Presentation is loading. Please wait.

Presentation is loading. Please wait.

Getting Started with your Diagnostic Station Getting Started with your Diagnostic Station.

Similar presentations


Presentation on theme: "Getting Started with your Diagnostic Station Getting Started with your Diagnostic Station."— Presentation transcript:

1

2 Getting Started with your Diagnostic Station Getting Started with your Diagnostic Station

3 Your ADC ADVIEW Diagnostic Station Unpacking the contents, you will find… Quick start guide (a printed version of these instructions)Quick start guide (a printed version of these instructions) Tray of accessories for the configuration of the diagnostic station you purchasedTray of accessories for the configuration of the diagnostic station you purchased ADC ADVIEW in your chosen configuration.ADC ADVIEW in your chosen configuration. Unpacking the contents, you will find… Quick start guide (a printed version of these instructions)Quick start guide (a printed version of these instructions) Tray of accessories for the configuration of the diagnostic station you purchasedTray of accessories for the configuration of the diagnostic station you purchased ADC ADVIEW in your chosen configuration.ADC ADVIEW in your chosen configuration. BPBP, TemperatureBP, SpO 2 BP, SpO 2, Temperature

4 Mounting the ADC ADVIEW Included with your ADC Adview is one of the following mounts. Click to view mounting instructions for each. Wall mountTabletop standMobile stand Need Help?

5 Mounting to the tabletop stand Using the thumb screws, secure the rear panel of the BP device to the tabletop stand. Secure power supply with velcro ® strap provided on bottom of the cradle. Using the thumb screws, secure the rear panel of the BP device to the tabletop stand. Secure power supply with velcro ® strap provided on bottom of the cradle. Go to setup Need Help?

6 Mounting on the wall 1. 1.Attach the bracket to the wall using 4 wall screws, and the basket using 2 screws Attach the wall bracket adapter to the rear panel of the BP device using the 3 screws Position the adapter onto the rivets of the wall bracket and slide the device down until it locks into place Attach the bracket to the wall using 4 wall screws, and the basket using 2 screws Attach the wall bracket adapter to the rear panel of the BP device using the 3 screws Position the adapter onto the rivets of the wall bracket and slide the device down until it locks into place Go to setup Need Help?

7 Mounting to the mobile stand 1. 1.Assemble the mobile stand according to the manufacturer’s directions Using the three thumb screws, secure the rear panel of the BP device to the stand Assemble the mobile stand according to the manufacturer’s directions Using the three thumb screws, secure the rear panel of the BP device to the stand. 1 2 Go to setup Need Help?

8 First time setup If your Adview includes… 1.The temperature module Prepare it for use Prepare it for use Set the unit for measurement Set the unit for measurement 2.The pulse oximetry module Connect the SpO 2 sensor Connect the SpO 2 sensor 3.A rechargeable battery Charge the battery Charge the battery If your Adview includes… 1.The temperature module Prepare it for use Prepare it for use Set the unit for measurement Set the unit for measurement 2.The pulse oximetry module Connect the SpO 2 sensor Connect the SpO 2 sensor 3.A rechargeable battery Charge the battery Charge the battery Temperature BP SpO 2 Battery (internal) Follow the next four slides as they apply to the configuration of your device. Need Help?

9 Preparing the temperature module for use 1. 1.Remove tape from the temperature probe Place the probe cover box into the holder Remove tape from the temperature probe Place the probe cover box into the holder. 2 Need Help? 1

10 Connecting the SpO 2 sensor Connect the sensor to the extension cable Flip the retention clip forward, towards the display of the module. Connect the cable to the device Finally, push the clip backward over the SpO 2 connector to hold the connector in the device 1. 1.Connect the sensor to the extension cable Flip the retention clip forward, towards the display of the module. Connect the cable to the device Finally, push the clip backward over the SpO 2 connector to hold the connector in the device Need Help?

11 Connecting power 1.Connect the power supply to the BP module. 2.Connect the power supply to an AC main power source. The device will turn on automatically. 1.Connect the power supply to the BP module. 2.Connect the power supply to an AC main power source. The device will turn on automatically. Note: For devices with a rechargeable battery, connect to an AC main power source for eight hours in order to fully charge the battery. 1 2 Need Help?

12 Changing the unit of temperature measurement While the unit is powered on, use the end of a paper clip or similar tool to press the recessed button on the temp module. The icon for the selected unit is displayed. Need Help?

13 Attaching the Quick Reference Card to the Basket Use the four plastic ties to attach the numbered cards to the front side of the basket. Need Help?

14 Overview of the ADC Adview BP Module Pressure column 1 bar = 10mmHg Automatic button Manual button Warning icon Cuff/Hose Error icon Systolic BP/ Cuff pressure Diastolic BP Pulse rate icon MAP icon Pulse rate/ Mean Arterial Pressure (MAP) Need Help?

15 Overview of the fully configured ADC Adview Temperature Mode button Retention clip Temperature Module Signal quality Need Help? BP Module SpO 2 Module

16 Need help? Contact us by telephone: or or Or by Or find help on the Internet: Contact us by telephone: or or Or by Or find help on the Internet:


Download ppt "Getting Started with your Diagnostic Station Getting Started with your Diagnostic Station."

Similar presentations


Ads by Google