Presentation is loading. Please wait.

Presentation is loading. Please wait.

10/11 CLI 說明 : ALU 常用指令簡介 James. Poke commands Step1: Right click NE and select Poke Commands -> TI Wizard.

Similar presentations


Presentation on theme: "10/11 CLI 說明 : ALU 常用指令簡介 James. Poke commands Step1: Right click NE and select Poke Commands -> TI Wizard."— Presentation transcript:

1 10/11 CLI 說明 : ALU 常用指令簡介 James

2 Poke commands Step1: Right click NE and select Poke Commands -> TI Wizard

3 Step1: Scroll down the command list to select command.

4 show NE alarm op:cell ***, extern Acknowledgement from Network element for command op:cell 969,extern is PF M 19 REPT:CELL 969 ASSEMBLAGE 1 ALARM SCANNING SCAN POINT: ALARM GROUP 2, ALARM ID 7 ALARM: SMR MINOR ALARM 告警陳現 STATE: OFF NORMAL 10/09/13 Wed 17:19:44 #034018 M 20 OP:CELL 969 EXTERN, COMPLETED 10/09/13 Wed 17:20:07 #034119

5 查詢基站狀態 -1 op:cell *** Acknowledgement from Network element for command op:cell 815 is IP all specified cells ACT 35 OP:CELL 815 DL 0 CONNECTED, RCS ACTIVE data link 0 : connected 狀態,對應的 RCS 為 active 狀態 10/07/13 Mon 17:35:51 #751738 35 OP:CELL 815 DL 1 CONNECTED, RCS STANDBY data link1 : connected 狀態,對應的 RCS 為 standby 狀態 10/07/13 Mon 17:35:51 #751739 M 35 OP:CELL 815 CDM 1, CRC, ACTIVE CDM1 一般為 1X 服務,其 CRC 無線控制器是啟動的狀態 CHILD DO CRC 3 SIGNALING LINK ACTIVE ON CRC 1, SHARING WITH CRC 3 信令鏈路啟用於 CRC 1(1X) ,同時與 CRC 3(EVDO) 共享 MANU NEG, 100 MBPS, FULL DUPLEX, VLAN ID 1612 CDM 1 的 CRC 上的 Ethernet 狀態為 100Mbps/ 全雙工 /vlan ID=1612 10/07/13 Mon 17:35:51 #751740

6 M 35 OP:CELL 815 CDM 3, CRC, ACTIVE PARENT CRC 1 SIGNALING LINK ACTIVE MANU NEG, 100 MBPS, FULL DUPLEX, VLAN ID 2612 DO TRAFFIC LINK ACTIVE 10/07/13 Mon 17:35:51 #751741 M 35 OP:CELL 815 CDM 1, 3, CBR 1, 10MHzI, ACTIVE DIV NORMAL 10/07/13 Mon 17:35:51 #751742 M 35 OP:CELL 815 CDM 1, 3, CBR 2, 10MHzI, ACTIVE CDM:1 、 3(1X&EVDO) 所使用的 CBR 2 基帶無線模組 #2(beta 扇區 ) 為啟動 DIV NORMAL 分集接收正常 10/07/13 Mon 17:35:51 #751743 M 35 OP:CELL 815 CDM 1, 3, CBR 3, 10MHzI, ACTIVE DIV NORMAL 10/07/13 Mon 17:35:51 #751744 M 35 OP:CELL 815 CDM 3, CBR 4, 10MHzI, ACTIVE DIV NORMAL 10/07/13 Mon 17:35:51 #751745 查詢基站狀態 -2

7 M 35 OP:CELL 815 CDM 3, CBR 5, 10MHzI, ACTIVE DIV NORMAL 10/07/13 Mon 17:35:51 #751746 M 35 OP:CELL 815 CDM 3, CBR 6, 10MHzI, ACTIVE DIV NORMAL 10/07/13 Mon 17:35:51 #751747 查詢基站狀態 -3

