We think you have liked this presentation. If you wish to download it, please recommend it to your friends in any social system. Share buttons are a little bit lower. Thank you!
Presentation is loading. Please wait.
Published byCassandra Leedom
Modified over 2 years ago
Solar Bike Install Jim Hickey
MDF board cut to profile of a Deuter handlebar bag, board with gal straps and machine screws fitted for concept proof
Another view showing mounting arrangement and foam shock absorbers.
With the Deuter handlebar bag fitted
Controller is now fitted in bag.
Controller is retained at top by the center machine screw engaging in the extrusion
View from the riding position showing the controller bag mounted via a handlebar basket bracket on the headstem and the thumb throttle just inboard of the right gear selectors
Right hand side view showing battery mounting
Looking up at the left side of the front axle showing the re-worked axle tab washers and the press fit of the washer into the fork.
Looking up at the right side of the front axle showing the re-worked axle tab washers and the press fit of the washer into the fork.
All of the wiring connected to the controller and ready to test
All closed up, controller now hidden by a plain bag, wires neatly routed to battery, motor and throttle
How it looks from the riding position
Left hand side view showing battery installation and battery power wires routed alongside battery bracket, up to the handlebar basket bracket (secured with cable tie) and then into the bag
Just a shot to show how clean the install looks
And one last pic for luck
AVIVA™ ELECTRIC BIKES VIPER ASSEMBLY INSTRUCTIONS Aviva™ - For A New Way Of Life.
1 STEPMILL 7000 PT ASSEMBLY INSTRUCTIONS PART NUMBER
XR621 Drive Hose Update Kit. Removal Turn off Battery dis Drain hydraulic tank Remove both rubber lines under chassis and discard. Remove and discard.
ASSEMBLY INSTRUCTIONS. 2 ASSEMBLY INSTRUCTIONS TOOLS REQUIRED: SIDE CUTTING PLIERS PRY BAR 7/16” & 9/16” WRENCH 3/16” ALLEN WRENCH T-15 TORQUE.
1 FREE CLIMBER 4400 ASSEMBLY INSTRUCTIONS PART NUMBER
Dishwasher Rework. Identify Unit Disconnect Power Turn off Breaker… … or unplug power cord.
Levolors New Size-In-Store Blind Cutting Machine.
Helmet Light User Instructions Rotate Tail cap counter clock wise to open battery compartment IR / IFF lever (only functional light In this mode) Two functional.
Memory Craft Feed Dog Drop Step Motor Adjustments.
Supermicro © 2009Confidential MCP N installation guide Rech Weng.
Robot Build IT Girls Allowed 2014 Updated 14 th August.
L.C. Technology ROBOT ASSEMBLY. Base Assembly BASE File off raised tabs on each side of Servo. Place Servo in vice between Fibre Clamps. Raised Tabs Repeat.
Simple Machine Test Put your name at the top of your paper. Number your paper from 1 to 10. Good Luck.
Building a Computer Kate Chapin Capstone Project.
Optical Manufacturing Solutions 1 Probe Assembly.
Lesson 3 How to Construct Your Own Personal Computer.
Adrian Garza. Composites of structural fibers like carbon are used for the frame Wheels, derailleurs, brakes, and chains, are made with stainless.
Tools you will need #8 Torx driver #10 Torx driver Standard Phillips screwdriver Small (jewelers)Phillips screwdriver Small standard screwdriver.
Easy Reach 7.0 Honda Element Packing List QtyDescriptionPacked 115ft 10ga Red Wire 16ft 10ga Black Wire 140amp Breaker 23/8 Yellow Ring Terminals 25/16.
SweepBot is a cleaning robot that cleans floor as brushes spin on High-speed DC Motor. Sweep.
Kit includes: New Sprocket New Upper Bracket New Stickers New Ground Wires Toaster Speed Conversion Kit.
Wiring the PIC Robot. Microcontroller Circuit Left Sensor Right Sensor Left Motor Right Motor To PIC Programmer L293D
Assembly Manual Mike Fortney 04/02/2006 CricketSat Receiver.
Rut ‘n’ Strut Game Calls How I turn a Pot Call. Select wood that you want to use to turn Pot Calls out of, Rip it 4” wide and then Crosscut into 4” X.
WeldingRod’s Exactly Constrained 3D Printer Plate Identification and Stuffing.
2000 Chevy S-10 Left Suicide Door Install Instructions 1.Remove seat (4 anchor bolts.) 2.Remove tracks from seat. To access the nut shown in pic 1, pry.
PRODUCTS SYSTEMS STEM Teachers Summit Hardware Build Manual.
#30 Ignition/Starter Switch #54 To Radio Fuse 1 Instrument Power Ignition Coil Red wire with bullet Long black wire with bullet. Wire was.
Electrical Wiring Circuit Board Project. STEP 1 - Identify all Parts of the Project Saw Drill Driver w/ bits Drill w/bits (not pictured) #2 Phillips Screwdriver.
Assembly Manual Mike Fortney 04/09/2004 CricketSat Receiver.
ELECTRIC VEHICLE PROJECT CAR BUILDING PROCEDURES BY: PIERRE PEASHA CENTENNIAL HIGH SCHOOL BAKERSFIELD, CA.
Instructions for making plunger fork tool. Drawing for the trigger assembly.
Figure 12.1 The UP1-bot. Figure 12.2 Left: Radio Control Servo Motor and Right: Servo with Case and Gears Removed.
Velocette Side panel fixings Images and measurements provided by George Tofield Presentation by Mark Rayner Sept 2012.
6/9/2016 Quick Reference Parts Guide Introduction This Quick Reference Parts Guide is an easy way to locate part numbers to common replacement parts. It.
Step 1: Tools & Components This is a primer project which covers following concepts- 1.Power Supply.or 12v battery 2.DPDT switch operation. 3.DC.
To install the four wires from the back of the coil machine, loosen the four knobs. Keep each wire in center under each knob, off to the side will allow.
CERT MEOC Mobile Emergency Operations Center Concept designed by Keith Morin & Associates - Tucson, AZ.
Princeton University Prospect Eleven Nov. 17, 2005 Mechanics Design and Fabrication of: Vehicle Actuators –Steering –Brakes –Transmission Sensor Housings.
Perry Lapper Progress. Frame With Actuators Outside Frame.
Simple machine A simple device or invention for altering the magnitude or direction of a force. The six basic types are the lever, wheel and axle, pulley,
Photos and Sensor Instructions
Equipment for Assembly Fluke Multimeter 115 True RMS Glue Ring Jig Flathead screwdriver 60 Watt desk lamp HIOS Cl 4000 Electric screw driver Anti-static.
Stable Rise – Fixed Bracket / Stationary Top Installation and Set Up Guide Jaymil Ergo & Office Solutions 150 Dow Street, Tower 4, Manchester, NH
STELR Solar Car construction notes Based on slides provided by Helen Marussinszky, Mitcham Girls HS, South Australia.
1 MOMENTUM 3800 RC ASSEMBLY INSTRUCTIONS PART NUMBER
Making A Motor Exploring the Magic of Electricity.
Brakes Yes, they are Important!
© 2017 SlidePlayer.com Inc. All rights reserved.