Presentation is loading. Please wait.

Presentation is loading. Please wait.

What’s needed to receive? A look at the minimum steps required for programming our 82573L nic to receive packets.

Similar presentations


Presentation on theme: "What’s needed to receive? A look at the minimum steps required for programming our 82573L nic to receive packets."— Presentation transcript:

1 What’s needed to receive? A look at the minimum steps required for programming our 82573L nic to receive packets

2 Accessing 82573L registers Device registers are hardware mapped to a range of addresses in physical memory We can get the location and extent of this memory-range from a BAR register in the 82573L device’s PCI Configuration Space We then request the Linux kernel to setup an I/O ‘remapping’ of this memory-range to ‘virtual’ addresses within kernel-space

3 kernel space Linux address-spaces dynamic ram nic registers user space kernel code/data nic registers ‘virtual’ address-spacephysical address-space 128-TB.text,.data,.bss stack shared libraries dynamic ram 64-GB

4 Kernel memory allocation The NIC requires that some host memory for packet-buffers and receive descriptors The kernel provides a ‘helper function’ for reserving a suitable region of memory in kernel-space which is both ‘non-pageable’ and ‘physically contiguous’ (i.e., kzalloc()) It’s our job is to decide how much memory our network controller hardware will need

5 Format for an Rx Descriptor Base-address (64-bits) status Packet- length Packet- checksum VLAN tag errors 16 bytes The device-driver initializes this ‘base-address’ field with the physical address of a packet-buffer The network controller will ‘write-back’ the values for these fields when it has transferred a received packet’s data into this descriptor’s packet-buffer

6 Suggested C syntax typedef struct{ unsigned long longbase_address; unsigned shortpacket_length; unsigned shortpacket_cksum; unsigned chardesc_status; unsigned chardesc_errors; unsigned shortvlan_tag; } RX_DESCRIPTOR; ‘Legacy Format’ for the Intel Pro1000 network controller’s Receive Descriptors

7 the packet’s data ‘payload’ goes here (usually varies from 56 to 1500 bytes) Ethernet packet layout Total size normally can vary from 64 bytes up to 1522 bytes (unless ‘jumbo’ packets and/or ‘undersized’ packets are enabled) The NIC expects a 14-byte packet ‘header’ and it appends a 4-byte CRC check-sum destination MAC address (6-bytes) source MAC address (6-bytes) Type/length (2-bytes) Cyclic Redundancy Checksum (4-bytes) 0 6 12 14

8 Rx-Descriptor Ring-Buffer Circular buffer (128-bytes minimum – and must be a multiple of 128 bytes) RDBA base-address RDLEN (in bytes) RDH (head) RDT (tail) = owned by hardware (nic) = owned by software (cpu) 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80

9 Packet-buffers and descriptors Our ‘nicrx.c’ module allocates 8 buffers of size 2K-bytes (i.e., more than enough for any normal Ethernet packets) 16K + 128 bytes allocated (8 packet-buffers, plus Rx-Descriptor Queue) for the Rx Descriptor Queue (128 bytes) for the eight packet-buffers

10 RxDesc Status-field PIFIPCSTCPCSVPIXSMEOPDD 7 6 5 4 3 2 1 0 DD = Descriptor Done (1=yes, 0=no) shows if nic is finished with descriptor EOP = End Of Packet (1=yes, 0=no) shows if this packet is logically last IXSM = Ignore Checksum Indications (1=yes, 0=no) VP = VLAN Packet match (1=yes, 0=no) USPCS = UDP Checksum calculated in packet (1=yes, 0=no) TCPCS = TCP Checksum calculated in packet (1=yes, 0=no) IPCS = IPv4 Checksum calculated on packet (1=yes, 0=no) PIF = Passed In exact Filter (1=yes, 0=no) shows if software must check UDPCS

11 RxDesc Error-field RXEIPETCPE reserved =0 SECE 7 6 5 4 3 2 1 0 RXE = Received-data Error (1=yes, 0=no) IPE = IPv4-checksum error TCPE = TCP/UDP checksum error (1=yes, 0=no) SEQ = Sequence error (1=yes, 0=no) SE = Symbol Error (1=yes, 0=no) CE = CRC Error or alignment error (1=yes, 0=no) SEQ reserved =0