8 重置 TFU : RMV+RST RMV:CELL ***,TFU 1;UCL RST:CELL ***,TFU 1;UCL RMV:CELL 1059,TFU 1;UCL Acknowledgement from Network element for command RMV:CELL 1059,TFU 1;UCL is IP all specified cells ACT M 09 RMV:CELL 1059 TFU 1, COMPLETED 05/15/12 Tue 15:09:13 #191309 M 09 OP:CELL 1059 TFU 1, OOS, MANUAL, RMVD GPS INDT, OM INDT GPS 狀態由 normal 變為 iINDT 05/15/12 Tue 15:09:13 #191310 RST:CELL 1059,TFU 1;UCL Acknowledgement from Network element for command RST:CELL 1059,TFU 1;UCL is IP all specified cells ACT M 13 RST:CELL 1059 TFU 1, COMPLETED 05/15/12 Tue 15:13:55 #191685 M 13 OP:CELL 1059 TFU 1, ACTIVE GPS NORMAL, OM ONBOARD NORMALGPS 狀態恢復 normal

9 查詢基站 RSSI op:cell ***,cdm *,cbr * rssi OP:CELL 1046, CDM 1, CBR 2 RSSI 顯示目前 CDM 1(1X), CBR 2( 第二扇區 ) 目前的 RSSI Acknowledgement from Network element for command OP:CELL 1046, CDM 1, CBR 2 RSSI is IP all specified cells ACT M 04 OP:CELL 1046 CDM 1, 3, CBR 2, ACTIVE DIV_IMB THRESHOLD: 5.0ANTENNA DIVERSITY IMBALANCE = 主副集接收差異告警門限 =5dBm RSSI RX1:-63.1dBm RSSI RX2: -68.3dBm 主集接收副集接收的強度,此例中基站 ”1046” 的主副集相差 5.2dBm 故會報 告警 05/14/12 Mon 15:04:05 #088476

10 基站重啟 (Reset Cell without restart RCS application in AP (stable clear)) INIT:CELL *** :SC Acknowledgement from Network element for command init:cell 1603:sc is OK **39 RCVRY:CELL 1603 PHASE STARTED, CP ALW, PH LVL SC, PH SRC MCRT 10/02/13 Wed 09:39:17 #390716 **43 RCVRY:CELL 1603 PHASE COMPLETED, CP ALW, PH LVL SC, PH SRC MCRT 10/02/13 Wed 09:43:14 #391756 Session activity timer has expired. Please close inactive OMC-RAN TICLI Acknowledgement from Network element for command init:cell 1782:sc is OK **33 RCVRY:CELL 1782 PHASE STARTED, CP ALW, PH LVL SC, PH SRC MCRT 10/08/13 Tue 10:33:46 #553120 **37 RCVRY:CELL 1782 PHASE COMPLETED, CP ALW, PH LVL SC, PH SRC MCRT 10/08/13 Tue 10:37:48 #554231 Session activity timer has expired. Please close inactive OMC-RAN TICLI 基站重啟 (Reboot Cell and it’s associated RCS in AP) RST:RCS XXX 新開基站必須使用這條命令重起 RCS 與基站

11 重置 CBR : RMV+RST RMV:CELL ***,TFU 1;UCL RST:CELL ***,TFU 1;UCL 重置 CCU : RMV+RST RMV:CELL ***,CDM *,CCU * ;UCL RST:CELL ***,CDM *,CCU * ;UCL CBR x — CDMA Baseband Radio (CBR) CCU x — CDMA Channel Unit (CCU) CRC x — CDMA Radio Controller (CRC) UCL Unconditionally remove the unit from service bypassing threshold checks. Acknowledgement from Network element for command RMV:CELL 1053,CDM 1,CBR 1;UCL is IP all specified cells ACT M 44 RMV:CELL 1053 CDM 1, 3, CBR 1, COMPLETED 05/11/12 Fri 17:44:12 #775813 M 44 OP:CELL 1053 CDM 1, 3, CBR 1, 10MHzI, OOS, MANUAL, RMVD RMV 後 CBR 1 變成 OOS TXPORT 1 DISABLED ASMB 1 TXAMP 1 ACTIVE ASMB 1 RXAMP 1 NORMAL TTLNA 1 NORMAL ASMB 1 RXAMP 2 NORMAL TTLNA 2 NORMAL DIV INDT 05/11/12 Fri 17:44:12 #775814

