Download presentation

Presentation is loading. Please wait.

Published byBenedict Carson Modified over 2 years ago

2
Determine the waterline components needed to complete the water supply for the bathroom shown in figures 13-6 and 13-7

7
Starting with the hot water line: Approximately 10 feet of ½-inch pipe and 3 feet of ¾- inch pipe are needed. Beginning with the left side of the bathroom, the following fittings will be needed: One ¾” x ½” x ½” tee Three ½” tees Four ½” x 6” stub out fittings (one at each lavatory) One ½” 90-degree elbow (near the air chamber) One ½” x 12” air chamber

8
The cold water line servicing the lavatories will require the same components as the hot water line. The cold water line servicing the water closets and urinals will require: Approximately 20 feet of 1-inch pipe 7 feet of ¾-inch pipe. Three ½-inch risers are needed for the water closets (allow 18 inches each) Two ½-inch risers are needed for the urinals (allow 30 inches) for a total of 9.5 feet of ½- inch pipe.

9
Beginning in the lower left corner, the following fittings will be needed: One 1” x ¾” x 1” tee One 1” 90-degree elbow Two 1” x 1” x ½” tees One 1” x ¾” x ½” tee Two ¾” x ¾” x ½” tees One ¾” x ½” 90-degree elbow (near the air chamber) One ½” x 12” air chamber Five ½” x ½” 90-degree elbows (one per riser) Five ½” x 6” stub out fittings (one at each fixture).

13
Determine the DWV components needed to complete the DWV system for the bathroom shown in figures 13-8 and 13-9. The horizontal waste piping is 2 feet below the finished floor, the horizontal vent piping is 9 feet above the finished floor, and the vent terminates 14 feet above the finished floor.

16
The DWV piping will be taken off in three steps: the main(horizontal) waste, the vertical waste servicing the fixtures, and the vent. Beginning with the cleanout near the lavatories, the lengths of the pipe and fittings needed for the main waste line servicing the lavatories are as follows: 4 feet of 2-inch pipe run vertically, 5 feet of 2-inch pipe run horizontally, 15 feet of 3-inch pipe, one 2” cleanout plug, one 2” cleanout adapter, two 2” 90-degree elbows, one 2” sanitary tee, one 3” x 2” x 2” sanitary tee, two 3” x 3” x 2” sanitary tees, one 3” 45-degree sanitary elbow, one 3” x 4” busing and one 4” sanitary wye.

17
Beginning with the cleanout near the urinals, the lengths of pipe and fittings needed for the main waste line servicing the water closets and urinals are as follows: 4 feet of 2-inch pipe run vertically 5 feet of 2-inch pipe run horizontally 6 feet of 3-inch pipe 6 feet of 2-inch pipe (for the floor drain) 12 feet of 4-inch pipe one 2” cleanout plug one 2” cleanout adapter two 2” 90-degree elbows one 2” sanitary tee one 3” x 2” x 2” sanitary tee one 3” sanitary tee one 3” x 3” x 2” sanitary tee one 4” x 3” x 3” sanitary tee one 4” x 4” x 3” sanitary tee one 3” 45-degree sanitary elbow A floor drain is also needed.

18
Each of the lavatory risers will require: 4 feet of 2-inch pipe one 2” sanitary tee one 6 inch long piece of 2-inch pipe one male adapter The riser for each water closet requires: 1 foot of 3-inch pipe one 3” x 2” x 3” sanitary tee two feet of 3-inch pipe 3” 90-degree elbow servicing the water closet one 3” toilet flange. The riser for each urinal will require: * 5 feet of 2-inch pipe * one 2” sanitary tee * six inches of 2-inch pipe.

19
For the vertical venting pipe: Four 7-foot-long 2-inch pipes (lavatories) Two 8-foot-long 2-inch pipe (urinals) Four 10-foot-long 2-inch pipes (water closets and floor drain) will be needed. For the vertical vent pipe: Thirty-four feet of 2-inch pipe Six feet of 3” pipe ill be needed for the vertical vent stack through the roof. The following fittings are needed for the vent pipe: Four 2: 90-degree elbows Eight 2” tees One 3” tee Two 3” x 2” bushings. Additionally: Nine 2” test caps Four 3” test caps (water closets and roof vent) One 3” thermoplastic roof flashing Two decorative cleanout covers will be needed.

Similar presentations

OK

The idea evolved from two different contractor customers who shared with us a better way to perform hydrostatic testing of DWV piping system. Two different,

The idea evolved from two different contractor customers who shared with us a better way to perform hydrostatic testing of DWV piping system. Two different,

© 2018 SlidePlayer.com Inc.

All rights reserved.

Ads by Google

Ppt on power system protection Ppt on display advertising Ppt on our nation india Ppt on aerobics instructor Ppt on special types of chromosomes male Ppt on peak load pricing Ppt on disk formatting tools Ppt on power system harmonics thesis Ppt on transportation in plants and animals Ppt on meeting skills pdf