Presentation is loading. Please wait.

Presentation is loading. Please wait.

The Dryerbox ® is a UL classified metal receptacle that installs in the wall behind the dryer and facilitates the collection of the flex exhaust hose.

Similar presentations


Presentation on theme: "The Dryerbox ® is a UL classified metal receptacle that installs in the wall behind the dryer and facilitates the collection of the flex exhaust hose."— Presentation transcript:

1 The Dryerbox ® is a UL classified metal receptacle that installs in the wall behind the dryer and facilitates the collection of the flex exhaust hose. It provides almost two additional square feet of living area, lessens the risk of lint build-up and provides energy savings by removing the kinks usually found in the flex hose.

2 Don’t Build A Home Without It Have a washer and dryer at home? Good chance the dryer is five or six inches away from the back wall and the flex exhaust hose resembles a snake. “Tight bends in the flex exhaust hose accelerate lint accumulation and can really impair the efficiency of the dryer and worse yet, create a fire hazard,” says Rick Harpenau, owner of In-O-Vate Technologies, Inc. and inventor of The Dryerbox ®. The 21 inch high molded box will house and collect the flex transition hose allowing the clothes dryer to be installed right against the wall. Eliminating the bends in the flex exhaust hose provides for better, less restrictive airflow, which in turn minimizes lint buildup, saves energy costs and reduces the serious fire hazard caused by lint build-up.

3 Specification Model NumberWall SizeExhaust Direction 4252x6Upward * 3502x4Upward 4D2x6Downward 3D2x4Downward * For stackable or pedastal dryers with downward exhaust direction install this model upside-down For a complete and detailed specifications and dimension, visit

4 Performance Data For Use: Dryer vent hose receptacle Doubles as gas connection receptacle Meets code requirements as a clean-out Materials: Model 425 and 350 deep drawn with.028 aluminized steel (22 gauge) Model 4D and 3D deep drawn with.031 aluminized steel (21 gauge) UL Classified for a one hour wall Made in the USA US Patent 5,476,183 and 6,419,102

5 Are you considering a plastic dryer vent receptacle? Time elapsed for fire to penetrate wall cavity: 1 minute 20 seconds 30 seconds60 seconds110 seconds 400 degrees550 degrees800 degrees

6 Our metal receptacle is approved by Underwriters Laboratories for a One-Hour wall installation Time elapsed for fire to penetrate wall cavity: No Penetration 5 minutes30 minutes1 hour 700 degrees1000 degrees1450 degrees

7 Features & Benefits Features: No trim-ring piece is needed Elbow eliminator … gain 5 foot of duct run Surface is paintable, no masking needed Applauded by Mechanical Inspectors Over 1 MILLION installed Benefits: Locate the dryer right up against the wall Flex is protected from getting squished Lint build-up is minimized Efficiency is increased … clothes dry faster Dryer related service calls are almost eliminated Laundry room appears larger to prospects Reduces the fire hazard

8 Contractor Benefits For The Building Contractor The Dryerbox® is sized (10” in width) to fit within 12”, 16” or 24” center studs. It only needs connection at three corners so no additional framing is needed. It is a very rigid 22 gauge aluminized steel with a Classification from United Laboratories to allow its installation in a one-hour rated wall assembly. It’s 20” height provides for sufficient room to store the recoiled aluminum flex. For The Plumbing Contractor The Dryerbox® features a “knock-out” port for a gas line, allowing for a convenient and space saving location of the gas valve and fittings. For The Drywall Contractor The extension rim on The Dryerbox® protrudes 7/8” from the nailing flange offering a built-in corner bead. A Roto-zip (spiral saw) tool will cut out the opening just like any other receptacle, leaving a small crevice that gets caulked by the painter when he caulks the baseboard. The Dryerbox® is metal so the zip-cut bit head will not gum up with plastic like other large receptacles cause.

9 Contractor Benefits For The Trim Carpenter The extension rim on The Dryerbox® protrudes about 1/4” providing enough of a edge to butt the baseboard to. The easiest and best looking saw-cut is just a slightly back-cut angle. The Dryerbox® should not be installed above the baseboard as this defeats the purpose of the receptacle providing a space to protect the flex transition hose. All typical American dryers vent in the same location: at the very bottom and in the center of the appliance. For The Painting Contractor After the drywall contractor “zip-cuts” around The Dryerbox® receptacle, there is a small crevice between the drywall and the metal box that is easily filled with caulk. This built-in corner bead rim protects the drywall from damage and provides enough of a reveal for the trim carpenter to butt his baseboard to. The surface is already prepared for painting. No masking is necessary. “Orange Peel” and wall paint right over the aluminized steel.

10 Distributed By: [your LOGO here] Company Name: [your company name here] Location: [your address, phone, fax, website, ] Available at your local HVAC supply house


Download ppt "The Dryerbox ® is a UL classified metal receptacle that installs in the wall behind the dryer and facilitates the collection of the flex exhaust hose."

Similar presentations


Ads by Google