2. Overview What is Arduino? What is it used for? How to get started Demonstration Questions are welcome at any time.

3. What is Arduino? “Arduino is an open-source physical computing platform based on a simple i/o board and a development environment that implements the Processing / Wiring language. Arduino can be used to develop stand-alone interactive objects or can be connected to software on your computer.“ ( www.arduino.cc, 2006 )

4. Arduino is a platform A physical Input / Output board (I/O) with a programmable Integrated Circuit (IC).

5. Arduino is a platform Also including an Integrated Development Environment (IDE) for programming. The language itself is based in C but is largely modeled upon the www.processing.org language.

6. What is it used for? Physical Computing projects / research Interactive Installations Rapid prototyping When you wish to move beyond the traditional Mouse, Keyboard and Monitor to develop novel and custom interactions in your project work.

7. What can it do? Sensors ( to sense stuff ) –Push buttons, touch pads, tilt switches. –Variable resistors (eg. volume knob / sliders) –Photoresistors (sensing light levels) –Thermistors (temperature) –Ultrasound (proximity range finder) Actuators ( to do stuff ) –Lights, LED’s –Motors –Speakers –Displays (LCD)

8. Why Arduino? It is Open Source, both in terms of Hardware and Software. It is cheap, the hardware can be built from components or a prefab board can be purchased for approx $35 AUD It can communicate with a computer via serial connection over USB (Bluetooth model coming soon!). It can be powered from USB or standalone DC power.

9. Why Arduino? It can run standalone from a computer (chip is programmable) and it has memory (a small amount). It can work with both Digital and Analogue electronic signals. Sensors and Actuators. You can make cool stuff! Some people are even making simple robots, and we all know robots are just cool.

11. Not so fast! It’s important to note at this stage that Arduino’s are electronic devices. This means you MUST consider electrical safety and understand the basics before diving straight in. The board itself doesn’t operate at what would normally be considered dangerous Voltages or Amperage, but if in doubt at any stage of use you should seek more expert advice.

12. Getting up and running The power mode must be selected before you plug the board into anything. When powering from the USB cable (5 volts) the jumper should be closest to the USB input, for DC supply the jumper should be closest to the DC input.

13. Getting up and running Plug it into the USB port and install the USB drivers that come with the IDE. Open up the Arduino IDE and select the COM port, usually COM1 or COM2 on a Windows machine. Within the IDE, select the BAUD rate (communication speed for serial connections) Set BAUD rate to 19200 on Windows, 9600 for Mac?

14. Digital Sensors vs Analogue Digital Use fixed HIGH and LOW signals to transmit data. Binary system, High =1, Low = 0. Reads input based on stream of Highs and Lows. Analogue Uses infinitely variable streams of signals.

15. Digital sensors\signals Blue = Analogue Red = Digital

16. Digital, Analogue, PWM All in all it can be summarized in the following fashion. DIGITAL IS “On and Off” ANALOGUE IS “How MUCH on or off” PWM IS “How OFTEN on or off”

17. Digital’s Hot Sister, PWM Pulse Width Modulation, or PWM, is a technique for getting analog results with digital means. Digital control is used to create a square wave, a signal switched between on and off. This on-off pattern can simulate voltages in between full on (5 Volts) and off (0 Volts) by changing the portion of the time the signal spends on versus the time that the signal spends off. The duration of "on time" is called the pulse width. To get varying analog values, you change, or modulate, that pulse width. If you repeat this on-off pattern fast enough with an LED for example, the result is as if the signal is a steady voltage between 0 and 5v controlling the brightness of the LED.

18. How PWM works!

19. Example of PWM Have you ever seen the “snoozing LED” on some laptops when they’re in sleep mode? This is done by varying the WIDTH of the digital pulse sent to the LED. It starts at a low value and steadily ramps up the width then then steadily reduces the width In short terms = over a few seconds, ramp the duty cycle to 100, then over a few more seconds, ramp the duty cycle back to zero.

20. Relays A relay is just an electronic switch!

21. Basic Transistor Operation Transistors can be one of two things: –A SWITCH –AN AMPLIFIER

22. Types of Transistors

23. Transistor Legs (yeah) E is for EMITTER B IS FOR BASE C IS FOR COLLECTOR

24. Acting as a switch This is the most common behavior for Arduino purposes.