1. doc.: IEEE 802.11-13/1153r0 Submission September 2013 Laurent Cariou (Orange)Slide 1 Simulation scenario proposal Date: 2013-17-09 Authors:

2. doc.: IEEE 802.11-13/1153r0 Submission Context Simulation scenarios definition is a key step to clearly scope the work in HEW. We need to ensure that they address the real issues (scenario / interference / traffic model) –while being simple enough –and being “open enough” to not preclude parts of the potential solution space We take the assumptions that HEW will have to ensure improvements in « all main scenarios » –we can therefore spread the difference interference issues over the different scenarios In this presentation, we review the main simulation scenarios and –allocate specific interference condition problems to specific scenario(s) –define some options in the scenarios to capture all elements that can impact the performance of specific solutions Slide 2Laurent Cariou (Orange) September 2013

3. doc.: IEEE 802.11-13/1153r0 Submission Define simulation scenarios to capture all issues and to enable solutions evaluation 1 Need to make sure that all interference conditions are captured and spread over the different scenarios 2Need to enable PHY/MAC simulation parameters to be tuned, not to restrict the solution space (e.g. TxPower, channel selection…) 3 Need to include different options in the simulation scenarios so that, for the evaluation of specific schemes, all traffic or devices, that can have an impact on the performance, are taken into account –these options should be assigned to specific family of solutions as part of the evaluation methodology/selection procedure Slide 3Laurent Cariou (Orange) September 2013

4. doc.: IEEE 802.11-13/1153r0 Submission 1 Mapping of interference types on the main simulation scenarios We review the types of interference defined in the usage model document, and evaluate if they are captured in the current simulation scenarios –We base our analysis on document 1000r0, and mapped previous propositions, especially 722-23r0 The parameters that currently define the interference scenario are mostly the topology (AP/STA placements, channel conditions…) and whether the network is managed or not –By managed, it is meant that multiple APs are sharing the same management entity –But more importantly for simulation scenario definition: a managed network is planned, meaning that the AP locations follow a relatively regular grid and that specific frequency reuse schemes can be applied. Slide 4Laurent Cariou (Orange) September 2013

5. doc.: IEEE 802.11-13/1153r0 Submission 1 Mapping of interference types on the main simulation scenarios 1 Residential: –fully unmanaged (unplanned) networks, potentially overlaid by some P2P links –topology: High density of BSS, low to medium STA density, indoor 2a Enterprise: –Managed (planned) ESS overlaid by many unmanaged P2P links –topology: high density of BSSs, high density of STAs, indoor 2b Dense indoor hotspot: –Managed ESS (currently no overlaid interference proposed) –topology: High density of BSSs, high density of STAs, indoor 3a Outdoor large deployment: –managed ESS (currently no overlaid interference proposed) –topology: relatively low density of BSSs, high density of STAs, outdoor Slide 5Laurent Cariou (Orange) September 2013

6. doc.: IEEE 802.11-13/1153r0 Submission 1 Mapping of interference types on the main simulation scenarios Interference in unplanned deployments Interference between OBSSs belonging to the same planned ESS (cell-edge with low SNR) Interference between OBSSs belonging to the same planned ESS (cell-edge with high SNR) Interference from P2P unmanaged OBSS on a planned ESS interference from multiple overlapping planned ESSs Residential captured (723) Enterprise captured (723) not captured Dense Hotspot captured (723) not yet captured not captured Outdoor large deployment captured (723) not captured not yet captured Slide 6Laurent Cariou (Orange) September 2013

7. doc.: IEEE 802.11-13/1153r0 Submission 1 Mapping of interference types on the main simulation scenarios: Focus on dense hotspot 2b As the dense hotspot scenario is managed, we consider a frequency reuse deployment ICD is low (10-20m) Interference between BSSs belonging to the same planned ESS is important and well captured BSS simulation of all channels with frequency reuse 3 Simplified simulation: One channel only, assuming frequency reuse 3 CCA range STAs are concentrated close to the AP: good SNR at cell-edge Slide 7Laurent Cariou (Orange) September 2013

8. doc.: IEEE 802.11-13/1153r0 Submission We should add interfering networks to the dense hotspot scenario –overlay of BSS short-range links (for tethering devices) –randomly distributed on the whole simulation zone some of these BSS can be idle and only transmit management frames –Note that there are similarities with Enterprise 2a BSS 1 Mapping of interference types on the main simulation scenarios: Focus on dense hotspot 2b Slide 8Laurent Cariou (Orange) September 2013

9. doc.: IEEE 802.11-13/1153r0 Submission As the outdoor large hotspot scenario is managed, we consider a frequency reuse deployment as well ICD is large: 100-150m With this frequency reuse, interference between BSSs from the managed network is very low BSS All channels with frequency reuse 3 One channel with frequency reuse 3 CCA range STAs are distributed on the whole AP coverage: low SNR at cell-edge 1 Mapping of interference types on the main simulation scenarios: Focus on large outdoor 3a Slide 9Laurent Cariou (Orange) September 2013

