Presentation is loading. Please wait.

Presentation is loading. Please wait.

Stable Rise –Pull and Swivel Top Installation and Set Up Guide Jaymil Ergo & Office Solutions 150 Dow Street, Tower 4, Manchester, NH 603.629.9995.

Similar presentations


Presentation on theme: "Stable Rise –Pull and Swivel Top Installation and Set Up Guide Jaymil Ergo & Office Solutions 150 Dow Street, Tower 4, Manchester, NH 603.629.9995."— Presentation transcript:

1 Stable Rise –Pull and Swivel Top Installation and Set Up Guide Jaymil Ergo & Office Solutions 150 Dow Street, Tower 4, Manchester, NH

2 Tools Required Jaymil Ergo & Office Solutions 150 Dow Street, Tower 4, Manchester, NH Drill ½” Drill Bit Philips or Flat Head Bit (to be confirmed) Level Measuring Tape Allen Wrench #5

3 Assemble Column Jaymil Ergo & Office Solutions 150 Dow Street, Tower 4, Manchester, NH Lay column down with cord facing up. Install bracket around the column with the Wall Mount Bracket facing up. Install top bracket approximately 4” down from top. Use an #5 Allen Wrench to tighten screws into bracket. Install base bracket at bottom with 6 screws Wall Mount Bracket Cord

4 Assemble Column – With Optional Column Extender Jaymil Ergo & Office Solutions 150 Dow Street, Tower 4, Manchester, NH Remove panel from Column Extender Screw Column Extender to base of Column with opening facing back (same direction as cord) Replace panel of Column Extender. Cord

5 Assemble Column – With Optional Column Extender Jaymil Ergo & Office Solutions 150 Dow Street, Tower 4, Manchester, NH Lay column down with cord facing up. Install brackets around the column with the Wall Mount Bracket facing up. Install top bracket approximately 4” down from top. Install bottom bracket over the seam of the column and column extender. Use an #5 Allen Wrench to tighten screws into brackets. Wall Mount Bracket Cord

6 Install Brackets– Pull and Swivel Jaymil Ergo & Office Solutions 150 Dow Street, Tower 4, Manchester, NH Before mounting column to wall follow the below instructions. Mount pull and Swivel head with 4 screws. NOTE: Column Cord can be facing the front or back. The Column Cord does NOT go through a hole in the Pull and Swivel Head. Cord should be sandwiched pointing down by the Pull and Swivel Head (if cord is at the front of column) or Power Supply Bracket (if cord is at the back of column). Insert drawing images

7 Install Brackets– Pull and Swivel Jaymil Ergo & Office Solutions 150 Dow Street, Tower 4, Manchester, NH Mount Control and Power Supply Brackets with supplied screws to column per drawing. Screw Control to Control Bracket. Power Supply will mount with Power Supply Bracket or Velcro to back side of Column. Insert drawing images

8 Mount to Wall– Pull and Swivel Jaymil Ergo & Office Solutions 150 Dow Street, Tower 4, Manchester, NH Now that the brackets are installed to the column, mount to the wall.

9 Mount Column to Wall Jaymil Ergo & Office Solutions 150 Dow Street, Tower 4, Manchester, NH Select position on wall. Column will need access to a power outlet. Position Column on wall, level and mark holes. Check for studs in wall. Move column aside and drill pilot holes in the drywall to test for studs. Avoid studs if possible. If you hit a wood stud: use wood screws into the wood studs instead of anchors. Use Toggler Snaptoggle Anchor in other points. If you hit a metal stud: drill out metal stud and use Toggler Snaptoggle Anchor. Install to Drywall: use Toggler Snaptoggle Anchor and screws (supplied), see instructions next page.

10 Mount Column to Wall – Snaptoggle Anchor Installation Jaymil Ergo & Office Solutions 150 Dow Street, Tower 4, Manchester, NH Drill ½” hole. Hold metal channel flat alongside plastic straps & slide channel through the hole. Minimum clearance behind wall: only 1 7/8". Hold ends of straps together between thumb & forefinger and pull toward you until channel rests behind wall. Ratchet cap along straps with other hand until flange of cap is flush with wall. Place thumb between straps at wall. Push thumb side to side, snapping off straps level with flange of cap. You should have the flange like the below at this point. Position brackets over flange. Insert bolt and tighten until snug against item, then stop. Use supplied ¼-20 Bolt. Be sure to check level before tightening bolt down. Level can be adjusted slightly at this point.

11 Mount Column to Wall Jaymil Ergo & Office Solutions 150 Dow Street, Tower 4, Manchester, NH The column should now be mounted to the wall and bolted at all 4 mounting points.

12 Install Counter – Pull and Swivel Jaymil Ergo & Office Solutions 150 Dow Street, Tower 4, Manchester, NH Mount Counter to Pull and Swivel Head by screwing bracket to counter from underneath. Mount counter off center based on how you want the counter to swivel. Tip: move Pull and Swivel Head to access all screw holes.


Download ppt "Stable Rise –Pull and Swivel Top Installation and Set Up Guide Jaymil Ergo & Office Solutions 150 Dow Street, Tower 4, Manchester, NH 603.629.9995."

Similar presentations


Ads by Google