Presentation on theme: "Module 3: Marking out and Hand Tools"— Presentation transcript:
1 Module 3: Marking out and Hand Tools Mechanical Workshop
2 Module ObjectivesAfter the completion of this module, student should be able to:Identify different marking out tools and their usage.Select the appropriate tool required for marking out.Mark out work-pieces according to the dimensions given in engineering drawings.Distinguish the different hand tools and their uses.Select the correct tool for the task.State the care and safe use of hand tools.
3 3.4 Introduction to hand tools The mechanical engineer very often have to use a number of various hand tools in the course of his duties as a fitter or machinist, many of these tools are common to both.
4 1- Spanners/ WrenchesThe two words “spanner” (in British English) and “wrench” (in American English) refer to the same tool.Spanners/Wrenches are different in shape to provide ease of operation under certain conditions.They are manufactured from high tensile or alloy steel.The sizes of metric spanners are identified by the distance across flats of a nut or bolt head
5 The sizes of metric spanners are identified by the distance across flats of a nut or bolt head S=24 mm
6 Spanner types 1-1 Open-ended spanners The ends of this type of spanners are generally oriented at an angle of 15º to the longitudinal axis of the handle to allow greater range of movement in enclosed spaces. An open-end wrench has two different sizes; one at each end.
9 1-2 Ring spannersRing spanners or box-end wrenches are recommended to be used when a better grip is needed and when the spanner swing is restricted.
10 A box-end wrench has two different sizes; one at each end.
11 1-3 Combination spanners This type comes with an open end from one side and a ring end from the other side . Usually both ends are having the same size
12 1-4 Adjustable spannersAdjustable spanners are spanners that have a moving jaw to fit different bolt/nut sizes
13 An adjustable wrench is often used where the exact size wrench is not available or when a large nut, such as a wheel spindle nut, needs to be rotated but not tightened.Adjustable wrenches are sized by the overall length of the wrench and not by how far the jaws open.
14 Accidents Prevention When using wrenches When working with spanners, accidents are usually caused by the slipping of a spanner from a nut or bolt head. In order to avoid these accidents, the following recommendations should be considered
15 1- Use the correct size spanner for the job 1- Use the correct size spanner for the job. 2- Pull towards the body whenever possible. 3- Do not obtain extra leverage by using pieces of pipe. 4- Use a steady pull not a jerking action. 5- Do not hit a spanner with a hammer. 6- Make sure your hands will not strike any obstructions.
18 2- Allen keysThey are referred to as Allen keys and sometimes Allen wrenches.Allen keys are used on grub screws and socket head cap screwsThe size of Allen keys is almost like spanners measured across flats.Socket head cap screwAllen KeysGrub screw
19 3- screwdriversScrewdrivers are made in different lengths and designs, the two most common are:Flathead/slottedCrosshead/Phillips
20 The flathead is identified by its length and in some cases by the blade width. The crosshead screwdriver is identified by its point size.
21 Always use the correct size screwdriver for the screw head; the blade should fit the width of the screw head.
23 4- pliersPliers are a hand tool used to hold objects firmly, or for cutting and bending tough materials such as wires.There are different types that can deal with different types of jobsFlat nose pliersLong nose pliersCombination pliersCirclip pliers
24 4-1 long nose pliersLong nose pliers are both cutting and gripping pliers used by electricians and other tradesmen to bend, re- position and cut wire.
25 4-2 combination pliersThese pliers incorporate side cutters, joint cutters and pipe grip.
26 4-3 circlip pliers Circlips are retaining devices They are fitted inside a groove on bores and shaftsThe internal circlip has to be squeezed to be removed
27 The external circlip which is fitted onto a shaft has to be opened out to be removed
28 The nose of the circlip plier is either straight or bent depending on the type of job.
29 5- Pipe wrenchA pipe wrench is designed to tighten its grip on the part being rotated. It has serrated jaws that leave marks on the part and so it might damage the surface of the part. Accordingly, pipe wrenches must not be used to loosen a nut, unless the nut is to be replaced.