Presentation is loading. Please wait.

Presentation is loading. Please wait.

L AB 2-4 A EIGRP F RAME R ELAY H UB AND S POKE : R OUTER U SED A S F RAME S WITCH Sang-Gon LEE Prof./Ph.D Division of Computer and Information Engineering,

Similar presentations


Presentation on theme: "L AB 2-4 A EIGRP F RAME R ELAY H UB AND S POKE : R OUTER U SED A S F RAME S WITCH Sang-Gon LEE Prof./Ph.D Division of Computer and Information Engineering,"— Presentation transcript:

1 L AB 2-4 A EIGRP F RAME R ELAY H UB AND S POKE : R OUTER U SED A S F RAME S WITCH Sang-Gon LEE Prof./Ph.D Division of Computer and Information Engineering, Dongseo University, Director of Innovation Center for Engineering Education(ICEE).

2 OBJECTIVES Review basic configuration of EIGRP on a serial interface Configure the bandwidth-percent command Configure EIGRP over Frame Relay hub and spoke Use EIGRP in non-broadcast mode Enable EIGRP manual summarization in topologies with discontiguous major networks

3 TOPOLOGY NOTE:- Given the diversity of router models and the differing naming conventions for serial interfaces (S0, S0/0, S0/0/0), The interface numbers on devices will probably differ from those in the topology diagram.

4 C ONTD.. Always draw network diagram to reflect topology. If any uncertainty for DCE connection, then use the show controllers serial interface_type interface_number command: HQ# show controllers serial0/0/0 Interface Serial0/0/0 Hardware is GT96K DCE V.35, clock rate

5 SCENARIO Suppose a company want to a new network between company Headquarter(HQ), East, and west branches. They are connected over hub and spoke Frame relay. company headquarter use as Hub. Each network with multiple loopback interfaces on each router. EIGRP to allow full connectivity between all departments. To simulate the Frame Relay WAN connections. Use a router with three serial ports configured as a frame switch.

6 STEP 1: ADDRESSING Apply IP addresses to the loopback interfaces on HQ, East, and West. Paste the following configurations into routers to begin must be in configuration mode when do this. HQ: ! interface Loopback1 ip address interface Loopback33 ip address interface Loopback65 ip address interface Loopback97 ip address interface Loopback129 ip address interface Loopback161 ip address ! end

7 C ONTD.. NOTE: all code is same just replace the only 1, In each address. (HQ=1, East=2, West=3). As Like: East:- ip address West:- ip address For now, the IP address is the only configuration on the serial interfaces. Leave the serial interfaces with their default encapsulation (HDLC)

8 C ONFIGURATIONS Recommendations are described in terms of configuring the interface "bandwidth" parameter EIGRP being able to use 50 percent of that bandwidth by default. Bandwidth configuration cannot be changed Bandwidth-percent command should be used to control the EIGRP bandwidth On low-speed interfaces, raising the available bandwidth for EIGRP above the default of 50 percent is advisable in order to improve convergence.

9 C ONTD.. LAN Interfaces (Ethernet, Token Ring, FDDI) set by default to the actual media speed bandwidth is explicitly configured to a very low value. Then need to configure. Point-to-Point Serial Interfaces (HDLC, PPP) defaults to T1 speed (1.544 Mbps) on serial interfaces set to the actual link speed. NBMA Interfaces (Frame Relay, X.25, ATM) particularly critical to configure nonbroadcast multi-access (NBMA) interfaces correctly. otherwise many EIGRP packets may be lost in the switched network.

10 C ONTD.. Three basic rules The traffic that EIGRP is allowed to send on a single virtual circuit (VC) cannot exceed the capacity of that VC. The total EIGRP traffic for all virtual circuits cannot exceed the access line speed of the interface. The bandwidth allowed for EIGRP on each virtual circuit must be the same in each direction Three different scenarios for NBMA interfaces Pure Multipoint Configuration (no subinterfaces) Pure Point-to-Point Configuration (each VC on a separate subinterface) Hybrid Configuration (point-to-point and multipoint subinterfaces

