test chamber

35 35 Fulvio TESSAROTTO CERN, 20/03/2008 - GDD Meeting - Contribution from Trieste

36 36 Fulvio TESSAROTTO CERN, 20/03/2008 - GDD Meeting - Contribution from Trieste Test of analog r/o chain  Single photon signals are generated by a picosecond laser providing ~20 ps long pulses and a correlated timing signal  Laser amplitudes are reduced by geometric selection and laser tune down to a probability of 95% no photon pulses.  One pixel of a Hamamtsu R7600-03-M16 MAPMT is used to provide signal to our analog r/o chain through a resistive divider (reducing the signal by a factor 4).  The ORTEC 142 preamp coupled to the ORTEC 450 amplifier and the CAEN N957 was used to collect amplitude spectra  a rough calibration was performed for several gain factors, showing evidence of non linearities for large signals: only signals in the linear range have been used  Spectra were taken at various gains and combined in a single plot to increase the dynamic range of the measurement

37 37 Fulvio TESSAROTTO CERN, 20/03/2008 - GDD Meeting - Contribution from Trieste Single photon amplitude spectra from MAPMT

Download ppt "1 Fulvio TESSAROTTO CERN, 20/03/2008 - GDD Meeting - Contribution from Trieste FIRST LOOK AT THGEM IN TRIESTE LAB. The set-up to measure currents THGEM."

Similar presentations

Status of test beam data analysis … with emphasis on resistive coating studies Progress and questions 1Meeting at CEA Saclay, 25 Jan 2010Jörg Wotschack,

Status of test beam data analysis … with emphasis on resistive coating studies Progress and questions 1Meeting at CEA Saclay, 25 Jan 2010Jörg Wotschack,
1 First observations on CsI -coated ThGEM in Trieste presented by Gabriele Giacomini phone meeting 06/08/2008.

1 First observations on CsI -coated ThGEM in Trieste presented by Gabriele Giacomini phone meeting 06/08/2008.
Micro MEsh GASeous Detectors (MicroMegas)

Micro MEsh GASeous Detectors (MicroMegas)
Mechanical check of PMT Check base: Remove black tape and two small screws that secure the base. Tighten the nuts on the BNC connector for the HT input.

Mechanical check of PMT Check base: Remove black tape and two small screws that secure the base. Tighten the nuts on the BNC connector for the HT input.
A.Kashchuk Muon meeting, CERN 22-23.04.2002 Presented by A.Kashchuk.

A.Kashchuk Muon meeting, CERN Presented by A.Kashchuk.
Tests of a 10cm by 10cm triple GEM detector 2015-06-08.

Tests of a 10cm by 10cm triple GEM detector
Large Cell Scope Pictures, Part II HV Gnd 1nF Large Cell Tube Anode signal Phi Cathode signal scope S1 S2 S1 S2 This is a follow-up on Richard’s measurement.

Large Cell Scope Pictures, Part II HV Gnd 1nF Large Cell Tube Anode signal Phi Cathode signal scope S1 S2 S1 S2 This is a follow-up on Richard’s measurement.
ECAL electronics Guido Haefeli, Lausanne PEBS meeting 10.Jan. 2011 1.

ECAL electronics Guido Haefeli, Lausanne PEBS meeting 10.Jan
1 New dividers for LAV photomultipliers G.Corradi,D.Tagnani,C.Paglia, M. Raggi LAV working group CERN 3/2/2010.

1 New dividers for LAV photomultipliers G.Corradi,D.Tagnani,C.Paglia, M. Raggi LAV working group CERN 3/2/2010.
1 Production issues of THGEMS at ELTOS The production procedure Quality checks - visual inspection - electrical tests Problems we faced Conclusions Fulvio.

1 Production issues of THGEMS at ELTOS The production procedure Quality checks - visual inspection - electrical tests Problems we faced Conclusions Fulvio.
Yu. Guz 18/12/20061 HCAL commissioning: status and plans Yu. Guz, IHEP, Protvino Outline 1. current status of HCAL a)CW+PM b)signal cables c)LED monitoring.

Yu. Guz 18/12/20061 HCAL commissioning: status and plans Yu. Guz, IHEP, Protvino Outline 1. current status of HCAL a)CW+PM b)signal cables c)LED monitoring.
Experiment 12 Non-Inverting Amplifier. Experimental Procedure Clarification in Step 3 (Modeling) – To perform the DC Sweep in the sinusoidal voltage source.

Experiment 12 Non-Inverting Amplifier. Experimental Procedure Clarification in Step 3 (Modeling) – To perform the DC Sweep in the sinusoidal voltage source.
Rate and Gain Measurements of the 1-m long GEM detector Aiwu Zhang 2015-07-06 EIC tracking R&D weekly meeting.

Rate and Gain Measurements of the 1-m long GEM detector Aiwu Zhang EIC tracking R&D weekly meeting.
CERN DC Spark System Capabilities Anders Korsbäck, BE-RF-LRF University of Helsinki.

CERN DC Spark System Capabilities Anders Korsbäck, BE-RF-LRF University of Helsinki.
Noise studies: hardware tests and preliminary results Anna, Anton, Giovanni, Pigi, Silvia, A. Boiano, A. Vanzanella.

Noise studies: hardware tests and preliminary results Anna, Anton, Giovanni, Pigi, Silvia, A. Boiano, A. Vanzanella.
1 Fulvio TESSAROTTO RD51 meeting, Paris, 14/10/2008 THGEM production at ELTOS Production of THGEM at ELTOS S.p.A. Company profile Production procedures.

1 Fulvio TESSAROTTO RD51 meeting, Paris, 14/10/2008 THGEM production at ELTOS Production of THGEM at ELTOS S.p.A. Company profile Production procedures.
Dimensions of the PDM frame: 167mm x 167mm x 28.7mm.

Dimensions of the PDM frame: 167mm x 167mm x 28.7mm.
New Developments in Large Area THGEMs & APV Exercise INFN – Sezione di Trieste Carlos Alexandre Fernandes dos Santos 11/December/2014.

New Developments in Large Area THGEMs & APV Exercise INFN – Sezione di Trieste Carlos Alexandre Fernandes dos Santos 11/December/2014.
CAEN November 15, 2002 Vandelli W. 1 Test Conditions Prototype fed by CAEN Module 2527 through 100 m long cables From channels status page on generator.

CAEN November 15, 2002 Vandelli W. 1 Test Conditions Prototype fed by CAEN Module 2527 through 100 m long cables From channels status page on generator.
EC front unit status. Outline Conclusions from mechanical prototype and actions taken Status of electrical prototype KIT’s work for TA Dev plan (tests)

EC front unit status. Outline Conclusions from mechanical prototype and actions taken Status of electrical prototype KIT’s work for TA Dev plan (tests)

Similar presentations

Ads by Google