Project 3: Beakman’s Motor

Project 3: Beakman’s Motor
Part A: Background Part B: Building the Basic Motor Part C: Designing an Improved Motor Part D: Building and Testing an Improved Motor

Electronic Instrumentation
Beakman’s Motor Websites: 18 October 2003 Electronic Instrumentation

Task List Build the basic motor Demonstrate that it will run for at least 30 seconds Take data that verifies the rpm of the motor Take data on the components of the system Improve the motor design, build and test it Demonstrate that the motor works for at least 30 seconds without springs Demonstrate that the motor works for at least 30 seconds with springs Take data that verifies the rpm of the motor for both cases Take data on the components of the new system 18 October 2003 Electronic Instrumentation

Materials Required One D-Cell Battery (Supply your own – fresh batteries provide more power.) One Wide Rubber Band Two Large Paper Clips One or Two Circular Ceramic Magnets (or equivalent) Magnet Wire (the kind with enamel insulation) One Toilet Paper Tube (or paper tube) Fine Sandpaper and wooden block for sanding surface Optional: Glue, small block of wood for base, battery holder, protoboard … DC Power Supplies, Oscilloscope, and other instruments 18 October 2003 Electronic Instrumentation

Magnetism One of the first compasses, a fish shaped iron leaf was mentioned in the Wu Ching Tsung Yao written in 1040 Trinity College, Dublin 18 October 2003 Electronic Instrumentation

Animal Magnetism A frog suspended in an intense magnetic field – all of us are paramagnetic Much money is wasted on magnetic therapy 18 October 2003 Electronic Instrumentation

Electromagnetic Revolution
These four equations epitomize the electromagnetic revolution. Richard Feynman claimed that "ten thousand years from now, there can be little doubt that the most significant event of the 19th century will be judged as Maxwell's discovery of the laws of electrodynamics" 18 October 2003 Electronic Instrumentation

Magnetic Attraction It is possible to produce motion using magnetic attraction and/or repulsion Either permanent magnets or electromagnets or both can be used 18 October 2003 Electronic Instrumentation

Magnetic Attraction and Repulsion
One of the many facts we all recall from our earliest science education 18 October 2003 Electronic Instrumentation

DC Motors The stator is the stationary outside part of a motor. The rotor is the inner part which rotates. In the motor animations, red represents a magnet or winding with a north polarization, while green represents a magnet or winding with a south polarization. Opposite, red and green, polarities attract. 18 October 2003 Electronic Instrumentation

DC Motors Just as the rotor reaches alignment, the brushes move across the commutator contacts and energize the next winding. In the animation the commutator contacts are brown and the brushes are dark grey. A yellow spark shows when the brushes switch to the next winding. 18 October 2003 Electronic Instrumentation

DC Motor Applications Automobiles Windshield Wipers Door locks Window lifts Antenna retractor Seat adjust Mirror adjust Anti-lock Braking System Cordless hand drill Electric lawnmower Fans Toys Electric toothbrush Servo Motor 18 October 2003 Electronic Instrumentation

Beakman’s Motor A simple DC motor with brushes made with a battery, two paperclips, a rubber band and about 1 meter of enameled wire. 18 October 2003 Electronic Instrumentation

Building Beakman’s Motor
Watch the Movie The two most important sites with instructions on how to build the motor 18 October 2003 Electronic Instrumentation

Measuring the Speed As the coil rotates, it connects to the power supply about half the time. When this occurs, the voltage measured at the battery or power supply will drop (voltage divider action). Thus, a series of pulses will be observed, which can be used to determine the frequency of revolution. 18 October 2003 Electronic Instrumentation

Measuring the Speed Battery Voltage Voltage measured across the battery 18 October 2003 Electronic Instrumentation

Measuring the Speed Good data should show consistent pulses. Note that the duty cycle is still not good in this case. Poor data shows erratic contact is being made 18 October 2003 Electronic Instrumentation