11 PURE MULTIPOINT CONFIGURATION (NO SUBINTERFACES) EIGRP will divide the configured bandwidth evenly across each virtual circuit. Must ensure that this will not overload each virtual circuit. For example: if you have a T1 access line with four 56K VCs, you should configure the bandwidth to be 224Kbps (4 * 56Kbps) in order to avoid dropping packets. If the total bandwidth of the virtual circuits equals or exceeds the access line speed, configure the bandwidth to equal the access line speed. Note that if the virtual circuits are of different capacities, the bandwidth must be set to take into account the lowest capacity virtual circuit. For instance, if a T1 access line has three 256Kbps VCs and one 56Kbps VC, the bandwidth should be set to 224Kbps (4 * 56Kbps). In such configurations, putting at least the slow virtual circuit onto a point-to-point subinterface is strongly recommended

12 PURE POINT-TO-POINT CONFIGURATION (EACH VC ON A SEPARATE SUBINTERFACE) configuration allows maximum bandwidth control, since the bandwidth can be configured separately on each subinterface virtual circuits have different capacities. It is best configuration. total bandwidth for all subinterfaces cannot exceed the available access line bandwidth If the interface is oversubscribed, the access line bandwidth must be divided across each of the subinterfaces For Example:- if a T1 access line (1544 Kbps) has ten virtual circuits with a capacity of 256Kbps, the bandwidth on each subinterface should be configured to be 154Kbps (1544/10) instead of 256Kbps each.

13 HYBRID CONFIGURATION (POINT-TO- POINT AND MULTIPOINT SUBINTERFACES) combinations of the two individual strategies Examples : Dotted Line :- corresponds to separate PVC Color: a separate IP subnet T o set the interface bandwidth to reflect the PVC capacity, Adjust the bandwidth prcentage for EIGRP. example, the desired bandwidth for EIGRP is (256K/10)*.9 = 23.04K; the bandwidth percentage would be 23.04K/56K =.41 (41%). So the same effect would be had by configuring: Interface Serial 0.1 point-to-point bandwidth 56 ip bandwidth-percent eigrp

14 C ONFIGURATION Hub Router interface Serial 0 encapsulation frame-relay !--- To enable Frame Relay encapsulation on the interface. interface Serial 0.1 point-to-point !--- The subinterface is configured to function as a point-to-point link using this command. bandwidth 25 !--- To set the bandwidth value for this interface. ip bandwidth-percent eigrp !--- To configure the percentage of bandwidth that may be !--- used by EIGRP on this interface. interface Serial 0.2 point-to-point bandwidth 25 ip bandwidth-percent eigrp Each of the ten spoke routers must be configured to limit EIGRP traffic to the same rate as that of the hub, in order to satisfy the third rule

15 C ONTD.. Spoke Router interface Serial 0 encapsulation frame-relay !--- To enable Frame Relay encapsulation on this interface. interface Serial 0.1 point-to-point !--- The subinterface is configured to function as a point-to-point link !--- using this command. bandwidth 25 !--- To set the bandwidth value for this interface. ip bandwidth-percent eigrp !--- To configure the percentage of bandwidth that may be !--- used by EIGRP on this interface.

16 FULL-MESH FRAME RELAY CONFIGURATION WITH DIFFERING ACCESS LINE SPEEDS A fully-meshed Frame Relay network of four routers running IPX EIGRP process ID 456, configured as a multipoint network

17 C ONTD.. Routers A-D interface Serial 0 encapsulation frame-relay !--- To enable Frame Relay encapsulation on this interface. bandwidth 56 !--- To set the bandwidth value for this interface

18 A POINT - TO - POINT SUBINTERFACE

19 C ONTD.. Configuration for A-C Router A-C interface Serial 0 encapsulation frame-relay !--- To enable Frame Relay encapsulation on this interface. interface Serial 0.1 multipoint !--- The subinterface is configured to function as a point-to-point link using this command. bandwidth 238 !--- To set the bandwidth value for this interface. interface Serial 0.2 point-to-point bandwidth 18 description PVC to Router D Router D's configuration Router D interface Serial 0 encapsulation frame-relay !--- To enable Frame Relay encapsulation on this interface. interface Serial 0.1 point-to-point bandwidth 18 !--- To set the bandwidth value for this interface.

