1. Link Aggregation V1.1

2. Objectives Understand the features and benefits of link aggregation Grasp the basic link aggregation configuration steps of G series

3. Agenda Features and benefits of link aggregation G series link aggregation configuration

4. What is Link aggregation? Link aggregation introduces a bandwidth aggregation capability Link aggregation inter-operates seamlessly with network platforms from other vendors such as the Cisco Catalyst 5000 and server vendors such as SUN Microsystems and Auspex. Link aggregation is the ability to aggregate 10/100 or Gigabit Ethernet links between devices and operate the group of links as a single high capacity link.

5. Port trunking Fast Ethernet 4 Fast Ethernet 3 Fast Ethernet 2 Fast Ethernet 1 D E F A B C Port trunking Port Trunking

6. Benefits Bandwidth is increased by grouping links together. If link D becomes broken, then all the traffic will be redistributed between links A, B, and C automatically. ABCDABCD

7. Load Balancing (per flow) Flows are assigned to a particular link by the load balancing algorithm. The Flow uses the same link throughout its duration. Round-robin (Default setting) Link Utilization Flow 1A Flow 2B Flow 3C Flow 4D

8. D E F D D FE 1 FE 2 FE 3 FE … A->D B->D C->D etc. Flow Output Path FE 4 FE 3 FE 1 FE … D->A D->B D->C etc. Flow Output Path D D D D D D A B C D Fast Ethernet 4 Fast Ethernet 3 Fast Ethernet 2 Fast Ethernet 1 Port trunking Load Balance Port trunking uses load distribution to share the links

9. Agenda Features and benefits of link aggregation G series link aggregation configuration

10. Configuration of G Series The G series equipment supports up to 32 TRUNK groups; one TRUNK group contains 8 ports at most. The G series equipment supports the aggregation of ports from different slots, but all ports should be under the same duplex mode and have the same speed. The G series equipment supports three modes of ports:access, trunk or hybrid ， but all ports in one group should be same.

11. Three preconditions of link aggregation Support link aggregation across interface cards, member port can be at any interface card, but the member port must work at full-duplex mode and the working rate must be the same for all the member ports. Mode of the member ports should be the same, the mode can be access 、 trunk or hybrid.

12. Link aggregation methods Static trunk Static Trunk add physical ports to the Trunk group to form a logical port. This way is not good for observing the status of the aggregated port. LACP (Link aggregation Control Protocol) 1. Comply with IEEE 802.3ad standard. 2. LACP work by protocols to aggregate multiple physical ports to a trunk group, thus forming a logical port dynamically. LACP will automatically aggregate together to get the maximum bandwidth.

13. Configuration of G Series 1.Create Trunk Group ZXR10(config)#interface 2.Bundling port to trunk group, setting port aggregation mode smartgroup mode {passive|active|on} When the aggregation mode is set to be On, the port runs static trunk, two ends participating in aggregation should be set to be On mode. When aggregation mode is active or passive, the port runs LACP. Active means the port is in active negotiation mode; passive means the port is in passive negotiation mode. When configuring dynamic link aggregation, set the aggregation mode of one end port to be active and the other end to be passive, or active both.

14. Configuration of G Series 3. Setting load balance mode smartgroup load-balance ZXR10 T160G/T64G port link aggregation supports 6 types of load balance modes which respectively based on : dst-ip Dst ip address dst-mac Dst mac address src-dst-ip Src-dst ip address src-dst-mac Src-dst mac address src-ip Src ip address src-mac Src mac adddress

15. Configuration of G Series Display the aggregation status of member port: ZXR10(config)#show lacp 2 internal Smartgroup:2 Actor Agg LACPDUs Port Oper Port RX Mux Port State Interval Priority Key State Machine Machine ------------------------------------------------------------------ fei_3/17 selected 30 32768 0x202 0x3d current collecting-distributing fei_3/18 selected 30 32768 0x202 0x3d current collecting-distributing

16. Instance of configuration smartgroup1 ZTE1 ZTE2 ZTE1(config)# interface smartgroup1 ZTE1(config-if)# exit ZTE1(config)# interface fei_2/1 ZTE1(config-if)# smartgroup 1 mode on ZTE1(config-if)# exit ZTE1(config)# interface fei_2/2 ZTE1(config-if)# smartgroup 1 mode on ZTE1(config-if)# exit ZTE1(config)# interface smartgroup1 ZTE1(config-if)# switchport mode trunk ZTE1(config-if)# switchport trunk vlan 10

17. Summarization Link aggregation is used for load balancing Link aggregation can be used in multi-vendor products environment The aggregation ports should be under the same duplex mode and have the same speed.

18. Questions When to use the link aggregation? What’s the main feature of link aggregation? What parameters should be matched in order to add ports to a trunk group?