1. Network Devices & Wiring Geert Jan de Groot

2. Network Wiring Half/full duplex Ethernet Network Wiring Autonegotiation Structured wiring Optics

3. Half duplex Ethernet is CSMA/CD (Carrier Sense Multiple Access/Collision Detection) Only one station transmitting simultaniously Listen before you transmit Listen while you transmit

4. Half duplex (2) If there is a collision, both transmitters will: –Jam –Backoff (exponentially, randomly) –Re-try sending the packet –Minimal packet size: 64 bytes Collisions are harmless! –Actually help scale / stabilize an ethernet network

5. Full duplex Allows transmission/reception simultaniously –Impossible on older coax media –Easy to implement on twisted pair/fiber media No collisions More bandwith available

6. Copper Ethernet media Coax (10 Mbit/sec) –now obsolete Twisted pair –Uses pair 1-2, 3-6, 4-5, 7-8 –10 Mbit/sec (10BASE-T) –100 Mbit/sec –1000 Mbit/sec (‘gigabit ethernet’) –(10.000 Mbit/sec)

7. A few words on 10BASE-T Available everywhere today Uses pair 1-2, 3-6 –Unshielded twisted pairs –Often miswired Typically half-duplex –Full duplex possible Max length 100 meters!

8. 10BASE-T cables Normal cable Used from host to hub Crossover cable Used hub to hub or host to host Some hubs have built-in crossovers

9. 100 Mbit copper networks 3 standards: –100BASE-TX <<-- Winner –100BASE-T4 –100VG-Anylan Requires Category 5 (‘CAT5’) cabling –No more, no less 100BASE-TX runs on 2 wire pairs –1-2, 3-6, like 10BASE-T Cheap today

10. Faster: Gigabit Ethernet 1000 Mbit/sec, 1000BASE-T Still works on CAT5 cabling –Tight fit Uses all 4 wire pairs –In both directions About to get cheap and common –$35 SRP for a gigabit network card Automatic crossover additional new feature

11. Gigabit Ethernet and packet size Faster ethernet historically kept 1500 byte packet size –Made bridging between speeds possible Part of gigabit industry wants bigger packets –Lower overhead, hence higher performance Bigger packets not part of standard –Unresolved issues –I believe wrong way to go

12. Future: 10 Gigabit Ethernet 10 Gigabit originally only on fiber 10 Gigabit on copper currently being investigated by IEEE 802.3 standards committee

13. Link pulses 10BASE-T sends link pulses when idle –used to test integrity of link –link light 100BASE-T uses faster link pulses –Automatic detection between 10 and 100 possible Manual setting of half/full duplex –Settings must match

14. Autonegotiation Method to automatically select ‘best’ transmission method between link partners Link pulse now becomes pulse train Automatically sets speed, duplex etc

15. Autonegotiation (2) ‘Parallel detection’ for devices w/o autonegotiation –10BASE-T and 100BASE-TX only –Only HDX Autonegotiation mandatory for gigabit ethernet Technology is mature now –Early chips had serious issues, so be aware

16. Autonegotiation failure mode One end set to fixed 100Mbit, Full-Duplex Other end uses autonegotiation What happens? 100Mbit FDX Autonegotiation

17. Structured wiring “Everything over the same wiring”

18. Wire Types Category 3: 10 Mbps Category 4: 16 Mbps (for token ring) Category 5: 100 Mbps / 1000 Mbps Shielded or unshielded Advice: use Cat 5 UTP (unshielded twisted pair) Category 6, 7 and higher marketing hype –Not official IEEE spec

19. Structured wiring pitfalls High installation cost –so install enough the first time Use materials that are qualified for Cat 5 Get guarantee from installer

20. Fiber optics Must use fiber between buildings –Cable length restrictions –Lightning protection Multi mode: short hauls Single mode: long hauls

21. Fiber optics (2) Different fiber diameters Different connector types –ST generally ‘older’ 10mbit stuff –SC newer, generally 100mbit –VF45 –Others

22. Fiber optics (3) 10BASE-F for 10Mbps ethernet 100BASE-FX for 100Mbps fast ethernet 1000BASE-SX/LX for gigabit ethernet No autonegotiation –Colours are different –HDX doesn’t make sense Advice: run more fibers than you need, but don’t terminate them (yet)

23. Hubs, Switches and Routers How do they work? What are the differences?

24. Packet headers IPTCPDataEther EdstT IPdstIPsrc Network devices may use {ether, IP} headers to do it’s job (sometimes in twisted ways) Esrc

25. Ethernet hub Hub

26. Ethernet hub (2) Hub is layer 1 device Hub does not filter packets Whole hub is one collision domain Daisychaining of hubs limited Cheap Doesn’t exist for Gigabit Ethernet

27. Ethernet Switch Switch

28. Ethernet Switch (2) Switch looks at ethernet headers (layer 2) –ethernet to ethernet only Learns what addresses are connected to which ports If destination of packet known, the packet is only sent to the destination port

29. Ethernet Switch (3) Each port is a separate collision domain –no daisychain limit Often one host per port –high performance Security features Dualspeed ‘hub’ includes switch

30. Router

31. Router (2) Router works on IP header (layer 3) Can use almost any underlying media –LAN or WAN Can have several ports Useful for long distance connections (backbone) Must be configured –IP addresses etc.

32. .