20 CONTD… description PVC to Router A interface Serial 0.2 point-to-point !--- The subinterface is configured to function as a point-to-point link !--- using this command. bandwidth 18 description PVC to Router B interface Serial 0.3 point-to-point bandwidth 18 description PVC to Router C Router A-C interface Serial 0.1 multipoint !--- The subinterface is treated as a multipoint link. bandwidth 256 !--- To set the bandwidth value for this interface.

21 C ONTD.. ipx bandwidth-percent eigrp !--- To configure the percentage of bandwidth that may be used by !--- EIGRP on this interface. interface Serial 0.2 point-to-point !--- The subinterface is configured to function as a point-to-point link !--- using this command. bandwidth 56 description PVC to Router D ipx bandwidth-percent eigrp

22 STEP 2: CONFIGURING THE FRAME RELAY SWITCH Use 4 th Cisco router with 3 serial interfaces.(as a frame relay switch and cable the routers). Paste the following configuration into the router (depending on which equipment you have, the interface numbers may be different). ! hostname FRS ! frame-relay switching ! interface Serial0/0/0 description FR to HQ encapsulation frame-relay clock rate frame-relay lmi-type cisco frame-relay intf-type dce

23 C ONTD.. frame-relay route 102 interface Serial0/0/1 201 frame-relay route 103 interface Serial0/1/0 301 no shutdown ! interface Serial0/0/1 description FR to East no ip address encapsulation frame-relay clock rate frame-relay lmi-type cisco frame-relay intf-type dce frame-relay route 201 interface Serial0/0/0 102 no shutdown !

24 CONTD… interface Serial0/1/0 description FR to West no ip address encapsulation frame-relay clock rate frame-relay lmi-type cisco frame-relay intf-type dce frame-relay route 301 interface Serial0/0/0 103 no shutdown ! End

25 STEP 3: CONFIGURING THE FRAME RELAY ENDPOINTS Frame Relay(HQ), Spokes (East and West). Check the topology diagram for the data-link connection identifiers (DLCIs). Off Turn Frame Relay Inverse Address Resolution Protocol (InARP). Configure all Frame Relay interfaces as physical interfaces. Inverse ARP allows a Frame Relay network to discover the IP address associated with the virtual circuit A desirable trait in a production network. Turn Inverse ARP off to limit the number of dynamic DLCIs that are created.

26 CONTD… Its work in these pahses;- For a global configuration mode enter the configuration menu for that assign it an IP address with the help of ip address command. fourth octet of the IP address is the router number (HQ=1, East=2, West=3 Assign the Frame Relay subnet to be /29. Enable Frame Relay encapsulation using the interface configuration command encapsulation frame-relay. Disable Frame Relay Inverse ARP with the no frame- relay inverse-arp command.

27 CONTD…. Map the other IPs in the subnet to DLCIs, using the frame-relay map ip address dlci broadcast command HQ# conf t HQ(config)# interface serial 0/0/1 HQ(config-if)# ip address HQ(config-if)# encapsulation frame-relay HQ(config-if)# no frame-relay inverse-arp East# conf t East(config)# interface serial 0/0/1 East(config-if)# ip address East(config-if)# encapsulation frame-relay East(config-if)# no frame-relay inverse-arp

28 C ONTD.. East(config-if)# frame-relay map ip broadcast East(config-if)# frame-relay map ip broadcast East(config-if)# no shutdown West# conft West(config)# interface serial 0/0/0 West(config-if)# ip address West(config-if)# no frame-relay inverse-arp West(config-if)# encapsulation frame-relay West(config-if)# frame-relay map ip broadcast West(config-if)# frame-relay map ip broadcast West(config-if)# clock rate West(config-if)# no shutdown

29 C ONTD.. Each frame relay end points check the connectivity across the frame Relay network by the pinging the remote routers. For more information about this behavior of Frame Relay, see the following FAQ page:

30 STEP 4: SETTING INTERFACE-LEVEL BANDWIDTH Set the Frame Relay serial interface bandwidth with the interface-level command bandwidth bandwidth, specifying the bandwidth in kilobits per second. For HQ, use 128 kbps. On East and West, use 64 kbps by default, EIGRP limits its bandwidth usage to 50 percent of the value specified by the bandwidth parameter. Each neighbor for which this is an outbound interface has a traffic limit of a fraction of that 50 percent, represented by 1/N, where N is the number of neighbors out that interface HQ(config)# interface serial 0/0/1 HQ(config-if)# bandwidth 128 East(config)# interface serial 0/0/1 East(config-if)# bandwidth 64 West(config)# interface serial 0/0/0 West(config-if)# bandwidth 64