12 查看基站底躁 dump:cell ***;plm 9;carrier *,sector * ( 下行信号 ) 9 — Total Output Power on Forward Link. Acknowledgement from Network element for command dump:cell 2387;plm 9;carrier 1,sector 1 is IP all specified cells ACT M 22 DUMP:CELL 2387 PLM 9 CARRIER: 1 SECTOR: 1 TOTAL OUTPUT POWER ON FORWARD LINK PART: 1 27 27 28 29 29 29 28 28 29 30 29 28 28 28 28 27 27 27 27 27 27 27 28 28 28 28 28 29 30 30 29 29 29 29 29 30 30 30 29 29 30 30 30 29 29 29 28 28 28 28 28 28 28 28 29 29 30 29 29 29 29 29 29 29 29 29 28 28 28 28 28 28 28 28 28 28 29 29 29 30 29 28 28 28 29 30 29 29 28 28 29 29 29 29 29 30 29 28 28 28 28 28 29 29 29 29 29 29 29 28 28 28 28 29 29 28 28 29 30 31 31 30 31 30 31 30 31 31 30 30 31 30 32 33 32 31 30 30 31 30 30 31 30 30 30 30 30 30 30 30 29 29 29 29 29 30 30 29 29 28 28 28 29 29 29 29 28 28 28 29 28 28 28 29 29 28 29 29 29 28 28 29 29 28 28 28 28 28 28 28 28 28 28 28 29 28 29 29 30 30 29 29 29 29 29 28 28 28 28 28 28 28 28 28 29 29 29 29 29 29 29 29 29 29 29 10/08/13 Tue 18:22:19 #054414

13 dump:cell ***;plm 10;carrier *,sector * 10 — Noise Rise (Median and Delta Rise) Acknowledgement from Network element for command dump:cell 2387;plm 10;carrier 1,sector 1 is IP all specified cells ACT M 38 DUMP:CELL 2387 PLM 10 CARRIER: 1 SECTOR: 1 50TH PERCENTILE REVERSE LINK NOISE POWER -84.50dBm -84.50dBm -84.50dBm -84.50dBm -84.50dBm -84.50dBm -84.50dBm -84.50dBm -84.50dBm -84.00dBm -84.00dBm -84.25dBm -82.00dBm -84.50dBm -84.25dBm -84.00dBm -84.50dBm -84.50dBm -84.50dBm -84.50dBm -84.50dBm -84.50dBm -84.50dBm -84.50dBm -84.75dBm -84.75dBm -84.75dBm -84.50dBm -84.50dBm -84.50dBm -84.50dBm -84.50dBm -84.50dBm -84.50dBm -84.50dBm -84.50dBm -84.50dBm -84.50dBm -84.50dBm -84.50dBm -84.75dBm -84.75dBm -84.75dBm -84.75dBm -84.75dBm -84.75dBm -84.75dBm -84.50dBm -84.50dBm -84.50dBm -84.50dBm -84.50dBm -84.50dBm -84.25dBm -84.50dBm -84.50dBm -84.50dBm -85.00dBm -84.50dBm -84.50dBm -84.50dBm -84.50dBm -84.00dBm -84.00dBm -84.25dBm -84.25dBm -84.00dBm -84.50dBm -84.50dBm -84.50dBm -84.25dBm -84.00dBm -84.25dBm -84.50dBm -84.50dBm -84.50dBm -84.50dBm -84.50dBm -84.25dBm -84.25dBm -84.00dBm -84.00dBm -84.00dBm -84.25dBm 10/08/13 Tue 18:38:50 #058469

