1. CPS120: Introduction to Computer Science Midterm Exam Review

2. Introduction To Computers

20. Machine Language Every processor type has its own set of specific machine instructions The relationship between the processor and the instructions it can carry out is completely integrated Each machine-language instruction does only one very low-level task

21. Assembly Language Assembly languages: assign mnemonic letter codes to each machine-language instruction –The programmer uses these letter codes in place of binary digits –A program called an assembler reads each of the instructions in mnemonic form and translates it into the machine-language equivalent

22. Instruction Format Difference between immediate-mode and direct-mode addressing

23. Some Sample Instructions Subset of Pep/7 instructions

24. Figure 7.5 Assembly Process

25. Algorithm and Program Design

26. Top-Down Design This process continues for as many levels as it takes to expand every task to the smallest details A step that needs to be expanded is an abstract step An example of top-down design

27. A General Example Planning a large party Subdividing the party planning

28. Flowchart A graphical representation of an algorithm.

29. Pseudocode Uses a mixture of English and formatting to make the steps in the solution explicit

30. Logic Flowcharts These represent the flow of logic in a program and help programmers “see” program design.

31. Terminator. Shows the starting and ending points of the program. A terminator has flow lines in only one direction, either in (a stop node) or out (a start node). Data Input or Output. Allows the user to input data and results to be displayed. Processing. Indicates an operation performed by the computer, such as a variable assignment or mathematical operation. With a heading – an internal subroutine Decision. The diamond indicates a decision structure. A diamond always has two flow lines out. One flow lineout is labeled the “yes” branch and the other is labeled the “no” branch. Predefined Process. One statement denotes a group of previously defined statements. Such as a function or a subroutine created externally Connector. Connectors avoid crossing flow lines, making the flowchart easier to read. Connectors indicate where flow lines are connected. Connectors come in pairs, one with a flow line in and the other with a flow line out. Off-page connector. Even fairly small programs can have flowcharts that extend several pages. The off-page connector indicates the continuation of the flowchart on another page. Just like connectors, off-page connectors come in pairs. Flow line. Flow lines connect the flowchart symbols and show the sequence of operations during the program execution. Common Flowchart Symbols

32. How to Draw a Flowchart There are no hard and fast rules for constructing flowcharts, but there are guidelines which are useful to bear in mind.Here are six steps which can be used as a guide for completing flowcharts. 1.Describe the purpose of the program to be created (this is a one- line statement) 2.Start with a 'trigger' event (it may be the beginning of the program) 3.Initialize any values that need to be defined at the start of the program 4.Note each successive action concisely and clearly 5.Go with the main flow (put extra detail in other charts -- this is the basis of structured programming) 6.Follow the process through to a useful conclusion (end at a 'target' point -- like having no more records to process)

33. START Intialize variables LOOP While More records do READ record PROCESS record PRINT detail record ENDLOOP CALCULATE TOTALS PRINT total record END Pseudocode for a Generalized Program

34. Rules for Pseudocode 1.Make the pseudocode language-independent 2.Indent lines for readability 3.Make key words stick out by showing them capitalized, in a different color or a different font 4.Punctuation is optional 5.End every IF with ENDIF 6.Begin loop with LOOP and end with ENDLOOP 7.Show MAINLINE first; all others follow 8.TERMINATE all routines with an END instruction

35. Gates and Boolean Logic

36. Gates Six types of gates –NOT –AND –OR –XOR –NAND –NOR

37. NOT Gate A NOT gate accepts one input value and produces one output value Various representations of a NOT gate

38. NOT Gate By definition, if the input value for a NOT gate is 0, the output value is 1, and if the input value is 1, the output is 0

39. AND Gate An AND gate accepts two input signals If the two input values for an AND gate are both 1, the output is 1; otherwise, the output is 0 Various representations of an AND gate

40. OR Gate If the two input values are both 0, the output value is 0; otherwise, the output is 1 Figure 4.3 Various representations of a OR gate

41. XOR Gate XOR, or exclusive OR, gate –An XOR gate produces 0 if its two inputs are the same, and a 1 otherwise –Note the difference between the XOR gate and the OR gate; they differ only in one input situation –When both input signals are 1, the OR gate produces a 1 and the XOR produces a 0

42. XOR Gate Various representations of an XOR gate

43. NAND and NOR Gates The NAND and NOR gates are essentially the opposite of the AND and OR gates, respectively Various representations of a NAND gate Various representations of a NOR gate

44. Review of Gate Processing A NOT gate inverts its single input value An AND gate produces 1 if both input values are 1 An OR gate produces 1 if one or the other or both input values are 1

