We think you have liked this presentation. If you wish to download it, please recommend it to your friends in any social system. Share buttons are a little bit lower. Thank you!
Presentation is loading. Please wait.
Published byAaron Twyman
Modified about 1 year ago
1 V1.00 © 2009 ZelFlex QR Quick Released double-sided mechanical stretching frame Step by step User guide
2 Assembly of protect frame Frame without stencil ZelFlex QR V1.00 © 2009
3 Assembly of protect frame Using the two hexagon- headed screws, attach the rear bar according to the stencil length. Tighten them. Rear bar must be parallel to the rear frame profile. ZelFlex QR V1.00 © 2009
4 Assembly of protect frame Unwind the nuts from the stretching screws by about 10 mm. ZelFlex QR V1.00 © 2009
5 Assembly of protect frame Remove the holding bars from the rear clamping and front stretching bars. ZelFlex QR V1.00 © 2009
6 Remove the holding bars in 3 steps : Step 1 – Press the holding bar down Step 2 - Move the holding bar to the right direction Step 3 – Remove the holding bar ZelFlex QR V1.00 © 2009
7 Assembly of protect frame Remove holdings bars and place them in front of and behind the frame. ZelFlex QR V1.00 © 2009
8 Place the stencil to the pins on the rear clamping bar. ZelFlex QR V1.00 © 2009
9 Assembly of protect frame Close the rear clamping bar with the rear holding bar. ZelFlex QR V1.00 © 2009
10 Close the rear holding bar in 3 steps : Step 1 – Place the holding bar to the rear clamping bar Step 2 - Press down the holding bar and move it to the left. Step 3 - Release the holding bar. ZelFlex QR V1.00 © 2009
11 Place the stencil to the pins on the front stretching bar. ZelFlex QR V1.00 © 2009
12 Assembly of protect frame Close the front stretching bar with the front holding bar. ZelFlex QR V1.00 © 2009
13 Close the front stretching bar in 3 steps : Step 1 – Place the holding bar to the front stretching bar Step 2 - Press down the holding bar and move it to the left. Step 3 - Release the holding bar. ZelFlex QR V1.00 © 2009
14 Assembly of protect frame Tighten the stretching screw to get correct tension of the stencil. ZelFlex QR V1.00 © 2009
15 Assembly of protect frame Gap between locker on stretching screw and bar should be approx. 3 mm for required working tension. ZelFlex QR V1.00 © 2009
16 Assembly of protect frame Frame with stretched stencil from bottom side. ZelFlex QR V1.00 © 2009
17 Assembly of protect frame Your ZelFlex QR frame is ready to use! ZelFlex QR V1.00 © 2009
18 ZelFlex QR V1.00 © 2009
19 © 2009 Thank you for your attention. LPKF Laser & Elektronika d.o.o. · Polica 33 · 4202 Naklo · Slovenia ·
How To Install RAM In Laptop Installing Larger RAM is the easiest way speed up your laptop computer. This Post will guide you about installing laptop computers.
Instructions for making plunger fork tool. Drawing for the trigger assembly.
Boarding the BUS SPE 518 Amy Marino. Boarding the Bus Walk to the School Bus.
Sectional Assembly and Installation. Sectional Assembly & Installation Items Needed for Installation 1)6D Galvanized Screws 2)Silicone 3)1 ½ x 1 ½ x 3.
How to center the top roller Current Situation The slider is not centered because the bottom slider was not placed at 6 o’clock ?!
Checking your bike Checking your bike is quick and easy to do (you dont need to be a cycle mechanic). With practice it should only take a few minutes if.
Co-ordinates & Translations. The objective of this lesson is: To plot a shape and translate it for a given rule. To work out the translation from its.
Leisure Vac Auto pool Cleaner. Trouble shooting Guide: Top Head Assembly Problem: Debris in the top head, causing cleaner to not work due to poor water.
IN ON UNDER IN FRONT OF BEHIND BETWEEN NEXT TO NEAR ON THE LEFT OF ON THE RIGHT OF.
D.T. unit 5C: Moving Toys How to make a moving toy.
How to Build a Wagon by Michael White One day you are at the store, and you see a nice wagon on the shelf. You just had to have it. So you buy the.
Corner of building marked on kerb Determining the Building Line A building square is positioned against the rear of the kerb, beyond the corner mark indicated.
Keyboard Techniques. Left and Right Hand Keys Left Hand KeysRight Hand Keys.
To understand the role played by tie rods, it is necessary to appreciate what is happening inside the cylinder of the engine. When the piston is just after.
STATIC STRETCHES Stretch to the point of resistance. Hold each stretch for 10 – 15 seconds. Do not bounce.
VentStop V.C.U Step 6. Lower down all 4 sides, make sure they are as flat as possible and there are no large rocks underneath. Check orientation. Step.
Welcome to Welcome to. The DTS Garage door openers are imported by DTS Security Products CC. We continue to upgrade our products via our suppliers to.
Textiles – Jazzy Hat Project Name - Year Group - Homework Booklet.
Helmet Light User Instructions Rotate Tail cap counter clock wise to open battery compartment IR / IFF lever (only functional light In this mode) Two functional.
UnFramed Canopy Fitting Instructions V3.0 Contents – 1 x handle pack 12 x 30mm Wood Screws 4 x M8 flat washers 3 keys 1x door 4 x M8 - 50mm coach screws.
Want to see the inside of my House? Follow me, for a guided tour You MUST have PowerPoint viewer to see this presentation Click your mouse to advance the.
Step 1 : Loop one end of the pipe cleaner to form a U-shape as shown in the diagram about 4 cm.
By: Lindsay Myers. Gather wood (cherry, walnut, maple) Plane wood (walnut – 1/8 in, all else – ¾ in) Joint one side of each board Cut boards to width.
BMW 1985 – 325e Timing Belt and Water Pump Replacement Start to Finish Take Your Time, Its Not as Bad as It Seems! I was VERY apprehensive about doing.
Co-ordinates & Rotations 2. The objective of this lesson is: To work out the centre of rotation and the angle of rotation of a shape from its original.
Tagger and Vacuum Chamber Assembly Procedure. Outline. Assembly procedure for tagger and vacuum chamber. Support stands. Alignment.
Tessellation. Tessellation If many copies of a shape can be used to cover a surface, without leaving.
BeginningNext SlideBack End Program AVADAL 1 of 21 SK-1 Roller Apron Segment Overview.
Mouse Training Instruction by: Connie Hutchison & Christopher McCoy.
How To Catch A Swarm Using Buckets. Take 2 plastic buckets and cut a large matching hole in the bottom of each. Using screen wire, preferably 1/8 hardware.
© 2016 SlidePlayer.com Inc. All rights reserved.