1. www.irrobot.com Marubot Football League Service Manual

2. www.irrobot.com 1 1. Power out The machine is designed to use AC and DC electricity together according to parts specifications. So, if the trouble seems on the power, consider the power source first and fix it as below. 1.1 Power Sources A) AC : Main Power, Fluorescent lightings, SMPS, Fans, and Air Blower B) DC : Other Parts 1.2 All lights out In this case, the most problems are on AC power. Check it as below. 1) Check the main power on the control panel. 2) Check the main power cable between inlet and outlet. 3) Check the fuse in the Inlet socket. 4) Check the light on the multi outlet. If the light is off, you need to replace the multi-outlet 1.3 Above Light s using AC power are on, but other parts are off. In this case, the most problems are on DC power and there may be conductors on the playground. If so, it make the short-circuit and fix it as below. Check the SMPS and if it does not work properly, replace it. If it works, remove conductors as below. 1) Turn off the power of the machine. 2) Open the Cover. 3) Clean the playground and remove the conductors. 4) Close the cover. 5) Turn on the power of the machine and test it (When you turn off and on, you have to wait 10-15 seconds for warming up.). ※ If you cannot fix the problem after above treats, call to your local dealer. Trouble Shooting

3. www.irrobot.com 1) Try to test with blow button on the control panel in side of the machine. 2) The ball is still not come out : If there is any foreign element, particle, or dust in the goal area or in the guide, the ball will not come out to the ground and it needs to remove them immediately. 3) How to remove particles : Use the vacuum cleaner to remove particles in the ground especially in the goal area and remove particles in the guide with hands after opening the door behind the machine. 2.The ball does not come out Once the ball goes in goal area, the ball move through the guide to the center pipe. And Air Blower will blow out the ball to the playing ground. The balls might be jammed at the entrance. Push the blow button on the control panel.

4. www.irrobot.com 3 3. The robot is not moving. A. One robot not moving Follow the bellows treat. 1)Check the robot power switch is “On” in the bottom of the robot. 2)When you turn on and off the switch, the expression LEDs on the robot face have to work properly. If not, you need to replace the robot power board. 3)Check the number of the power supplying pin under the robot. It must be six. 4)All of six have to have proper tension and tightly fixed. 5)If the power supplying pin is missing, broken, or worn out, replace the pin immediately. Also, it needs to check whether there is a missing or broken pin on the playground. Make sure to remove it, otherwise it will make short-circuit. 6)The robot’s LED is out within 10 minutes after putting the robot out from the playground, it may be discharged. Put the robot onto the playground and test it after 1~2 minutes. ※ If you cannot fix the problem after above treats, call to your local dealer. B. All robots not moving Follow the bellows treat. 1) Check the main power switch. 2) Turn off the main power and turn on in 15 seconds. 3) Check the robot power switch. 4) Check the short-circuit of the playground. ※ If you cannot fix the problem after above treats, check the main board and contact your local dealer.

5. www.irrobot.com 4 4. Disassembling the robot Front Side (3 Screws) Bottom (5 Screws) Wheel 4.1 Bolt / Snap Ring position (snap ring)

6. www.irrobot.com 5 4.2 Uncover the body Unscrew in 5 positions Unscrew in 2 positions on the ball guide

7. www.irrobot.com 6 Remove the snap rings with a snap-ring pliers or a pincette Pull out the wheels Uncover the body and magnetic. The result Snapring pliers a Pincette or

8. www.irrobot.com 7 4.3 Removing the battery Un-plug the battery cable Remove the battery The result

9. www.irrobot.com 8 4.4 Removing the Robot Main Board Un-plug the motor cables Move the cables from back to front Unscrew in 3 positions

10. www.irrobot.com 9 Un-plug 2 cables between main board and power board Unscrew in 3 positions on the power board Pull out the power board

11. www.irrobot.com 10 Complete disassembling

12. www.irrobot.com 11 4.5 Cautions Assembling procedures are in reverse way of decomposition. When you composite the body part and bottom part, be careful the position that is indicated in yellow round. When you look at the bottom part, there is rail and the body parts must be slide in the rail. If not, the robot case should be damaged. Rail