Brushless DC Motors A brushless dc motor has a rotor with permanent magnets and a stator with windings. It is essentially a dc motor turned inside out. The control electronics replace the function of the commutator and energize the proper winding. 18 October 2003 Electronic Instrumentation

Brushless DC Motor Applictions
Medical: centrifuges, orthoscopic surgical tools, respirators, dental surgical tools, and organ transport pump systems Model airplanes, cars, boats, helicopters Microscopes Tape drives and winders Artificial heart 18 October 2003 Electronic Instrumentation

Full Stepper Motor This animation demonstrates the principle for a stepper motor using full step commutation. The rotor of a permanent magnet stepper motor consists of permanent magnets and the stator has two pairs of windings. Just as the rotor aligns with one of the stator poles, the second phase is energized. The two phases alternate on and off and also reverse polarity. There are four steps. One phase lags the other phase by one step. This is equivalent to one forth of an electrical cycle or 90°. 18 October 2003 Electronic Instrumentation

Half Stepper Motor This animation shows the stepping pattern for a half-step stepper motor. The commutation sequence for a half-step stepper motor has eight steps instead of four. The main difference is that the second phase is turned on before the first phase is turned off. Thus, sometimes both phases are energized at the same time. During the half-steps the rotor is held in between the two full-step positions. A half-step motor has twice the resolution of a full step motor. It is very popular for this reason. 18 October 2003 Electronic Instrumentation

Stepper Motors This stepper motor is very simplified. The rotor of a real stepper motor usually has many poles. The animation has only ten poles, however a real stepper motor might have a hundred. These are formed using a single magnet mounted inline with the rotor axis and two pole pieces with many teeth. The teeth are staggered to produce many poles. The stator poles of a real stepper motor also has many teeth. The teeth are arranged so that the two phases are still 90° out of phase. This stepper motor uses permanent magnets. Some stepper motors do not have magnets and instead use the basic principles of a switched reluctance motor. The stator is similar but the rotor is composed of a iron laminates. 18 October 2003 Electronic Instrumentation

More on Stepper Motors Note how the phases are driven so that the rotor takes half steps 18 October 2003 Electronic Instrumentation

More on Stepper Motors Animation shows how coils are energized for full steps 18 October 2003 Electronic Instrumentation

More on Stepper Motors Full step sequence showing how binary numbers can control the motor Half step sequence of binary control numbers 18 October 2003 Electronic Instrumentation

Stepper Motor Applications
Film Drive Optical Scanner Printers ATM Machines I. V. Pump Blood Analyzer FAX Machines Thermostats 18 October 2003 Electronic Instrumentation

MEMS Micro-Electro-Mechanical Systems (MEMS) is the integration of mechanical elements, sensors, actuators, and electronics on a common silicon substrate through the utilization of microfabrication technology. While the electronics are fabricated using integrated circuit (IC) process sequences (e.g., CMOS, Bipolar, or BICMOS processes), the micromechanical components are fabricated using compatible "micromachining" processes that selectively etch away parts of the silicon wafer or add new structural layers to form the mechanical and electromechanical devices. 18 October 2003 Electronic Instrumentation

MEMS Stepper Motor This motor is very much like the other stepper motors mentioned above, except that it is 2D and very small 18 October 2003 Electronic Instrumentation

MEMS Rotary motor Steam Engine (single piston) 18 October 2003 Electronic Instrumentation

RPI MEMS Faculty Prof. Yoav Peles Prof. Borca-Tasçiuc Prof. Harry Stephanou Prof. Kevin Craig 18 October 2003 Electronic Instrumentation

Project 3 Requirements Motors must be built using a 1.5 volt battery or 1.5 Volts DC from the power supply. You must use the magnet wire and magnets available in the studio. Supports must be made from paper clips The cradle must have one open end. It cannot have any complete loops. No more than 2 magnets & the magnets must be the ones supplied. You can use the protoboard and a battery holder. Springs must either be made of non-conducting material or not connected to source. 18 October 2003 Electronic Instrumentation

