1. RAFT Radar Fence Transponder Phase 0/1 Safety Review 16 Dec 04 Bob Bruninga, PE MIDN 1/C Eric Kinzbrunner MIDN 1/C Ben Orloff MIDN 1/C Ben Orloff MIDN 1/C JoEllen Rose

2. RAFT Team  Spacecraft (US Naval Academy) Bob Bruninga (PI)Bob Bruninga (PI) MIDN 1/C Eric Kinzbrunner, MIDN 1/C Ben Orloff, MIDN 1/C JoEllen RoseMIDN 1/C Eric Kinzbrunner, MIDN 1/C Ben Orloff, MIDN 1/C JoEllen Rose  Launch Integration (Space Test Program) Chief Of Integration & Ops: Capt Yvonne FedeeChief Of Integration & Ops: Capt Yvonne Fedee Payload Manager: Mr Perry BallardPayload Manager: Mr Perry Ballard Back Up Payload Manager: Lt Reann CaldwellBack Up Payload Manager: Lt Reann Caldwell Payload Integration Engineer(PIE): Mr Carson TaylorPayload Integration Engineer(PIE): Mr Carson Taylor Launcher & Back Up PIE: Mr Scott RitterhouseLauncher & Back Up PIE: Mr Scott Ritterhouse Safety Engineer (SE): Ms. Theresa ShafferSafety Engineer (SE): Ms. Theresa Shaffer Launcher & Back up SE: Mr Darren BromwellLauncher & Back up SE: Mr Darren Bromwell

3.  Assumption: Launch NET February 2006 RAFT Kickoff Apr 04 RAFT Kickoff Apr 04 RAFT USNA SRR Sep 04 RAFT USNA SRR Sep 04 RAFT PDR19 Nov 04 RAFT PDR19 Nov 04 Launcher CDR Nov 04 Launcher CDR Nov 04  RAFT Phase 0/1 Safety16 Dec 04  RAFT CDR Feb 05  RAFT Phase 2 Safety Feb 05  RAFT Flight Unit Testing May 05  RAFT Phase 3 Safety Aug 05  RAFT Delivery/Install Oct 05  RAFT Flight (STS-116) 09 Feb 06 Key Milestones: Schedule

4. So Many CUBEsats 30 to 50 in Construction AIAA/USU Small Sat Conference 30% of papers were for PICO, NANO and CUBEsats All smaller than 10 cm How to Track them???

5. Mission Statement The mission of RAFT is:  To provide the Navy Space Surveillance (NSSS) radar fence with a means to determine the bounds of a constellation of PicoSats otherwise undetectable by the radar fence  To enable NSSS to independently calibrate their transmit and receive beams using signals from RAFT.  This must be accomplished with two PicoSats, one that will actively transmit and receive, and one with a passively augmented radar cross-section.  Additionally, RAFT will provide experimental communications transponders for the Navy Military Affiliate Radio System, the United States Naval Academy’s Yard Patrol crafts, and the Amateur Satellite Service.

6. NSSS Radar Fence

7. RAFT1 Mission Architecture

8. MARScom Mission Architecture

9. Military Affiliate Radio System The Mission of the MARS system is to:  Provide auxiliary communications for military, federal and local disaster management officials  Assist in effecting communications under emergency conditions.  Handle morale and quasi-official message and voice communications traffic for members of the Armed Forces and authorized U.S. Government civilian personnel  Provide routine operations in support of MARSGRAMS and … contacts between service personnel and their families back home.

10. Yard Patrol Craft Application Unique UHF AM Uplink and HF SSB downlink

11. RAFT1 and MARScom

13. Pass Geometry

14. Raft1 Block Diagram

15. MARScom Block Diagram

16. RAFT Lifetime Estimate 6.5 Months

17. MARScom Lifetime Estimate 4.9 Months

18. 1. NEA DEVICE ACTUATES 2. LATCH ROD SLIDES FORWARD 3. DOOR SWINGS OPEN AND LATCHES 4. PICOSATs EJECT 1 2 3 4 Door in open, latched, landing position SSPL4410 LAUNCHER: Operation NOTE: Top Cover and Latchtrain Cover not shown in this view No separation until after both picosats clear launcher

19. RAFT Deployment Velocity of CM: 1.00 m/s Velocity of RAFT: 0.57 m/s Velocity of MARScom: 1.57 m/s

20. Air Track Separation Test

21. IDEAS Model

23. Assembly

24. Solar Panel Design COTS Silicon Cells on PCB panel Covered with Clear Teflon Coating 1.5 Watt panel Mechanically rugged for rain/hail/birds PCsat Flight Heritage

