Presentation is loading. Please wait.

Presentation is loading. Please wait.

BELT DRIVE 1. A belt is a looped strip of flexible material, used to mechanically link two or more rotating shafts. 2. They may be used as a source of.

Similar presentations


Presentation on theme: "BELT DRIVE 1. A belt is a looped strip of flexible material, used to mechanically link two or more rotating shafts. 2. They may be used as a source of."— Presentation transcript:

1 BELT DRIVE 1. A belt is a looped strip of flexible material, used to mechanically link two or more rotating shafts. 2. They may be used as a source of motion, to efficiently transmit power, or to track relative movement. Belts are looped over pulleys. 3. In a two pulley system, the belt can either drive the pulleys in the same direction, or the belt may be crossed, so that the direction of the shafts is opposite.

2 Open belt drive

3 Cross belt drive.

4 Belts on a Yanmar 2GM20 marine diesel engine

5 FLAT BELT

6 VEE BELT

7 TIMING BELT

8 ROUND BELT

9 Advantages of belt drive They are simple. They are economical. They are simple. They are economical. Parallel shafts are not required. Parallel shafts are not required. Overload and jam protection are provided. Overload and jam protection are provided. Noise and vibration are damped out. Machinery life is prolonged because load fluctuations are cushioned (shock-absorbed). Noise and vibration are damped out. Machinery life is prolonged because load fluctuations are cushioned (shock-absorbed). They are lubrication-free. They require only low maintenance. They are lubrication-free. They require only low maintenance. They are highly efficient (90–98%, usually 95%). Some misalignment is tolerable. They are highly efficient (90–98%, usually 95%). Some misalignment is tolerable. They are very economical when shafts are separated by large distances. They are very economical when shafts are separated by large distances.

10 Disadvantages of belt drive The angular-velocity ratio is not necessarily constant or equal to the ratio of pulley diameters, because of belt slip and stretch. The angular-velocity ratio is not necessarily constant or equal to the ratio of pulley diameters, because of belt slip and stretch. Heat buildup occurs. Speed is limited to usually 7000 feet per minute (35 meters per second). Power transmission is limited to 370 kilowatts (500 horsepower). Heat buildup occurs. Speed is limited to usually 7000 feet per minute (35 meters per second). Power transmission is limited to 370 kilowatts (500 horsepower). Operating temperatures are usually restricted to –31 to 185°F (–35 to 85°C). Operating temperatures are usually restricted to –31 to 185°F (–35 to 85°C). Some adjustment of center distance or use of an idler pulley is necessary for wear and stretch compensation. Some adjustment of center distance or use of an idler pulley is necessary for wear and stretch compensation. A means of disassembly must be provided to install endless belts. A means of disassembly must be provided to install endless belts.

11 Chain drive Chain drive is a way of transmitting mechanical power from one place to another. Chain drive is a way of transmitting mechanical power from one place to another. It is often used to convey power to the wheels of a vehicle, particularly bicycles and motorcycles. It is often used to convey power to the wheels of a vehicle, particularly bicycles and motorcycles. It is also used in a wide variety of machines besides vehicles. It is also used in a wide variety of machines besides vehicles. Most often, the power is conveyed by a roller chain, known as the drive chain, passing over a sprocket gear, with the teeth of the gear meshing with the holes in the links of the chain. Most often, the power is conveyed by a roller chain, known as the drive chain, passing over a sprocket gear, with the teeth of the gear meshing with the holes in the links of the chain. The gear is turned, and this pulls the chain putting mechanical force into the system.. The gear is turned, and this pulls the chain putting mechanical force into the system..

12 Roller chain and sprocket

13 PROBLEM Following are the details of a crossed belt drive. Calculate the length of the belt? Diameter of the driver:200 mm Diameter of the follower:400 mm Center distance of the drive: 2m Speed of the driver:400 rpm Angle of contact: Determine the length of the belt. Solution: D1 = 200 mm D2= 400 mm C = 2m N1 = 400 rpm Length of the belt = L =2C+ П / 2 (D1+ D2) + (D1+ D2) / 4C = (2x2) + П / 2 ( ) + ( ) / 4x2 = 4.99 m

14 Possible Questions Short Answer Questions 1. Differentiate between open belt and crossed belt drive. 2. What are the commonly used materials for flat belts? 3. List out the applications of belt drives. 4. What do you mean by slip in a belt drive? 5. Differentiate between belt drive and chain drive. Long Answer Questions 1. Explain with neat sketch, the types of various flat belt drives. 2. List out the advantages and disadvantages of belt drives. 3. Compare flat belt and V belts. 4. Briefly explain chain drives.


Download ppt "BELT DRIVE 1. A belt is a looped strip of flexible material, used to mechanically link two or more rotating shafts. 2. They may be used as a source of."

Similar presentations


Ads by Google