10. doc.: IEEE 802.11-13/1153r0 Submission Potential interfering network on outdoor hotspot –overlay of other operators will be very common in such scenarios and is the most different interference from other scenarios –in the case of an overlay of 3 operators planned deployments, each of which with freq reuse 3, the scenario becomes a simple theoretical frequency reuse 1 deployment with 100-150m ICD between neighboring OBSSs with an overlap between neighboring cell around cell-edge (low SNR) with neighboring cells not sharing the same management entity with constraint on associations: STAs connect only to one operator APs BS S 1 operator 2 operators 3 operators BS S frequency reuse 1 deployment 1 Mapping of interference types on the main simulation scenarios: Focus on large outdoor 3a Slide 10Laurent Cariou (Orange) September 2013

11. doc.: IEEE 802.11-13/1153r0 Submission 2 Allow parameters tuning to evaluate technical propositions We all agree that on each scenarios, we should define a default value for all parameters –to define a baseline to compare with –Once we agree on the template (1001rx) for simulation scenario, we’ll make a proposal based on previous slides for this Now some of those parameters are key to the scenario definition and shouldn’t be tuned –AP/STA positioning, channel models… –channel and potentially bandwidth allocation for planned deployments (dense hotspot and outdoor large deployment) Depending on the proposed technical solutions, some parameters need to be tunable, as their adaptation is part of the solution space –Tx Power, CCA level, CSMA parameters, bandwidth, channels… Slide 11Laurent Cariou (Orange) September 2013

12. doc.: IEEE 802.11-13/1153r0 Submission 3 Define options in the simulation scenarios: proportion of HEW and legacy devices For all the technical propositions, especially for OBSS, we need to model all elements that could jeopardize the performance of the scheme (to ensure it will keep its efficiency in real deployments) If the presence of « legacy devices » is susceptible to have such degrading impact : –It will be important to define a proportion (TBD%) of devices in the scenario that won’t implement the proposed scheme and would keep the baseline default parameters STAs connected to the planned network APs and STAs part of the interfering network –whether this is mandatory or not should be determined by the group on a per solution basis as part of the evaluation methodology/selection procedure This « optional/mandatory » mix of devices should be defined in the simulation scenario Slide 12Laurent Cariou (Orange) September 2013

13. doc.: IEEE 802.11-13/1153r0 Submission 3 Define options in the simulation scenarios: proportion of HEW and legacy devices Example with Transmit power control and CCA control For example, power control solutions are showing promising theoretical gains in dense deployments However, it is well understood that the use of different power or CCA levels by devices leads to throughput starvation of certain nodes due to the introduction of asymmetric links –some power control solutions can therefore become inefficient if applied only in the AP but not on STA side in the presence of overlapping BSSs (P2P links) which don’t apply TPC, or apply it differently if only part of the traffic is applying TPC (APs could apply TPC for data transmission but not for management frames) If we want to make sure that such a proposed solution is efficient in real deployments, we would need to capture these degrading elements in the simulation scenarios : –proportion of devices (connected STAs and AP/STAs from the interfering networks) that don’t implement TPC and use « default » TxPower –idle AP/STAs that don’t apply TPC to their management frames transmission Slide 13Laurent Cariou (Orange) September 2013

14. doc.: IEEE 802.11-13/1153r0 Submission Conclusion We propose a design for dense hotspot 2b and outdoor large BSS 3a scenario –we’ll use template 1001rx (if/when agreed by the group) to make a proposition for default parameters for these scenarios, based on the current presentation Enabling parameter tuning by HEW devices in these scenarios should of course be enabled with some restrictions depending on the scenarios Options should be defined in the scenarios in order to capture all traffic or types of devices that can have an impact on specific solutions –Example for the mix of HEW and legacy devices for TPC solutions In the evaluation methodology/selection procedure, each family of proposed solutions should be linked to specific simulation scenario(s) and their option(s) –to ensure a good quality of the evaluation –to be able to compare competing solutions Slide 14Laurent Cariou (Orange) September 2013

15. doc.: IEEE 802.11-13/1153r0 Submission References 11-13/1000, “HEW simulation scenarios”, Simone Merlin (Qualcomm) 11-13/1001, “HEW simulation scenarios document template”, Simone Merlin (Qualcomm) 11-13/0722, “HEW Evaluation Methodology”, Minyoung Park (Intel) 11-13/0723, “HEW SG evaluation methodology overview” Minyoung Park (Intel) 11-13/1051, “HEW evaluation methodology” Ron Porat (Broadcom) September 2013 Slide 15Laurent Cariou (Orange)