12 Essential ‘receive’ registers enum{ E1000_CTRL0x0000,// Device Control E1000_STATUS0x0008,// Device Status E1000_RCRL0x0100,// Receive Control E1000_RDBAL0x2800,// Rx Descriptor Base Address Low E1000_RDBAH0x2804,// Rx Descriptor Base Address High E1000_RDLEN0x2808,// Rx Descriptor Length E1000_RDH0x2810,// Rx Descriptor Head E1000_RDT0X2818,// Rx Descriptor Tail E1000_RXDCTL0x2828,// Rx Descriptor Control E1000_RA0x5400,// Receive address-filter Array };

13 Programming steps 1)Detect the presence of the 82573L network controller (VENDOR_ID, DEVICE_ID) 2)Obtain the physical address-range where the nic’s device-registers are mapped 3)Ask the kernel to map this address range into the kernel’s virtual address-space 4)Copy the network controller’s MAC-address into a 6-byte array for future access 5)Allocate a block of kernel memory large enough for our descriptors and buffers 6)Insure that the network controller’s ‘Bus Master’ capability has been enabled 7)Select our desired configuration-options for the DEVICE CONTROL register 8)Perform a nic ‘reset’ operation (by toggling bit 26), then delay until reset completes 9)Select our desired configuration-options for the RECEIVE CONTROL register 10)Initialize our array of Receive Descriptors with the physical addresses of buffers 11)Initialize the Receive Engine’s registers (for Rx-Descriptor Queue and Control) 12)Give ‘ownership’ of all of our Rx-Descriptors to the network controller 13)Enable the Receive Engine 14)Install our ‘/proc/nicrx’ pseudo-file (for user-diagnostic purposes) NOTE: Steps 1) through 8) are the same as for our ‘nictx.c’ kernel module.

14 Device Control (0x0000) PHY RST VME R =0 TFCERFCE RST R =0 R =0 R =0 R =0 R =0 ADV D3 WUC R =0 D/UD status R =0 R =0 R =0 R =0 R =0 FRC DPLX FRC SPD R =0 SPEED R =0 SLUSLU R =0 R =0 R =1 0 FDFD 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 GIO M D R =0 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 FD = Full-DuplexSPEED (00=10Mbps, 01=100Mbps, 10=1000Mbps, 11=reserved) GIOMD = GIO Master DisableADVD3WUP = Advertise Cold Wake Up Capability SLU = Set Link UpD/UD = Dock/Undock statusRFCE = Rx Flow-Control Enable FRCSPD = Force SpeedRST = Device ResetTFCE = Tx Flow-Control Enable FRCDPLX = Force DuplexPHYRST = Phy ResetVME = VLAN Mode Enable 82573LWe used 0x04000A49 to initiate a ‘device reset’ operation

15 0 Device Status (0x0008) ?0 0 000 000000 GIO Master EN 000 0000 PHY RA ASDV ILOSILOS SLUSLU 0 TX OFF 0 FDFD 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Function ID LULU 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 SPEED FD = Full-Duplex LU = Link Up TXOFF = Transmission Paused SPEED (00=10Mbps,01=100Mbps, 10=1000Mbps, 11=reserved) ASDV = Auto-negotiation Speed Detection Value PHYRA = PHY Reset Asserted 82573L some undocumented functionality?

