1. IEEE802.11a 指導教授 : 高永安 學生 : 陳穎俊

3. PLCP preamble

4. PLCP data modulation and modulation rate change PLCP preamble 作傳輸時是 採用 OFDM modulated fixed waveform The IEEE802.11SIGNAL field,BPSK-OFDM modulated at 6 Mbit/s,shall indicate the modulation and coding rate that shall be used to transmit the MPDU The transmitter(receiver)shall initiate the modulation (demodulation) constellation and the coding rate according to the RATE indicated in the SIGNAL field. The MPDU transmission rate shall be set by the DATARATE parameter in the TXVECTOR

5. PMD operating specifications (general) Outline description Operating frequency range Channelization TX RF delay Slot time Transmit and receive antenna port impedance Transmit and receive operating temperature range

6. Block diagram of the transmitter and receiver for the OFDM PHY

8. Operating frequency range The OFDM PHY shall operate in the 5GHz band,as allocated by a regulatory body in its operational region. Spectrum allocation in the 5 GHz band is subject to authorities responsible for geographic-specific regulatory domains(e.g.,global,regional,and national).

9. Channelization The set of valid operating channel numbers by regulatory domain

10. channelization

11. Channelization

12. TX RF delay Slot time The TX RF delay time shall be defined as the time between the issuance of a PMD.DATA.request to the PMD and the start of the corresponding symbol at the air interface The slot time for the OFDM PHY shall be 9us, which is the sum of the RX-to-TX turnaround time, MAC processing delay,and CCAdetect time(<4us) The propagation delay shall be regarded as being included in the CCA detect time

13. Transmit and receive antenna port impedance Transmit and receive operating temperature range The transmit and receiver antenna port(s) impedance shall be 50 maga if the port is exposed. Type 1 defined as 0 度 C 到 40 度 C Type 1 defined as -20 度 C 到 50 度 C Type 1 defined as -30 度 C 到 70 度 C

14. PMD transmit specificatons Transmit power levels Transmit spectrum mask Transmit spurious Transmit center frequency tolerance Modulation accuracy Transmit modulation accuracy test

15. Transmit power levels The maximun allowable output power according to FCC regulation

16. Transmit specturm mask

17. Transmission spurious Transmit center and Symbol clock frequency tolerance Spurious transmissions from compliant devices shall conform to national regulations The transmission center (symbol clock) frequency tolerance shall be 20% ppm maximun. The transmission center and the symbol clock frequency shall be derived from the same reference.

18. Modulation accuracy Transmitter spectral flatness The average energy of the constellations in each of the spectral lines – 16..-1 and +1..+16 will deviate no more than +- 2dB from their average energy. Transmitter constellation error The relative constellation RMS error,average over subcarriers, OFDM frames, and pacjets, shall not exeed a data-rate depend- ent value

19. Transmitter constellation error

21. PMD receiver specificatons Receiver minimum input level sensitivity Adjacent channel rejection Non-adjacent channel rejection Receiver maximun input level CCA sensitivity

22. Receviver minimum input level sensitivity The packet error rate shall be less than 10% at a PSDU length of 1000 bytes for rate-dependent input levels shall be the numbers listed in Table 91 or less The minimum input levels are measured at the antenna connector(NF of 10 dB and 5 dB implementation margi- ns are assumed)

24. Adjacent (Non-adjacent)channel rejection The adjacent (non- adjacent) channel rejection shall be measured by setting the desires signal ’ s strength 3 dB above the rate-dependent sensitivity specified in Table 91 and raising the power of the interfering signal until 10% PER is caused for a PSDU length of 1000 bytes. The power difference between the interfering and the desired channel is the corresponding adjacent (non- adjacent) channel rejection.

25. Receiver maximun input level The receiver shall provide a maximum PER(packet error rate) of 10% at a PSDU length of 1000 bytes, for a maximum input level of – 30dB measured at the antenna for any baseband modulation