45. Review of Gate Processing (cont.) An XOR gate produces 1 if one or the other (but not both) input values are 1 A NAND gate produces the opposite results of an AND gate A NOR gate produces the opposite results of an OR gate

46. Adders At the digital logic level, addition is performed in binary Addition operations are carried out by special circuits called, appropriately, adders

47. Adders The result of adding two binary digits could produce a carry value Recall that 1 + 1 = 10 in base two A circuit that computes the sum of two bits and produces the correct carry bit is called a half adder

48. Adders Circuit diagram representing a half adder Two Boolean expressions: sum = A  B carry = AB Page 103

49. Adders A circuit called a full adder takes the carry- in value into account A full adder

50. Computer Mathematics

51. Representing Data The computer knows the type of data stored in a particular location from the context in which the data are being used; –i.e. individual bytes, a word, a longword, etc –01100011 01100101 01000100 01000000 Bytes: 99 (10, 101 (10, 68 (10, 64 (10 Two byte words: 24,445 (10 and 17,472 (10 Longword: 1,667,580,992 (10 ASCII: c, e, D, @

52. Alphanumeric Codes American Standard Code for Information Interchange (ASCII) –7-bit code –Since the unit of storage is a bit, all ASCII codes are represented by 8 bits, with a zero in the most significant digit H e l l o W o r l d 48 65 6C 6C 6F 20 57 6F 72 6C 64 ASCII is a subset of the Unicode character set

53. Decimal Equivalents Assuming the bits are unsigned, the decimal value represented by the bits of a byte can be calculated as follows: 1.Number the bits beginning on the right using superscripts beginning with 0 and increasing as you move left Note: 2 0, by definition is 1 2.Use each superscript as an exponent of a power of 2 3.Multiply the value of each bit by its corresponding power of 2 4.Add the products obtained

54. Binary to Hex Step 1: Form four-bit groups beginning from the rightmost bit of the binary number –If the last group (at the leftmost position) has less than four bits, add extra zeros to the left of the group to make it a four-bit group 0110011110101010100111 becomes 0001 1001 1110 1010 1010 0111 Step 2: Replace each four-bit group by its hexadecimal equivalent –19EAA7 (16 Note: Octal is done in groups of threes

55. Converting Decimal to Other Bases Step 1: Divide the number by the base you are converting to (r) Step 2: Successively divide the quotients by (r) until a zero quotient is obtained Step 3: The decimal equivalent is obtained by writing the remainders of the successive division in the opposite order in which they were obtained –Know as modulus arithmetic Step 4: Verify the result by multiplying it out

56. Representing Signed Numbers Remember, all numeric data is represented inside the computer as 1s and 0s –Arithmetic operations, particularly subtraction raise the possibility that the result might be negative Any numerical convention needs to differentiate two basic elements of any given number, its sign and its magnitude –Conventions Sign-magnitude Two’s complement One’s complement

57. Representing Negatives It is necessary to choose one of the bits of the “basic unit” as a sign bit –Usually the leftmost bit –By convention, 0 is positive and 1 is negative Positive values have the same representation in all conventions However, in order to interpret the content of any memory location correctly, it necessary to know the convention being used used for negative numbers

58. Sign-Magnitude For a basic unit of N bits, the leftmost bit is used exclusively to represent the sign The remaining (N-1) bits are used for the magnitude

59. Sign-magnitude Operations Addition of two numbers in sign-magnitude is carried out using the usual conventions of binary arithmetic –If both numbers are the same sign, we add their magnitude and copy the same sign –If different signs, determine which number has the larger magnitude and subtract the other from it. The sign of the result is the sign of the operand with the larger magnitude

60. One’s Complement Devised to make the addition of two numbers with different signs the same as two numbers with the same sign Positive numbers are represented in the usual way For negatives –STEP 1: Start with the binary representation of the absolute value –STEP 2: Complement all of its bits

61. One's Complement Operations –Treat the sign bit as any other bit –For addition, carry out of the leftmost bit is added to the rightmost bit – end-around carry

62. Two’s Complement Convention A positive number is represented using a procedure similar to sign-magnitude To express a negative number 1.Express the absolute value of the number in binary 2.Change all the zeros to ones and all the ones to zeros (called “complementing the bits”) 3.Add one to the number obtained in Step 2 –The range of negative numbers is one larger than the range of positive numbers –Given a negative number, to find its positive counterpart, use steps 2 & 3 above

63. Two’s Complement Operations Addition: –Treat the numbers as unsigned integers The sign bit is treated as any other number –Ignore any carry on the leftmost position Subtraction –Treat the numbers as unsigned integers –If a "borrow" is necessary in the leftmost place, borrow as if there were another “invisible” one- bit to the left of the minuend