Presentation is loading. Please wait.

Presentation is loading. Please wait.

LOGO 1. Objectives 2 Define the stages involved in project planning and construction 1 Conduct project analysis 2 Draw a rough sketch of your project.

Similar presentations


Presentation on theme: "LOGO 1. Objectives 2 Define the stages involved in project planning and construction 1 Conduct project analysis 2 Draw a rough sketch of your project."— Presentation transcript:

1 LOGO 1

2 Objectives 2 Define the stages involved in project planning and construction 1 Conduct project analysis 2 Draw a rough sketch of your project 3 Draw the block diagram for your project prototype. 4

3 LOGO Objectives 3 Prepare the orthographic drawing for the prototype using AutoCAD or any other software. 5 Prepare a Production Flowchart using Gantt Chart 6 Complete the Project Planning Report 7

4 LOGO Project Planning & Construction 4 project analysis project analysis Sketching System / Circuit diagram System / Circuit diagram orthographic drawing orthographic drawing production flowchart production flowchart Project Planning Report

5 LOGO Analysis 5 1. What is the project challenge? 2. Will the system control a sequence of operations? What are they? 2. Will the system control a sequence of operations? What are they? 3. Is it a closed loop system? 4. What inputs are required?

6 LOGO 6 5. What outputs are required? 6. What type of control does the system need? 6. What type of control does the system need? 7. What type of controller do you plan to use, and why? 7. What type of controller do you plan to use, and why? 8. Are there any other special considerations? 8. Are there any other special considerations?Analysis

7 LOGO Sketching 7 draw a rough sketch of your project prototype draw a rough sketch of your project prototype

8 LOGO System Diagram or Block Diagram 8

9 LOGO Exercise 1 9 Draw the block diagram for the water level control system by following the sequence of actions are listed below: Draw the block diagram for the water level control system by following the sequence of actions are listed below:

10 LOGO Exercise A switch (pressed by the visitor) will turn on the A switch (pressed by the visitor) will turn on the circuit. -The conductivity sensor will provide a feedback toThe conductivity sensor will provide a feedback to the 555 timer. -The timer will produce pulses with the requiredThe timer will produce pulses with the required time delay. -The pulses will turn the transistor driver ON andThe pulses will turn the transistor driver ON and OFF repeatedly with the set time delay. -The driver turns the relay ON and OFF, which inThe driver turns the relay ON and OFF, which in turn turns ON and off the pump. - A switch (pressed by the visitor) will turn on the A switch (pressed by the visitor) will turn on the circuit. -The conductivity sensor will provide a feedback toThe conductivity sensor will provide a feedback to the 555 timer. -The timer will produce pulses with the requiredThe timer will produce pulses with the required time delay. -The pulses will turn the transistor driver ON andThe pulses will turn the transistor driver ON and OFF repeatedly with the set time delay. -The driver turns the relay ON and OFF, which inThe driver turns the relay ON and OFF, which in turn turns ON and off the pump.

11 LOGO System Diagram or Block Diagram 11 Now, list the sequence of steps and draw the block diagram for your project prototype. Now, list the sequence of steps and draw the block diagram for your project prototype.

12 LOGO Circuit Diagram 12

13 LOGO Circuit Diagram 13

14 LOGO Circuit Diagram 14 Draw related circuit diagrams for your project prototype Draw related circuit diagrams for your project prototype

15 LOGO Orthographic Drawing 15 AutoCAD or any other software could be used to come up with a clear drawing of the intended prototype. Note : that the exact dimensions need to be marked clearly and all details of the design and materials must be included in the drawing. AutoCAD or any other software could be used to come up with a clear drawing of the intended prototype. Note : that the exact dimensions need to be marked clearly and all details of the design and materials must be included in the drawing.

16 LOGO Orthographic Drawing 16

17 LOGO Production Flowchart 17 A flowchart is a type of diagram that represents an algorithm or process, showing the steps as boxes of various kinds, and their order by connecting them with arrows.

18 LOGO Production Flowchart 18


Download ppt "LOGO 1. Objectives 2 Define the stages involved in project planning and construction 1 Conduct project analysis 2 Draw a rough sketch of your project."

Similar presentations


Ads by Google