16 Receive Control (0x0100) R =0 00 FLXBUF SE CRC BSEX R =0 PMCF DPF R =0 CFI EN VFE BSIZE BAMBAM R =0 MODTYPRDMTS ILOSILOS SLUSLU LPEUPE 0 R =0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 SBP ENEN 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 LBMMPE EN = Receive Enable DTYP = Descriptor TypeDPF = Discard Pause Frames SBP = Store Bad Packets MO = Multicast OffsetPMCF = Pass MAC Control Frames UPE = Unicast Promiscuous Enable BAM = Broadcast Accept ModeBSEX = Buffer Size Extension MPE = Multicast Promiscuous Enable BSIZE = Receive Buffer SizeSECRC = Strip Ethernet CRC LPE = Long Packet reception Enable VFE = VLAN Filter EnableFLXBUF = Flexible Buffer size LBM = Loopback ModeCFIEN = Canonical Form Indicator Enable RDMTS = Rx-Descriptor Minimum Threshold SizeCFI = Canonical Form Indicator bit-value We used 0x1440821C in RCTL to prepare the ‘receive engine’ prior to enabling it

17 Rx-Descriptor Control (0x2828) 0000000 GRANGRAN 00 WTHRESH (Writeback Threshold) 000 FRC DPLX FRC SPD 0 HTHRESH (Host Threshold) ILOSILOS 0 ASDEASDE 0 LRSTLRST 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 00 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 PTHRESH (Prefetch Threshold) 00 Recommended for 82573: 0x01010000 (GRAN=1, WTHRESH=1) “This register controls the fetching and write back of receive descriptors. The three threshold values are used to determine when descriptors are read from, and written to, host memory. Their values can be in units of cache lines or of descriptors (each descriptor is 16 bytes), based on the value of the GRAN bit (0=cache lines, 1=descriptors). When GRAN = 1, all descriptors are written back (even if not requested).” --Intel manual

18 PCI Bus Master DMA 82573L i/o-memory RX and TX FIFOs (32-KB total) Host’s Dynamic Random Access Memory Descriptor Queue packet-buffer DMA on-chip RX descriptors on-chip TX descriptors

19 Pthresh and Hthresh When the number of unprocessed descriptors in the NIC’s on-chip memory has fallen below the Prefetch Threshold, and the number of valid descriptors in host memory which are owned by the NIC is at least equal to the Host Threshold, then the NIC will fetch that number of descriptors in a single ‘burst’ DMA-transfer

20 Wthresh When the number of descriptors waiting in the NIC’s on-chip memory to be written back to Host memory is at least equal to the Writeback Thrershold, then the NIC will write back that number of descriptors in a single ‘burst’ DMA-transfer

21 Experiment #1 Let’s install our ‘nicrx.c’ kernel module on one host, and use the ‘cat’ command to view its queue of Rx-Descriptors: $ /sbin/insmod nicrx.ko $ cat /proc/nicrx Then let’s install our ‘nictx.c’ module on a different host on the same local network: $ /sbin/insmod nictx.ko Now look again at the receive descriptors!

22 Experiment #2 Install our ‘dram.c’ device-driver module on both of these host-machines, and use our ‘fileview’ utility to look at the contents of each module’s packet-buffers – you’ll find their physical addresses displayed if you use ‘cat’ to see the descriptor-queues: $ cat /proc/nictxand$ cat /proc/nicrx

23 Experiment #3 Our ‘nicrx.c’ module had enabled both the Unicast and Multicast promiscuous modes So let’s watch what happens when we use the ‘/sbin/ifconfig’ command (with ‘sudo’) to bring up a secondary network interface on another host on the same segment of our local network Do you recognize these new packets?

24 Experiment #4 With ‘nicrx.c’ module installed on one host, log on to two other hosts on the same LAN and bring up their ‘eth1’ network interfaces Use the ‘ping’ command on one of these two hosts to try contacting the other one What do you observe about any packets that are received by the host where our ‘nicrx.c’ module had been installed?

25 In-class exercise Suppose you turn off the UPE-bit (bit #3) in the Receive Control register (in nicrx.c) From another host on the same segment, bring up its ‘eth1’ interface, then adjust its routing table so that all multicast packets are sent out via the secondary interface: $ sudo /sbin/route add –net 224.0.0.0 netmask 255.0.0.0 device eth1 If you ‘ping’ a multicast address, will the ICMP datagram be received by ‘nicrx.c’?


Download ppt "What’s needed to receive? A look at the minimum steps required for programming our 82573L nic to receive packets."

Similar presentations


Ads by Google