Project 3 Requirements You cannot use your hands to hold the spring or hold the motor in the cradle. That is, you cannot touch the motor during its test. You cannot use creative sanding to create a double duty cycle. Your motor must run for 30 seconds. Use the wooden blocks for sanding. Students caught sanding tables lose 1 point each time. Clean up. Be careful not to drop long thin wires on the floor, they ruin the vacuum cleaners. Groups that leave their areas in a mess will lose 1 point each time. 18 October 2003 Electronic Instrumentation

Additional Changes Anything else in the basic design can be changed. For example, the coil can be any size with any number of turns using any size wire and the paper clips can be bent into any shape as long as the top of the cradle remains open. Also, other materials can be added. For example, a small wire (spring) can be used to hold the coil in the cradle as long as it is not connected electrically to the cradle. Final performance testing must be done with either the battery or the DC power supply and speeds witnessed and recorded. Any design ideas that deviate significantly from the basic Beakman’s motor should be discussed with the instructor. 18 October 2003 Electronic Instrumentation

Springs Students have been able to obtain some very fast speeds by manually pressing down on the coil axle with two pieces of wire (4-6 inches in length). That is, they hold the two pieces of wire in their hands and press gently down onto the coil axle as close to the support point as possible. This stops the coil from hopping and maintains the connection between the coil and the paper clip support. This semester, you are required to use a somewhat more elegant approach and use a spring that requires no human intervention. For example, you can attach one end of these extra wires to a stand and then bend them in such a manner to create a spring that holds the axle down without requiring a person to hold the wires. You can use any design you wish for your spring as long as the metal of the spring does not make electrical contact between the coil and the battery. Any kind of insulated wire can be used as long as the insulation is not removed. Using a spring of this type will take some adjustment to get it right – something that is not required for a human operated spring, since we are capable of adjusting the tension until the best possible speed is achieved. When you test your motor, you should do it first without the spring. When you add the wires you should see that the motor rotates at a much higher frequency and that the coil remains in contact with the support for a larger fraction of each cycle (that is, that the duty cycle is larger). 18 October 2003 Electronic Instrumentation

Extra Credit Opportunities
Exceptionally creative approaches to implementation or in the final design If your motor is one of the fastest in the section, you will be eligible for an additional point Engineering problems are often solved by experimenting with different types of configurations, finding which changes have the most positive effects, and systematically choosing a course of action based on those experiments 18 October 2003 Electronic Instrumentation

Battery Resistance Just like the function generator, batteries all have some kind of internal impedance. By connecting the battery to a known resistor and measuring the resulting voltage, it is possible to determine the internal resistance. 18 October 2003 Electronic Instrumentation

Note 18 October 2003 Electronic Instrumentation

Variations with Manufacturer
(AA Batteries) 18 October 2003 Electronic Instrumentation

Discharging 18 October 2003 Electronic Instrumentation

Additional Battery Information
(source of data on previous slides) 18 October 2003 Electronic Instrumentation

Practical Questions You should be able to describe the goal and the methodology of the project You should be able to explain how the motor works You should be able to discuss the design trade-offs for the motor You should be able to connect the circuits to the power supply and to the ‘scope. You should know how to use the scope without using the “Auto Scale” button You should be able to measure the frequency on the scope You should be able to capture the scope signal both as a picture and data, using Agilent Intuilink software You should be able to explain how the motor can be modeled You should be able to measure the components of the motor model 18 October 2003 Electronic Instrumentation

Project 3: Beakman’s Motor

Similar presentations

Presentation on theme: "Project 3: Beakman’s Motor"— Presentation transcript:

Similar presentations

About project

Feedback

Log in

Auth with social network:

Project 3: Beakman’s Motor

Similar presentations

Presentation on theme: "Project 3: Beakman’s Motor"— Presentation transcript:

Similar presentations

About project

Feedback