14 查看基站線路狀態 (ES.....) EXC:CELL ***,CDM *,DS1 *,REPORT 1 (DS1 * --> 查看第幾條電路 ) Acknowledgement from Network element for command EXC:CELL 2387,CDM 1,DS1 1,REPORT 1 is IP all specified cells ACT M 43 EXC:CELL 2387,CDM 1,DS1 1,REPORT 1 CELL 2387,CDM 1,DS1 1,REPORT 1 DS1 1-UNEQUIPPED 10/08/13 Tue 18:43:15 #059559 Acknowledgement from Network element for command EXC:CELL 898,CDM 1,DS1 1,REPORT 1 is IP all specified cells ACT M 45 EXC:CELL 898,CDM 1,DS1 1,REPORT 1 CELL 898,CDM 1,DS1 1,REPORT 1 DS1 1-CRC IS OOS 10/08/13 Tue 18:45:57 #060234

15 REPORT * 1 — Include only the current 15 minute, number of seconds into current interval, and 24 hour aggregate data. 2 — Include only the specified number-of-hour-shift in the past, in 15 minute increments. 3 — Include only the 24 hour data in 15 minute increments and 24 hour aggregate data. The number of seconds into current 15 minute interval shall also be specified. 4 — Current measured signal level, alarm, loop mode, state, substate, mode, framing, line coding, signaling, line build out, options, chain, clock source, clock priority.

16 基站 PING-1X /DO exc:cell ***,cdm *,crc,ping IP,REPEAT g IX IP=***.193.***.***+1 ; DOIP:***.194.***.***+1 ; g = 1~ 5 1X Gateway(AGP)IP = ***.193.***.***+6 DO Gateway(AGP)IP = ***.194.***.***+6 EX: GN110010 : BTS 1X IP: 10.193.11.0 Acknowledgement from Network element for command exc:cell 130,cdm 1,crc,ping 10.193.11.1,REPEAT 1 is IP all specified cells ACT M 59 EXC:CELL 130, CDM 1, CRC, PING, COMPLETED EXTERNAL SOURCE IP = 10.193.11.1 INTERNAL SOURCE IP = 192.168.208.2 LINKID = 1 DESTINATION IP = 10.193.11.1 PAYLOAD SIZE = 56 BYTES SENT = 56 TIMEOUT = 5 PING HOST TIME STATUS 0 10.193.11.1 1 SUCCESS PACKETS: SENT 1, RCVD 1, LOST 0 (0%) ROUND TRIP TIMES: MIN 1, MAX 1, AVG 1 10/08/13 Tue 18:59:56 #063603

17 基站軟件狀態 : 察看基站內軟體詳細資訊 OP:cell ***, GENERIC Acknowledgement from Network element for command op:cell 130,generic is IP all specified cells ACT M 32 OP:CELL 130 CDM 3 GENERIC, FINISHED GENERIC ACTIVE STATUS F3713EBFA.12 NO GOOD F3713EBFA.38 YES GOOD F3712EBGA.00 NO GOOD 10/08/13 Tue 19:32:21 #071497 M 32 OP:CELL 130 CDM 1 GENERIC, FINISHED GENERIC ACTIVE STATUS F3713DBFA.38 YES GOOD F3712DBGA.00 NO GOOD F3713DBFA.12 NO GOOD 10/08/13 Tue 19:32:25 #071512 M 32 OP:CELL 130 GENERIC, COMPLETED 10/08/13 Tue 19:32:25 #071513


Download ppt "10/11 CLI 說明 : ALU 常用指令簡介 James. Poke commands Step1: Right click NE and select Poke Commands -> TI Wizard."

Similar presentations


Ads by Google