Presentation is loading. Please wait.

Presentation is loading. Please wait.

Click here to add Company Name and Date 2 Parker is the global leader in motion and control technologies, partnering with its customers to increase their.

Similar presentations


Presentation on theme: "Click here to add Company Name and Date 2 Parker is the global leader in motion and control technologies, partnering with its customers to increase their."— Presentation transcript:

1

2 Click here to add Company Name and Date

3 2 Parker is the global leader in motion and control technologies, partnering with its customers to increase their productivity and profitability.

4 3 3 rd Generation post-compensated valve Target Launch – October 2006 Load-Sense Pressure Compensated Valve with Flow-Sharing (Post-Compensated)

5 4 Specifications Flows – Pump input up to 60 GPM –Work sections up to 50 GPM Pressure 5000 PSI Sectional construction Max. porting –Inlet SAE 16 top and side –Work SAE 12 –Outlet SAE 16 top and SAE 20 side

6 5 Model Logic V = valve P = lspc (post-compensated) 170 = max work section flow in LPM Remember the VO40: V = valve O = open center 40 = max work section flow in plum

7 6 Key Features & Benefits Flow-sharing for improved productivity, safety and operator comfort Load-sense pressure compensated for improved system efficiency and fuel savings Modular design enables better match between cost and value. Available with: –Load-sense pressure compensated, with or without induced load protections –Load-sense only Low loop pressure drops for reduced HP consumption Low pressure regeneration to solve cavitation problems of premature component failure and “spongy” operation

8 7 Key Market Drivers Improved machine controllability and productivity Horsepower utilization, due tier II and III engines Fuel cost

9 8 Target Markets Wheel loaders and dozers –Launched to Deere September 2004 for J Series Loaders Cranes Forestry – loaders, feller-bunchers, harvesters, forwarders, skidders Refuse – side loaders Snow and ice Distribution

10 9 Competitors Post-Compensated –Danfoss – PVG100 (new) –Husco – SX180 (new) –Rexroth – SX14? (have not seen in dist’n channel) –Rexroth - M4-15 (120 lpm out of work section) Pre-Compensated –MP18 and MP22 (being discontinued; Wooster closing)

11 10 Flow-Sharing Adjusts to a pump over-demand conditions by reducing the flow to the selected functions, while maintaining the speed relationship between those functions The benefit - the operator can maintain the control of the machine The result - increased productivity, improved safety and operator comfort

12 11 Flow-Sharing Example #1

13 12 Flow-Sharing - Example #1 Full pump flow is 40 GPM, but operator wants 46 GPM Work section flows at full pump displacement of 40 GPM GPM Operator wants 40 GPM from two work sections But now operator wants 46 GPM Only 40 GPM available, so valve goes into over- demand and divides the pump flow accordingly

14 13 Flow-Sharing - Example #2

15 14 Flow-Sharing - Example #2 Engine RPM decreases flow from 40 GPM to 30 GPM GPM Operator wants 40 GPM from two work sections Engine rpm’s drop so max pump flow is 30 GPM; valve divides the flow accordingly Work section flows at full pump displacement of 40 GPM

16 15 Improved Efficiency of PCLS Pressure F l o w Power consumed by function Wasted power L.S. system

17 16 Improved Efficiency of PCLS “A big reason for the change by Deere was mounting fuel costs. The pressure compensated load-sensing variable displacement system is a lot more fuel efficient than the open-center system, depending on operation, by as much as 30, 40, or even 50% better,” says Anders Lindstrom, Senior Systems Engineer with Parker Hannifin. “With the fuel savings I get on two of my 437Cs, I can make the payment on one.”

18 17 Modular Design Offers Three Circuit Options Load sense ck for all circuit options located between the work ports!!! Induced load/ transition ck Compensator 2. Load-sense pressure scompensated (PCLS) w/o induced load protection Compensator 1. Load-sense pressure compensated (PCLS) with induced load protection

19 18 Modular Design Offers Three Circuit Options 3. Load-sense only Transition ck Load sense ck for all circuit options located between the work ports !!!

20 19 Circuit – PCLS with Induced Load Protection Pressure compensated load-sense (PCLS) w/ reverse flow check

21 20 Circuit – PCLS without Induced Load Protection Pressure compensated load-sense (PCLS) w/o reverse flow check

22 21 Circuit – LS only Load-sense valve circuit

23 22 Low Loop Pressure Drop Ports A/B - tank

24 23 Spool Options Types –3 way cylinder and motor –4 way cylinder and motor –4 position float Flows –Flow limited at full stroke and 250 PSI margin GPM 8, 16, 24, 32, 45 Additional flow limitation can be achieved with spool stroke limiters for ports A or B or both. Applies to hydraulic remote and solenoid operated. –Not flow limited Another spool available that falls off the notch at full stroke and will try to output the full pump flow

25 24 Inlet Options

26 25 Inlet Options

27 26 Outlet Options

28 27 Low Pressure Regeneration Low pressure regeneration –Addresses cavitation Cavitation wreaks havoc on hydraulic components and results in spongy machine operation During valve operation, the valve will sense if a function is cavitating and will force oil across anti-cavitation checks to fill void If there is still a void in the hydraulic loop, when spools returned to neutral – will keep pump on stroke until a specified pressure level is achieved in the loop

29 28 Robust Endurance and fatigue testing: –Inlet, work sections and outlet fatigue 6250 PSI and 3M cycles – NO FAILURES –Load-sense checks endurance 5000 PSI and 2M cycles – NO FAILURES –Transition/induced load check 5000 PSI and 1M cycles – NO FAILURES

30 29 Performance Enhancement Meter-out control can increase P-A/B pressure drop, when opposite port energized Work section body lengthened to ensure that pressure drop P/A-B not affected when meter-out control required Port B Tank

31 30 Performance Enhancement 4-position float work section –When work section is in the float position, traditional design will draw oil A and B tank cores VP170 design can draw oil from: –Tank cores of ports A and B –Return flow from port B This improves float down time and addresses potential cavitation

32 31 Additional Benefits Fly cut lands each critical area (10) means consistent metering from valve to valve Uses same spool positioners as VA20 and PC25 — reduces cost, risk and improves delivery Uses same port accessories as FIVE other valve series –– reduces cost, risk and improves delivery Spool stroke of.406" longest in industry — this means more metering vs. spool stroke One solenoid used for on/off and proportional applications

33 32 Summary Pressures to 5000 PSI Flow range is 8-55 gpm out of the work port Flow-sharing Circuit options – load-sense pressure compensated or load-sense Optional induced load protection Optional low pressure regen and void filling scheme Improved filling scheme during float position (4 position float work section) Flexible, compact and cost effective EH package Symmetrical spool for easy conversion to right or left-handed sections Same spool positioners and port accessories as open-center counterparts Stroke limiters available for hydraulic remote and solenoid operation Full complement of flow-limited spools available Easily serviceable — all checks located on top of work section

34 33 VP170 Product Launch Literature –Product Catalog HY /US –Overview Bulletin HY /US –Service Bulletin HY M1/US –Catalog CD HY /US –Advertisement –Product Bit –News Release –To order call CPARKER

35 34 –Complete product information –Applications –Systems and subsystems Hydraulic Valve Solutions For Mobile & Truck Applications

36 35 Contact Us Phone: Fax: Local Parker Distributor

37 36 Thank You! Parker, your single source for all your Hydraulic Valve Solutions.


Download ppt "Click here to add Company Name and Date 2 Parker is the global leader in motion and control technologies, partnering with its customers to increase their."

Similar presentations


Ads by Google