31 CONTD… How much bandwidth on Serial 0/0/1 on HQ is reserved for EIGRP traffic to East? On HQ, up to 32 Kbps of bandwidth can be utilized for EIGRP traffic to East. This represents one fourth of the total bandwidth of that interface Control both the bandwidth parameter and the EIGRP bandwidth percentage on a per-interface On HQ, limit the bandwidth used by EIGRP to 40 percent without changing the bandwidth parameter on the interface. The interface-level command ip bandwidth-percent eigrp as_number percent: HQ(config-if)# ip bandwidth-percent eigrp 1 40

32 STEP 5: CONFIGURING EIGRP Use the global configuration mode command router eigrp as_number Represented discontiguous network ( /8) configured on all routers. HQ sends and receives summaries for /8 from both East and West Auto summarization provokes considerable routing disruptions in the network and turn off auto-summarization on each router. two major networks using here are network for the loopbacks, and network for the Frame Relay cloud. Perform this configuration on all three routers HQ(config)# router eigrp 1 HQ(config-router)# network

33 C ONTD.. HQ(config-router)# network HQ(config-router)# no auto-summary Same for East and West Issue the show ip eigrp topology command on East: East# show ip eigrp topology IP-EIGRP Topology Table for AS(1)/ID( ) Codes: P - Passive, A - Active, U - Update, Q - Query, R - Reply, r - reply Status, s - sia Status P /19, 1 successors, FD is via Connected, Loopback1 P /19, 1 successors, FD is via ( /128256), Serial0/0/1 P /19, 1 successors, FD is via Connected, Loopback33 P /19, 1 successors, FD is via ( /128256), Serial0/0/1

34 CONTD… P /19, 1 successors, FD is via Connected, Loopback65 P /19, 1 successors, FD is via ( /128256), Serial0/0/1 P /19, 1 successors, FD is via Connected, Loopback97 P /19, 1 successors, FD is via ( /128256), Serial0/0/1 P /19, 1 successors, FD is via Connected, Loopback129 P /19, 1 successors, FD is via ( /128256), Serial0/0/1 P /19, 1 successors, FD is via Connected, Loopback161

35 C ONTD.. P /19, 1 successors, FD is via ( /128256), Serial0/0/1 P /29, 1 successors, FD is via Connected, Serial0/0/1 East# Which networks are missing from the topology database? All of the subnets in the /16 range are missing from East’s topology table. These are the remote loopback interfaces on the West router. What do you suspect as being responsible for this problem? This problem is caused by the split horizon functionality on R1. R1 will not send route updates from East to West because the incoming interface and outgoing interface are the same.

36 C ONTD.. Router 1 needs the no ip split-horizon eigrp as_number command on its serial Frame Relay interface This command disables split horizon for an EIGRP autonomous system If split horizon is enabled (the default), route advertisements from East to HQ do not travel to West and vice versa, Example : HQ(config)# interface serial 0/0/1 HQ(config-if)# no ip split-horizon eigrp 1

37 C ONTD.. Verify the correct EIGRP adjacencies with the show ip eigrp neighbors command: HQ# show ip eigrp neighbors IP-EIGRP neighbors for process 1 H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num Se0/0/ :00: Se0/0/ :00: East# show ip eigrp neighbors IP-EIGRP neighbors for process 1 H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num Se0/0/ :00: West# show ip eigrp neighbors IP-EIGRP neighbors for process 1 H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num Se0/0/ :00:

38 IP ROUTE C OMMAND show ip route command through Verify IP routes:- Example:- HQ# show ip route /29 is subnetted, 1 subnets C is directly connected, Serial0/0/ /19 is subnetted, 18 subnets D [90/ ] via , 00:04:36, Serial0/0/1 D [90/ ] via , 00:04:20, Serial0/0/1 C is directly connected, Loopback1 D [90/ ] via , 00:04:36, Serial0/0/1 D [90/ ] via , 00:04:20, Serial0/0/1 C is directly connected, Loopback33 D [90/ ] via , 00:04:37, Serial0/0/1 D [90/ ] via , 00:04:21, Serial0/0/1

39 C ONTD.. C is directly connected, Loopback65 D [90/ ] via , 00:04:37, Serial0/0/1 D [90/ ] via , 00:04:21, Serial0/0/1 C is directly connected, Loopback97 D [90/ ] via , 00:04:37, Serial0/0/1 D [90/ ] via , 00:04:21, Serial0/0/1 C is directly connected, Loopback129 D [90/ ] via , 00:04:37, Serial0/0/1 D [90/ ] via , 00:04:21, Serial0/0/1 C is directly connected, Loopback161 Same as another Two (EAST and WEST) ip route.

