1. Transport Layer3-1 Data Communication and Networks Lecture 7 Transport Protocols: TCP October 21, 2004

2. Transport Layer3-2 TCP: Overview RFCs: 793, 1122, 1323, 2018, 2581 r full duplex data: m bi-directional data flow in same connection m MSS: maximum segment size r connection-oriented: m handshaking (exchange of control msgs) init’s sender, receiver state before data exchange r flow controlled: m sender will not overwhelm receiver r point-to-point: m one sender, one receiver r reliable, in-order byte steam: m no “message boundaries” r pipelined: m TCP congestion and flow control set window size r send & receive buffers

3. Transport Layer3-3 TCP segment structure source port # dest port # 32 bits application data (variable length) sequence number acknowledgement number Receive window Urg data pnter checksum F SR PAU head len not used Options (variable length) URG: urgent data (generally not used) ACK: ACK # valid PSH: push data now (generally not used) RST, SYN, FIN: connection estab (setup, teardown commands) # bytes rcvr willing to accept counting by bytes of data (not segments!) Internet checksum (as in UDP)

4. Transport Layer3-4 TCP seq. #’s and ACKs Seq. #’s: m byte stream “number” of first byte in segment’s data ACKs: m seq # of next byte expected from other side m cumulative ACK Q: how receiver handles out-of-order segments m A: TCP spec doesn’t say, - up to implementor Host A Host B Seq=42, ACK=79, data = ‘C’ Seq=79, ACK=43, data = ‘C’ Seq=43, ACK=80 User types ‘C’ host ACKs receipt of echoed ‘C’ host ACKs receipt of ‘C’, echoes back ‘C’ time simple telnet scenario

5. Transport Layer3-5 Timing Problem! The delay required for data to reach a destination and an acknowledgment to return depends on traffic in the internet as well as the distance to the destination. Because it allows multiple application programs to communicate with multiple destinations concurrently, TCP must handle a variety of delays that can change rapidly. How does TCP handle this.....

6. Transport Layer3-6 Solving Timing Problem r Keep estimate of round trip time on each connection r Use current estimate to set retransmission timer r Known as adaptive retransmission r Key to TCP’s success

7. Transport Layer3-7 TCP Round Trip Time and Timeout Q: how to set TCP timeout value? r longer than RTT m but RTT varies r too short: premature timeout m unnecessary retransmissions r too long: slow reaction to segment loss Q: how to estimate RTT?  SampleRTT : measured time from segment transmission until ACK receipt m ignore retransmissions  SampleRTT will vary, want estimated RTT “smoother”  average several recent measurements, not just current SampleRTT

8. Transport Layer3-8 TCP Round Trip Time and Timeout EstimatedRTT = (1-  )*EstimatedRTT +  *SampleRTT r Exponential weighted moving average r influence of past sample decreases exponentially fast  typical value:  = 0.125

9. Transport Layer3-9 Example RTT estimation:

10. Transport Layer3-10 TCP Round Trip Time and Timeout Setting the timeout  EstimtedRTT plus “safety margin”  large variation in EstimatedRTT -> larger safety margin r first estimate of how much SampleRTT deviates from EstimatedRTT: TimeoutInterval = EstimatedRTT + 4*DevRTT DevRTT = (1-  )*DevRTT +  *|SampleRTT-EstimatedRTT| (typically,  = 0.25) Then set timeout interval:

11. Transport Layer3-11 TCP reliable data transfer r TCP creates rdt service on top of IP’s unreliable service r Pipelined segments r Cumulative acks r TCP uses single retransmission timer r Retransmissions are triggered by: m timeout events m duplicate acks r Initially consider simplified TCP sender: m ignore duplicate acks m ignore flow control, congestion control

12. Transport Layer3-12 TCP sender events: data rcvd from app: r Create segment with seq # r seq # is byte-stream number of first data byte in segment r start timer if not already running (think of timer as for oldest unacked segment)  expiration interval: TimeOutInterval timeout: r retransmit segment that caused timeout r restart timer Ack rcvd: r If acknowledges previously unacked segments m update what is known to be acked m start timer if there are outstanding segments

13. Transport Layer3-13 TCP: retransmission scenarios Host A Seq=100, 20 bytes data ACK=100 time premature timeout Host B Seq=92, 8 bytes data ACK=120 Seq=92, 8 bytes data Seq=92 timeout ACK=120 Host A Seq=92, 8 bytes data ACK=100 loss timeout lost ACK scenario Host B X Seq=92, 8 bytes data ACK=100 time Seq=92 timeout SendBase = 100 SendBase = 120 SendBase = 120 Sendbase = 100

