Presentation is loading. Please wait.

Presentation is loading. Please wait.

200 pt 300 pt 400 pt 500 pt 100 pt 200 pt 300 pt 400 pt 500 pt 100 pt 200pt 300 pt 400 pt 500 pt 100 pt 200 pt 300 pt 400 pt 500 pt 100 pt 200 pt 300 pt.

Similar presentations


Presentation on theme: "200 pt 300 pt 400 pt 500 pt 100 pt 200 pt 300 pt 400 pt 500 pt 100 pt 200pt 300 pt 400 pt 500 pt 100 pt 200 pt 300 pt 400 pt 500 pt 100 pt 200 pt 300 pt."— Presentation transcript:

1 200 pt 300 pt 400 pt 500 pt 100 pt 200 pt 300 pt 400 pt 500 pt 100 pt 200pt 300 pt 400 pt 500 pt 100 pt 200 pt 300 pt 400 pt 500 pt 100 pt 200 pt 300 pt 400 pt 500 pt 100 pt Bench Grinder Drill PressTable SawGeneral Oxy- acetylene

2 Stand here when turning on the grinder. Bench Grinder

3 What is stand to the side? Bench Grinder

4 Grind metal on the proper surface of the wheel. Bench Grinder

5 What is grind on the face of the wheel, not the side? Bench Grinder

6 The best tool to hold metal when grinding. Bench Grinder

7 What is vice-grips? Bench Grinder

8 When finished grinding, turn off the machine and wait for wheels to stop. Bench Grinder

9 What is don’t stop the grinding wheel by forcing metal into it? Bench Grinder

10 Properly position the tool rest to the grinding wheel. Bench Grinder

11 What is 1/8” away and in the center of the wheel? Bench Grinder

12 Drill Press Technique used to keep the bit cool while drilling.

13 Drill Press What is squirt cutting fluid on the bit while drilling?

14 Drill Press Used to tighten or loosen the chuck and bit.

15 Drill Press What is the chuck key?

16 Drill Press Some materials should be secured with a vice or clamp when drilling.

17 Drill Press What are small or awkward pieces of wood or metal?

18 Drill Press Changing bit speed on the drill press.

19 Drill Press What is unplug the machine and adjust the belts?

20 Drill Press The rule of thumb for speed adjustment when drilling.

21 Drill Press What is drill slower in metal and faster in wood?

22 Table Saw Stand on the right side of the blade

23 Table Saw Where is the correct place to stand when operating the table saw?

24 Table Saw The proper blade height above the wood.

25 Table Saw What is ¼” or less?

26 Table Saw This tool is required in ripping boards less than 6 inches wide.

27 Table Saw What is a push stick?

28 Table Saw A guide used to cut boards to an accurate width on the table saw.

29 Table Saw What is the Rip Fence?

30 Table Saw Small piece of metal with ridged teeth on the back side of the blade.

31 Table Saw What us kick back prevention device?

32 General Proper safety for eyes.

33 General What is wear safety glasses at all times in the shop?

34 General Before adjusting power tools and machines.

35 General What is unplug by pulling on the plug, not the cord?

36 General Oil is spilled on the shop floor.

37 General What is clean up immediately and use floor dry if available?

38 General Keep adequate ventilation in the paint room.

39 General What is close the door and turn on the fan (possible – crack windows)?

40 General Be responsible for what you purchase or bring to the shop.

41 General What is put your name on all project materials?

42 Oxyacetylene You should consider this material to be hot at all times.

43 Oxyacetylene What is metal laying in the shop in the welding area?

44 Oxyacetylene Color of hose and cylinder for oxygen.

45 Oxyacetylene What is green?

46 Oxyacetylene Uses flint to create a spark.

47 Oxyacetylene What is a striker?

48 Oxyacetylene Flame with more oxygen than acetylene.

49 Oxyacetylene What is oxidizing?

50 Oxyacetylene Used to heat large pieces of metal.

51 Oxyacetylene What is a rose bud tip?

52 Final Jeopardy Category: Band Saw

53 Final Jeopardy Answer: Cuts made perpendicular to the actual line to make cutting easier.


Download ppt "200 pt 300 pt 400 pt 500 pt 100 pt 200 pt 300 pt 400 pt 500 pt 100 pt 200pt 300 pt 400 pt 500 pt 100 pt 200 pt 300 pt 400 pt 500 pt 100 pt 200 pt 300 pt."

Similar presentations


Ads by Google