We think you have liked this presentation. If you wish to download it, please recommend it to your friends in any social system. Share buttons are a little bit lower. Thank you!
Presentation is loading. Please wait.
Published byCarley Barr
Modified about 1 year ago
Sandblasted, repainted fender brackets
Mudflaps and rubber buttons to attach them
Mudflap mounted on the fender
Right rear fender mounted in place
Left rear fender mounted in place
A view of the rear fenders mounted
Cooling shroud mounted over the fan
Backed out into the driveway
Problems with the spark plug lead wire from the coil, the NGK end is suspect
Checking wires from the coil to the spark plug
Time for a test drive up and down Tuyll Street
Fantastik does a great job for cleaning the shrouds
Metal heat shield under the shroud protects it from the heat of the muffler pipe
The elbow is turned outwards during summer
Turned inwards in Winter or cold months
Mounted over the exhaust pipe, ready for the large shroud
The flexible union goes between
The big cooling shroud is mounted in place and the air filter box as well
You can see the plastic tray shroud below the fan shroud
One more tray shroud to put in place below the large shroud and attaches to the end of the frame
Shroud installation almost finished – cable to the hot air flap installed
That spring loaded flap must be well greased and/or frequently oiled.
So much for working outside – more now, and lots of it
A new tail light had no wiring, I’ll use the old wiring after cleaning the ends. NEVER throw anything away.
Strip what’s usable and then you can toss the bits
Lower shroud installed – frame rails covered with window glaziers tape ready to mount the furgone
Air tube from the cylinder head exhaust tube attached to the air filter box
Ready to mount the furgone. No pictures of the installation, all hands required
Furgone mounted and backed outside
Lots of bolts and screws to mount it to the frame
Sunshine on the door
¾ view, right side
Right side showing reflectors front and rear
The reflectors help at night
Upper and lower tailgates installed
Extra red reflectors at the rear corners
Furgone interior light
8amp fuseholder for the furgone interior light
And it works but needs attention, quite corroded
Put a drop of oil inside the wire holder caps – stops rust.
Ladybugs spending the Winter on the brake hub and inside the wheel rim.
Outside the body shop. Ready for the ride home Finished doors.
Cobwebs and ladybugs. Pulling the gas tank and other parts.
Driveshaft installed. Bits and pieces – new oil seal.
Vent window installed. Install door frame side latch.
VESPACAR P501 MPR2T TAKE ME TO BAYFIELD KEN THE BUYER.
Starter solenoid, positive battery cable removed.
My furgone watching. Wipe the frame clean Ready to remove the rust.
How to Replace Your Desktop PC’s Power Supply Computer Based Training Objectives.
BMW 1985 – 325e Timing Belt and Water Pump Replacement Start to Finish Take Your Time, Its Not as Bad as It Seems! I was VERY apprehensive about doing.
Cabin beading ends. Cracked cabin beading No rust to speak of.
（ 1 ） PROCEDURE FOR FLAT HEAT PRESS OPERATION PROCEDURE FOR MULTI FUNCTION HEAT PRESS MACHINE.
CLM Maintenance. Covers : 1 - Side cover, 2 - Back cover, 3 Top cover, 4 - Lamp door, 5 - Side cover input and communication side, 6 - HEPA dust filter,
PEUGEOT 206 INSTALLATION 99’— 05’ TU5JP4 1. Remove the air intake system 1.Remove all parts of the air cleaner, intake hose and blow-by hose. 2.
DAILY PRE-TRIP. All bus drivers are to perform a complete pre-trip inspection before the first trip on each and every bus they drive that day. After the.
Getting Ready Gather tools, oil and filter. If you plan to change your oil regularly, consider investing in jack stands, a socket set and an oil drain.
Lighting and Wiring Services. Vocabulary 1.Fusible link 11. open circuit 2.Primary wire 12. short circuit 3.Secondary wire 13. short to ground. 4.Cable.
Chapter 25 Electrical Power Systems. Objectives After reading the chapter and reviewing the materials presented the students will be able to: Summarize.
Framed Canopy Fitting Instructions Contents – 6- Angled frame fixing brackets 1 x handle pack 6 x self drilling tech screws 3 keys 1x door 6 x coach screws.
Installation of heating cables, a light and an outlet with a thermostat and two pole circuit breaker.
Engine Cylinder Leakage Test Tune 8 NATEF Section A8, A.11 P-1.
1 Flywheel 2 Connecting Rod 3 Valve 4 Primer 5. Timing Gear.
AVIVA™ ELECTRIC BIKES VIPER ASSEMBLY INSTRUCTIONS Aviva™ - For A New Way Of Life.
Tom’s Tips for Silencing Your Model “A” 2014 Missouri Valley Region Membership Meet.
SIP POU cooler Installation Guide. Getting Started The SIP 2000 can be easily installed in most POU coolers in just a few minutes. The tools needed are.
Yamaha YDS3 Engine Rebuild Strip and rebuild of a 1965 YDS3 engine.
Cooling Business Group 1 INSTALLATION Directions.
Paint bottom first. Two coats of paint Paint the top last.
Engine Disassembly manual. Oil plugs/ 10 mm wrench.
Engine Reassembly Technicians need to take their time when reassembling an engine. This is not a race! Listen for instruction when to add the next piece.
PHSAUTOMOTIVESALSPHSAUTOMOTIVESALS Tune-up Procedure.
LAB #10. Governor Control Arm Using a 10mm socket install the two bolts that hold the governor control arm. Finger tighten then torque to 100 “#
Suggestion for installation Demolish and destroy the old air condition, then send them to owner building Install a new one by last main.
Stage 1 Turbo kit instructions !!!This kit is for off road use only!!! This kit is NOT emissions legal!!! This kit is perfectly capable of.
The WSF-700 system is designed to control the fan coil valve and the fan speed of the 5 slave zones with a single master thermostat located in a remote.
Cooling System An automobile’s Cooling system is to maintain the engine’s temperature at optimal levels.
Driver Education Objectives/SOL DE.2 The student will demonstrate an understanding of basic vehicle operating procedures. Key concepts/skills include.
Model 12 Intek Horizontal OHV Head Removal and Replacement Lab #5.
97-99 MAXIMA HID PROJECTOR DIY Property of: Imports_only1.
Optical Manufacturing Solutions 1 Probe Assembly.
Electric Wiring Conductor A material that allows electricity to move readily and offers low resistance Example: copper, aluminum and water.
Stable Rise – Fixed Bracket / Stationary Top Installation and Set Up Guide Jaymil Ergo & Office Solutions 150 Dow Street, Tower 4, Manchester, NH
Easy Reach 7.0 Honda Element Packing List QtyDescriptionPacked 115ft 10ga Red Wire 16ft 10ga Black Wire 140amp Breaker 23/8 Yellow Ring Terminals 25/16.
Vacuum system. Principal scheme Vacuum parameters 1 Preliminary vacuum 1*10 -2 Pa 2 Melt storage 5*10 -4 Pa 3 Crystal annealing 5*10 -5 Pa.
How to Build A Computer By John A. Saiz. Materials Required Tools Screw driver Screw driver Tweezers Tweezers Flashlight FlashlightHardware PC Case PC.
By Joseph S.. I suggest: Old Woodward Booth Park.
Lesson 3 How to Construct Your Own Personal Computer.
14.2 Notes – Safety at Home & in School What can cause fires? –cigarettes – careless teenagers thinking the cigarette is out when it’s not, also people.
How to Install A Pop-n-Lock system on F-150 SVT Raptor By: Jacques DuBois.
© 2017 SlidePlayer.com Inc. All rights reserved.