Presentation is loading. Please wait.

Presentation is loading. Please wait.

ECE 1201 Engineering Lab II. Taaruf Nor Farahidah Za’bah Room number : E2-2-13.12 Phone number : 03-61964562 address :

Similar presentations


Presentation on theme: "ECE 1201 Engineering Lab II. Taaruf Nor Farahidah Za’bah Room number : E2-2-13.12 Phone number : 03-61964562 address :"— Presentation transcript:

1 ECE 1201 Engineering Lab II

2 Taaruf Nor Farahidah Za’bah Room number : E Phone number : address : The lab technicians are – Br. Shahbudin Basri and Br. Rosley Mahadi Course website:

3

4

5 Tentative WeekExperiment No. (Title) 1Introductory class – Briefing on the organization of the course 2Introduction to PSPICE 3PSPICE 4 Experiment No. 1 & 2 (Diode Characteristics & Zener Diode Characteristics) 5 & 6 Experiment No. 3 (Wave Rectifier & Clipper Circuit) 7 & 8 Experiment No. 4 (BJT Characteristics & Common-Emitter Transistor Amplifier) 9 & 10 Experiment No. 5 (BJT Biasing Circuits) 11 Experiment No. 6 (MOSFET - Common Source Amplifier) 12 Experiment no. 7 (Inverting and Non-Inverting OP Amp)

6 Quiz20 % Final Test35 % Lab Report45 % Assessment

7 Safety Please wear covered shoes – NO SLIPPER. Otherwise, you will be asked to leave the lab. Power must be switched off whenever an experiment or project is being assembled, disassembled, or modified.

8 Tidiness When the experiment has been satisfactory completed and the results approved by the instructor, the students may disconnect the circuit and return the components and instruments to the locker tidily. Chairs are to be slid in properly. DO NOT WRITE anything on the table

9 Preparation Read the entire experiment and research any required theory beforehand. Many times an experiment takes longer that one class period simply because a student is not well prepared. The experiment is performed in pairs (max=3 students per group) but the final exam is performed individually – One group = one lab report

10 Lab Reports Reports have to be handwritten for submission. – Writing should appear on one side of each sheet only. – The students’ name & matric number, section number, lab session and the lecturer’s – Please indicate the author of each section in your report. The cover page of the lab report can be downloaded from the website.

11

12 Report Format and Evaluation No.Evaluation Items% Marks 1Objectives2 2Experiment Set-up4 3Results & Observation4 4PSPICE4 5Discussion and Conclusion 6 TOTAL20

13 Tentative WeekExperiment No. (Title) 1Introductory class – Briefing on the organization of the course 2Introduction to PSPICE – Tutorial 1 3PSPICE - Tutorial 2 Preparation for PSPICE Tutorial

14 Download 16.6_OrCAD_Lite_Capture&PSpice_Products.zip from the any computer in the lab – It is a zipped file, you have to extract the files into a designated folder – Once you have extracted, go to Disk 1 and look for SETUP (it is an application file) to install the software. – One group will require ONE laptop for the tutorial sessions

15 Introduction to Lab Equipment Bread board and its connections

16

17 Function Generator – To create AC signals such as Sine-Wave, Triangular Waves etc – The user can alter its frequency and amplitude Example of a function generator

18 Oscilloscope – An equipment to show the obtained result. – Has 2 channels One for input signal One for output signal

19 DC power supply – To provide DC supply to your circuit which you can measure using digital multimeter


Download ppt "ECE 1201 Engineering Lab II. Taaruf Nor Farahidah Za’bah Room number : E2-2-13.12 Phone number : 03-61964562 address :"

Similar presentations


Ads by Google