Presentation is loading. Please wait.

Presentation is loading. Please wait.

Elvin Harms, Tom Peterson, Yuriy Orlov, Frank McConoloque.

Similar presentations


Presentation on theme: "Elvin Harms, Tom Peterson, Yuriy Orlov, Frank McConoloque."— Presentation transcript:

1 Elvin Harms, Tom Peterson, Yuriy Orlov, Frank McConoloque

2 2 -Existing CC1 Vacuum vessel: 800mm-OD, 1800mm-long -Cold mass G10 Support Rods location 1 -80K (N 2 )-return 2 -80K (N 2 )-supply K (He)-cooldwn K (He)-supply K (He)-supply K (He)- return -MC Port with New MC -Cold mass Fixing point in “Z” Top port with Cryo piping BEAM Y. Orlov09/05/2012

3 -Vacuum vessel -80K shield -5K intercept (x2) -Gate valve with supports (x2) -1.3 GHz cavity RI29 -Cold mass fixing G10 post in “Z” direction 3 Y. Orlov09/05/2012

4 -MC Warm -MC Cold -G10 Support Rods (x8) CM support Frame 4 Y. Orlov09/05/2012

5 -Existing GV access Ports USDS 5 G10 Support Rods MC Warm with supports Y. Orlov09/05/2012

6 Serial #: TB9RI MV/m -MC cold -Blade tuner (install after CR assembly) -Ti He vessel with 2-phase He pipe -9 cell cavity -External magnetic shield (install after CL Assy 6 Y. Orlov09/05/2012

7 -Cavity without Blade Tuner Under vacuum (?) -Gate Valve (x2) US DS 7 -Bellows between Cavity flange and GV -DS BP bellows connect to Vacuum Vessel (bellows restrains not shown) -US BP bellows connect to Vacuum Vessel (bellows restrain not shown) Y. Orlov09/05/2012

8 US DS -5K He Piping line -5K Intercept MC -Warm Up Cool down Line -5K Intercept to Space Frame -5K Intercept to Beam Pipe by Cu Bar (x2) -1.4 K He Supply line -US GV Support -80K intercept -Combined block for needle Bearings and G10 rods supports (x4) 8 Y. Orlov09/05/2012

9 -Pumping Line with He Level Indicator -1.3 GHz Cavity End Magnetic shields -Tuner motor thermal intercept -Auminum Space Frame -DS HOM connector intercept DS US -DS GV Support with needle bearings -US HOM connector intercept -US GV Support with needle bearings 9 Y. Orlov09/05/2012

10 10 GV 5K 80K-80K Intercept -5K intercept -G10 Vibration compensator (2 parts) Y. Orlov09/05/2012

11 - Weldable Al 6061 space frame (needle support places are machined after welding) -4 Needle supports combined with G10 rods support -US Gate Valve Support 11 Y. Orlov09/05/2012

12 Y. Orlov mm Plungers with spring washers (compensate thermal shrinkage) “ Hard” screw connection Installation Gap ~4mm

13  Total DRAWINGS: ~91 -New drawings: 61+8(not released + released) -ILC drawings: 22 (Assembly DWG’s + parts DWG’s)  Ordered subassemblies: 3 (DWG##, MD , MD , MC ) + existing ILC parts (were ordered for CM3-CM6) 09/05/2012Y. Orlov 13


Download ppt "Elvin Harms, Tom Peterson, Yuriy Orlov, Frank McConoloque."

Similar presentations


Ads by Google