25. Top Panel VHF Antenna holes HF whip hole Antenna pockets for other satellite

26. RAFT1 Internal Diagram Top View

27. RAFT Internal Diagram Corner Detail

28. Side Panel

29. Side Panel Detail Loaded Side.25” thick

30. Custom Side Panel for Antenna Crank and GSE Connector

31. For SSPL4410 with MEPSI: PICOSAT mass m = 1.6 kg = 3.5 lbs Preload > { 24 g x 3.5 lbs = 84 lbs } F = 125 lb max preload + 24 g x 3.5 lb  210 lbs 24 g calculated in SVP For SSPL5510 with RAFT: PICOSAT mass m = 7 kg = 15.4 lbs Preload > { 24 g x 15.4 lbs = 370 lbs } F = 500 lb max preload + 24 g x 15.4 lb  870 lbs SSPL4410 LAUNCHER: Preload and Launch Loads credit:

32. Structure Displacements

33. Depressurization Rate.040 hole Gives 2:1 margin for depresurization

34. Battery Box

35. RAFT Antenna Separation Mechanisms

36. RAFT Antenna Springs

37. Long-Wire Antenna

38. Electrical Systems And Connections Each panel one pigtail All plug into Interface Board on the PSK panel

39. Interface Board

40. EPS and Solar Power Budget

41. Raft1 Block Diagram

42. Solar Power Budget Conclusion: The PCsat panels per side of the satellite and a 39% eclipse time, an average available bus load of 0.96 watts will be available to the spacecraft.

43. RAFT1 Required Power Budget Whole Orbit Average 10% Depth of Discharge

44. MARScom Required Power Budget

45. Power System

46. Simplified Power System Charge in Parallel Transmit in Series Duty cycle 4%

47. Operations Safety Features All Transmitter circuits time-out to OFF

49. Post Cold Test Battery Condition (No Leakage)

50. Battery Cold Test Time Line

51. -60 °C Battery Tests Triple walled chamber Sealed for condensation Adding Dry Ice 30 Hour test @ -60C

52. -60 °C Battery Test: Thermal Conditions

53. Post -60 °C Charge Temp in Vacuum

54. Post Cold Test Discharge Current 852 mA-H

55. PCsat Solar Panel I-V Curve discharged Full charge

56. PCsat P-V Curve discharged Full charge

57. Dead Battery Charge Efficiency

58. Dead Battery Recovery Test

59. Communication  RAFT1 ITU Request Form submitted. TX: 145.825 MHz, 2 Watt, 20 KHz B/W FMTX: 145.825 MHz, 2 Watt, 20 KHz B/W FM RX: 29.400-29.403 MHz PSK-31 ReceiverRX: 29.400-29.403 MHz PSK-31 Receiver RX: 145.825 MHz AX.25 FMRX: 145.825 MHz AX.25 FM 216.98 MHz NSSS transponder216.98 MHz NSSS transponder  MARScom DD 1494 submitted. 148.375-148.975 MHz VHF cmd/user uplink148.375-148.975 MHz VHF cmd/user uplink 24-29 MHz Downlink24-29 MHz Downlink 300 MHz UHF YP Craft Uplink Whip300 MHz UHF YP Craft Uplink Whip  Resonate at 216.98 MHz

60. VHF EZNEC Plots

61. Radiation Hazard = None Deployed and Active 11 V/m Pre-Separation 0.11 V/m Antennas Compressed, Shorted, Shielded and Sep-SW OFF

62. RAFT1 Magnetic Attitude Control

63. 217Mhz Receiver

64. 217Mhz Receiver PCB 1.55in 2.175in

65. Mass Budget (kg) Light mass design for future missions Will ballast for RAFT

66. Shuttle Safety Requirements  Fracture Control Plan Captive & Redundant  Fastener integrity Captive & Redundant  Structural model of RAFTIdeas model, Buckling  Venting analysisDone. 0.04 “  Simple mechanismsAntennas  Materials / OutgassingCOTS, Replace  Conformal coat PC boardsYes  Wire sizing and fusing#24, fuse 1 amp  Radiation hazardBelow 0.1v/m  Battery safetyYes  Shock and vibrationYes

67. Battery Safety Requirements  Must have circuit interrupters in ground leg  Inner surface and terminals coated with insulating materials  Physically constrained from movement and allowed to vent  Absorbent materials used to fill void spaces  Battery storage temperature limits are -30°C to +50°C  Prevent short circuits and operate below MFR’s max  Thermal analysis under load and no-load  Battery must meet vibration and shock resistance stds  Must survive single failure without inducing hazards  Match cells for voltage, capacity, and charge retention

68.  Assumption: Launch NET February 2006 RAFT Kickoff Apr 04 RAFT Kickoff Apr 04 RAFT USNA SRR Sep 04 RAFT USNA SRR Sep 04 RAFT PDR19 Nov 04 RAFT PDR19 Nov 04 Launcher CDR Nov 04 Launcher CDR Nov 04  RAFT Phase 0/1 Safety16 Dec 04  RAFT CDR Feb 05  RAFT Phase 2 Safety Feb 05  RAFT Flight Unit Testing May 05  RAFT Phase 3 Safety Aug 05  RAFT Delivery/Install Oct 05  RAFT Flight (STS-116) 09 Feb 06 Key Milestones: Schedule