40 TCL S CRIPTS Run the following TCL script on all routers to verify full connectivity: for each address { (… continue)

41 C ONTD } { ping $address } If anybody never used TCL scripts or need a refresher, see the TCL lab in the routing module.

42 STEP 6: USING NON-BROADCAST EIGRP MODE EIGRP use as default mode, which multicasts packets to the link-local address All Frame relay not support mulitcast. EIGRP supports unicasts to remote destinations using non broadcast mode on a per-interface basis mode is analogous to configuring RIPv2 with a passive interface and statically configuring neighbors out that interface To implement this functionality, do the following: HQ(config)# router eigrp 1 HQ(config-router)# neighbor serial 0/0/1 HQ(config-router)# neighbor serial 0/0/1 East(config)# router eigrp 1 East(config-router)# neighbor serial 0/0/1 West(config)# router eigrp 1 West(config-router)# neighbor serial 0/0/0

43 CONTD… HQ now has two neighbor statements, and the other two routers have one. Once you configure neighbor statements for a given interface, EIGRP automatically stops multicasting packets out that interface and starts unicasting packets instead. verify that all your changes have worked with the show ip eigrp neighbors command: HQ# show ip eigrp neighbors IP-EIGRP neighbors for process 1 H Address Interface Hold UptimeSRTT RTO Q Seq (sec) (ms) Cnt Num Se0/0/ :00: Se0/0/ :00:

44 I P EIGRP NEIGHBOURS East# show ip eigrp neighbors IP-EIGRP neighbors for process 1 H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num Se0/0/ :02: West# show ip eigrp neighbors IP-EIGRP neighbors for process 1 H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num Se0/0/ :03:

45 STEP 7: IMPLEMENTING EIGRP MANUAL SUMMARIZATION Implement EIGRP manual summarization on each of the routers. Each router should advertise only one network summarization. What is the length of the network mask that is used to summarize all the loopbacks on each router? Summarize all the loopbacks at the 24-bit boundary for each router. Simplified EIGRP topology table on each router using the show ip eigrp topology command: HQ# show ip eigrp topology IP-EIGRP Topology Table for AS(1)/ID( ) Codes: P - Passive, A - Active, U - Update, Q - Query, R – Reply, r - reply Status, s - sia Status P /16, 1 successors, FD is via ( /128256), Serial0/0/1 P /16, 1 successors, FD is

46 CONTD… via ( /128256), Serial0/0/1 P /16, 1 successors, FD is via Summary (128256/0), Null0 P /19, 1 successors, FD is East# show ip eigrp topology IP-EIGRP Topology Table for AS(1)/ID( ) Codes: P - Passive, A - Active, U - Update, Q - Query, R – Reply, r - reply Status, s - sia Status P /16, 1 successors, FD is via Summary (128256/0), Null0 P /19, 1 successors, FD is via Connected, Loopback1 P /16, 1 successors, FD is via ( / ), Serial0/0/1 P /16, 1 successors, FD is via ( /128256), Serial0/0/1

47 W EST SHOW IP EIGRP TOPOLOGY IP-EIGRP Topology Table for AS(1)/ID( ) Codes: P - Passive, A - Active, U - Update, Q - Query, R – Reply, r - reply Status, s - sia Status P /16, 1 successors, FD is via ( / ), Serial0/0/0 P /16, 1 successors, FD is via Summary (128256/0), Null0 P /19, 1 successors, FD is via Connected, Loopback1 P /16, 1 successors, FD is via ( /128256), Serial0/0/0 P /19, 1 successors, FD is

