Presentation is loading. Please wait.

Presentation is loading. Please wait.

Scanning capacitance microscopy

Similar presentations


Presentation on theme: "Scanning capacitance microscopy"— Presentation transcript:

1 Scanning capacitance microscopy
Scanning capacitance technique actually measures the dC/dV signal which is inversely proportional to doping. The advantages of this technique include a large measurement range (1015 – 1020 cm-3), and resolution of <10 nm For capacitance measurement a low frequency ac voltage is applied to the sample. The ac voltage periodically changes the tip-sample capacitance. The sensor produces a high frequency signal to measure very small capacitance changes. Goutam Koley

2 Application of capacitance microscopy
Cross-sectional measurement in a MOSFET under actual operation Goutam Koley

3 Applications to GaN samples
Morphology image Capacitance image C-V curve The dC/dV decreases around the dislocations indicating the reduction in the background carrier concentration Goutam Koley

4 Problems 2 Calculate the amplitude of the 17 KHz force acting on the cantilever for an applied ac voltage of 10 V rms (frequency 17 KHz). The cantilever dimensions are 30 and 100 microns respectivley. It is 2 microns away from the ground. The work function of the cantilever is 5.65 eV, and that of the sample is 5.15 eV. Assuming that this force is applied at the edge of the cantilever, what is the deflection if the spring constant is 0.1 N/m.

5 SEM Microcharacterization
SEM characterization modes: Microscopy Electron Beam Induced Current Cathodoluminescence Energy dispersive X-Ray Spectrum Analysis Electron beam lithography

6 Fundamental Physics I Trivia: SEM working principles were outlined in 1942 by Zworykin, but it was not until 10 years later that a working machine was assembled in Cambridge University. The SEM operates with electrons having energy 20 – 30 keV. For 20 KeV, the De Broglie wavelength e = nm. The interaction of the electrons with a given material produces secondary electrons, backscattered electrons, characteristic and continuum X-Rays, Auger electrons, photons, and electron-hole pairs

7 Fundamental Physics II and Applications
Re can be found out from the empirical expression Where  is the sample density, and E is the energy in keV The interaction of the electrons with a given material produces secondary electrons, backscattered electrons, characteristic and continuum X-Rays, Auger electrons, photons, and electron-hole pairs

8 SEM imaging parameters
Magnification M = (length of CRT display) / (length of sample area scanned). In modern machines magnifications up to 200, 000 can be achieved. Resolution as low as 1 nm can be achieved, which is usually limited not by the wavelength of the electrons but by the diameter of the focused electron beam and electron scattering in the sample from the valence and the core electrons. Due to electron scattering the original collimated beam gets broadened. Contrast of the SEM depends mostly on the sample topography since most of the secondary electrons are emitted from the top 10 nm of the sample. The contrast C depends on angle as: C = tan d, where  is the angle from normal incidence. At 45° angle, d = 1° causes change in contrast by 1.75%. The contrast in backscattered electrons can come from the difference in atomic number Z. The SEM operates in a very different manner from optical microscope, in that electrons even away from the detector are attracted, amplified, and displayed on the CRT. Thus the image displayed in the CRT is not a true image of the sample.

9 SEM working parts I Trivia: SEM was discovered in 1942 by V. K. Zworykin, but it was not until 10 years later that a fully functional microscope was developed by researchers at Cambridge University The basic SEM consist of an Electron gun, and a few focusing lenses, and detector. For EDS an X-Ray detector is also used The pressure inside the chamber is maintained at ~10-8 Torr vacuum. Microscopes are usually operated in the voltage range of 20 – 30 keV, but for insulating samples 1 kV or less can be used. For insulating samples a thin metal coating can also be used. The standard electron detector is an Everhart-Thornley design that is capable of amplifying electron currents by almost a million times.

10 SEM working parts II: Electron sources
There are mainly three types of electron sources Tungsten hairpin filament: This is simply a tip that is heated to an extremely high temperature of ~2500 C to make electrons have high enough energy to overcome the surface work function of ~4.5 eV To get higher electron current stable materials with lower work function is preferred. LaB6 as polycrystalline powder is used to reduce the work function to about half that of the tungsten metal and significantly increasing the current In field-emission guns, an extremely high electric field is applied to have the electrons “tunnel” through the barrier into vacuum. These could be operated as “cold” or they could be operated at higher temperature, when they are called Schottky emitters. The later ones are easier to clean and maintain


Download ppt "Scanning capacitance microscopy"

Similar presentations


Ads by Google