14. Transport Layer3-14 TCP retransmission scenarios (more) Host A Seq=92, 8 bytes data ACK=100 loss timeout Cumulative ACK scenario Host B X Seq=100, 20 bytes data ACK=120 time SendBase = 120

15. Transport Layer3-15 TCP ACK generation [RFC 1122, RFC 2581] Event at Receiver Arrival of in-order segment with expected seq #. All data up to expected seq # already ACKed Arrival of in-order segment with expected seq #. One other segment has ACK pending Arrival of out-of-order segment higher-than-expect seq. #. Gap detected Arrival of segment that partially or completely fills gap TCP Receiver action Delayed ACK. Wait up to 500ms for next segment. If no next segment, send ACK Immediately send single cumulative ACK, ACKing both in-order segments Immediately send duplicate ACK, indicating seq. # of next expected byte Immediate send ACK, provided that segment startsat lower end of gap

16. Transport Layer3-16 Fast Retransmit r Time-out period often relatively long: m long delay before resending lost packet r Detect lost segments via duplicate ACKs. m Sender often sends many segments back-to- back m If segment is lost, there will likely be many duplicate ACKs. r If sender receives 3 ACKs for the same data, it supposes that segment after ACKed data was lost: m fast retransmit: resend segment before timer expires

17. Transport Layer3-17 TCP Flow Control r receive side of TCP connection has a receive buffer: r speed-matching service: matching the send rate to the receiving app’s drain rate r app process may be slow at reading from buffer sender won’t overflow receiver’s buffer by transmitting too much, too fast flow control

18. Transport Layer3-18 TCP Flow control: how it works (Suppose TCP receiver discards out-of-order segments)  spare room in buffer = RcvWindow = RcvBuffer-[LastByteRcvd - LastByteRead]  Rcvr advertises spare room by including value of RcvWindow in segments  Sender limits unACKed data to RcvWindow m guarantees receive buffer doesn’t overflow

19. Transport Layer3-19 TCP Connection Management Recall: TCP sender, receiver establish “connection” before exchanging data segments r initialize TCP variables: m seq. #s  buffers, flow control info (e.g. RcvWindow ) r client: connection initiator Socket clientSocket = new Socket("hostname","port number"); r server: contacted by client Socket connectionSocket = welcomeSocket.accept(); Three way handshake: Step 1: client host sends TCP SYN segment to server m specifies initial seq # m no data Step 2: server host receives SYN, replies with SYNACK segment m server allocates buffers m specifies server initial seq. # Step 3: client receives SYNACK, replies with ACK segment, which may contain data

20. Transport Layer3-20 TCP Connection Management (cont.) Closing a connection: client closes socket: clientSocket.close(); Step 1: client end system sends TCP FIN control segment to server Step 2: server receives FIN, replies with ACK. Closes connection, sends FIN. client FIN server ACK FIN close closed timed wait

21. Transport Layer3-21 TCP Connection Management (cont.) Step 3: client receives FIN, replies with ACK. m Enters “timed wait” - will respond with ACK to received FINs Step 4: server, receives ACK. Connection closed. Note: with small modification, can handle simultaneous FINs. client FIN server ACK FIN closing closed timed wait closed

22. Transport Layer3-22 TCP Connection Management (cont) TCP client lifecycle TCP server lifecycle

23. Transport Layer3-23 Implementation Policy Options r Send r Deliver r Accept r Retransmit r Acknowledge

24. Transport Layer3-24 Send r If no push or close TCP entity transmits at its own convenience (IFF send window allows!) r Data buffered at transmit buffer r May construct segment per data batch r May wait for certain amount of data

25. Transport Layer3-25 Deliver (to application) r In absence of push, deliver data at own convenience r May deliver as each in-order segment received r May buffer data from more than one segment

26. Transport Layer3-26 Accept r Segments may arrive out of order r In order m Only accept segments in order m Discard out of order segments r In windows m Accept all segments within receive window

27. Transport Layer3-27 Retransmit r TCP maintains queue of segments transmitted but not acknowledged r TCP will retransmit if not ACKed in given time m First only m Batch m Individual

28. Transport Layer3-28 Acknowledgement r Immediate m as soon as segment arrives. m will introduce extra network traffic m Keeps sender’s pipe open r Cumulative m Wait a bit before sending ACK (called “delayed ACK”) m Must use timer to insure ACK is sent m Less network traffic m May let sender’s pipe fill if not timely!