48 APPENDIX A: TCL SCRIPT OUTPUT HQ# tclsh HQ(tcl)#foreach address { +>(tcl)# >(tcl)# >(tcl)# >(tcl)# >(tcl)# >(tcl)# >(tcl)# >(tcl)# >(tcl)# >(tcl)# >(tcl)# >(tcl)# >(tcl)# >(tcl)# >(tcl)# >(tcl)# >(tcl)#

49 C ONTD.. +>(tcl)# >(tcl)# >(tcl)# >(tcl)# >(tcl)#} { ping $address } Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to , timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to , timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/4 ms Type escape sequence to abort. …………………. ……….. …. Success rate is 100 percent (5/5), round-trip min/avg/max = 40/42/44 ms HQ(tcl)# tclquit

50 E AST TCL CODE East# tclsh East(tcl)#foreach address { +>(tcl)# >(tcl)# >(tcl)# >(tcl)# >(tcl)# >(tcl)# >(tcl)# >(tcl)# >(tcl)# >(tcl)# >(tcl)# >(tcl)# >(tcl)# >(tcl)#

51 C ONTD.. +>( tcl)# >(tcl)# >(tcl)# >(tcl)# >(tcl)# >(tcl)# >(tcl)# >(tcl)#} { ping $address } Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to , timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 40/42/44 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to , timeout is 2 seconds: !!!!! …………………………. Success rate is 100 percent (5/5), round-trip min/avg/max = 84/84/88 ms East(tcl)# tclquit

52 CONTD… West# tclsh West(tcl)#foreach address { +>(tcl)# >(tcl)# >(tcl)# >(tcl)# >(tcl)# >(tcl)# >(tcl)# >(tcl)# >(tcl)# >(tcl)# >(tcl)# >(tcl)# >(tcl)# >(tcl)# >(tcl)#

53 +>(tcl)# >(tcl)# >(tcl)# >(tcl)# >(tcl)# >(tcl)# >(tcl)#} { ping $address } Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to , timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 40/42/44 ms Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to , timeout is 2 seconds: !!!!! …………………. …………. Success rate is 100 percent (5/5), round-trip min/avg/max = 84/84/84 ms West(tcl)# tclquit CONTD…

54 END OF LAB CONFIGS: HQ#show run Building configuration... ! hostname HQ ! interface Loopback1 ip address ! interface Loopback33 ip address ! interface Loopback65 ip address ! interface Loopback97 ip address ! interface Loopback129 ip address !

55 C ONTD.. interface Loopback161 ip address ! interface Serial0/0/1 ip address encapsulation frame-relay no ip split-horizon eigrp 1 ip summary-address eigrp frame-relay map ip frame-relay map ip broadcast frame-relay map ip broadcast no frame-relay inverse-arp no shutdown ! router eigrp 1 network network no auto-summary neighbor Serial0/0/1 neighbor Serial0/0/1 ! end

56 E AST SHOW RUN East#show run Building configuration... ! hostname East ! interface Loopback1 ip address ! interface Loopback33 ip address ! interface Loopback65 ip address ! interface Loopback97 ip address ! interface Loopback129 ip address ! interface Loopback161 ip address !

57 C ONTD.. interface Serial0/0/1 ip address encapsulation frame-relay ip summary-address eigrp frame-relay map ip broadcast frame-relay map ip frame-relay map ip broadcast no frame-relay inverse-arp no shutdown ! router eigrp 1 network network no auto-summary neighbor Serial0/0/1 ! end

58 W EST SHOW R UN West#show run Building configuration... ! hostname West ! interface Loopback1 ip address ! interface Loopback33 ip address ! interface Loopback65 ip address ! interface Loopback97 ip address ! interface Loopback129 ip address ! interface Loopback161 ip address !

59 C ONTD.. interface Serial0/0/0 ip address encapsulation frame-relay ip summary-address eigrp frame-relay map ip broadcast frame-relay map ip broadcast frame-relay map ip no frame-relay inverse-arp frame-relay lmi-type cisco no shutdown ! router eigrp 1 network network no auto-summary neighbor Serial0/0/0 ! end

60 Thank You


Download ppt "L AB 2-4 A EIGRP F RAME R ELAY H UB AND S POKE : R OUTER U SED A S F RAME S WITCH Sang-Gon LEE Prof./Ph.D Division of Computer and Information Engineering,"

Similar presentations


Ads by Google