Presentation is loading. Please wait.

Presentation is loading. Please wait.

Advanced Engineering Design and Presentation C-Clamp Parametric Modeling Skill Builder Copyright © Texas Education Agency, 2014. All rights reserved.

Similar presentations


Presentation on theme: "Advanced Engineering Design and Presentation C-Clamp Parametric Modeling Skill Builder Copyright © Texas Education Agency, 2014. All rights reserved."— Presentation transcript:

1 Advanced Engineering Design and Presentation C-Clamp Parametric Modeling Skill Builder Copyright © Texas Education Agency, All rights reserved.

2 Creating a C-Clamp Create it to the specifications given. Change colors to match your school’s colors. Change “STEM” to your name or initials. Change “2014” to your graduation year. Copyright © Texas Education Agency, All rights reserved. 2

3 Layout Page 1 Copyright © Texas Education Agency, All rights reserved. 3

4 Layout Page 2 Copyright © Texas Education Agency, All rights reserved. 4

5 Layout Page 3 Copyright © Texas Education Agency, All rights reserved. 5

6 How to Create the Parts Create a folder on your drive for all of the C-Clamp parts and assemblies. Make sure you save to this folder only! The following slides will help you figure out how to create the parts. Part #1 – C-Clamp Base Part #2 – Protection Pad Part #3 – Shaft Screw Part #4 – Screw Swivel Part #5 – Tension Bar Copyright © Texas Education Agency, All rights reserved. 6

7 7 Part #1 - C-Clamp Base

8 Draw this and extrude it. Copyright © Texas Education Agency, All rights reserved. 8

9 Draw this and then extrude/cut it. Copyright © Texas Education Agency, All rights reserved. 9 Part #1 - C-Clamp Base

10 Add screw threads to the hole. Copyright © Texas Education Agency, All rights reserved. 10 Part #1 - C-Clamp Base

11 Copyright © Texas Education Agency, All rights reserved. 11 Draw this and then extrude/cut it. Part #1 - C-Clamp Base

12 Copyright © Texas Education Agency, All rights reserved. 12 Fillet the edges; mirror this using the YZ plane.

13 Part #1 - C-Clamp Base Create your initials or name. (Hint: Use the Text tool and then trace over the letters.) Copyright © Texas Education Agency, All rights reserved. 13

14 Part #1 - C-Clamp Base Repeat on the other side to add your graduation year. (Hint: Use the Text tool and then trace over the letters.) Copyright © Texas Education Agency, All rights reserved. 14

15 Copyright © Texas Education Agency, All rights reserved. 15 Part #2 - Protection Pad

16 Draw and then extrude this. Copyright © Texas Education Agency, All rights reserved. 16

17 Copyright © Texas Education Agency, All rights reserved. 17 Part #2 - Protection Pad Chamfer the four sides.

18 18 Copyright © Texas Education Agency, All rights reserved. Part #2 - Protection Pad Fillet the one bottom edge.

19 19 Copyright © Texas Education Agency, All rights reserved. Part #3 - Shaft Screw

20 Draw and extrude this. Copyright © Texas Education Agency, All rights reserved. 20

21 Copyright © Texas Education Agency, All rights reserved. 21 Part #3 - Shaft Screw Draw and extrude.

22 Copyright © Texas Education Agency, All rights reserved. 22 Part #3 - Shaft Screw Draw and extrude/cut this.

23 Add threads. Copyright © Texas Education Agency, All rights reserved. 23 Part #3 - Shaft Screw

24 Copyright © Texas Education Agency, All rights reserved. 24 Part #4 - Screw Swivel

25 Draw and extrude. Copyright © Texas Education Agency, All rights reserved. 25

26 Copyright © Texas Education Agency, All rights reserved. 26 Part #4 - Screw Swivel Draw and extrude.

27 Part #4 - Screw Swivel Copyright © Texas Education Agency, All rights reserved. 27 Add chamfer.

28 Part #4 - Screw Swivel Copyright © Texas Education Agency, All rights reserved. 28 Create hole through it.

29 29 Part #5 - Tension Bar Copyright © Texas Education Agency, All rights reserved.

30 Part #5 - Tension Bar Draw and extrude. Copyright © Texas Education Agency, All rights reserved. 30

31 Copyright © Texas Education Agency, All rights reserved. 31 Part #5 - Tension Bar Add fillet to both ends.

32 Place parts and constrain them to look like this. Copyright © Texas Education Agency, All rights reserved. 32 Assembly

33 Make an exploded view by tweaking, moving, and rotating to look like this. Copyright © Texas Education Agency, All rights reserved. 33 Make an Exploded View

34 Place the exploded and assembled views onto layout page #1; add the parts list and balloon annotations. Copyright © Texas Education Agency, All rights reserved. 34

35 Place the C-Clamp base and protection pad onto layout page #2; add annotations. Copyright © Texas Education Agency, All rights reserved. 35

36 Place the screw swivel, shaft screw, and tension bar onto layout page #3; add annotations. Copyright © Texas Education Agency, All rights reserved. 36

37 Follow the example and rubric given. Copyright © Texas Education Agency, All rights reserved. 37


Download ppt "Advanced Engineering Design and Presentation C-Clamp Parametric Modeling Skill Builder Copyright © Texas Education Agency, 2014. All rights reserved."

Similar presentations


Ads by Google