Download presentation

Presentation is loading. Please wait.

Published byArianna Darnley Modified over 2 years ago

1
Velocity Analysis Introduction to Seismic ImagingERTH 4470/5470 Yilmaz, ch 3.1-3.3.2

2
Figs 3-1 to 3-3 Velocities of sediment and sedimentary and volcanic rocks increase with depth. For sediment this is due to compaction of pore space with increasing pressure. Increase in rock velocity is due to closure of cracks with increasing pressure.

3
Normal Moveout (NMO) Correction for Flat Layers

4
For single layer (Figs. 3-4, 3-6 and 3-8). NMO depends on {x 2 /v 2 }, so we need to know v(z) in order to flatten CMP gather before stacking. For brute stack we assume a constant velocity (e.g. water) for simplificity, while knowing that this will not give a good image for deeper structures.

6
For multiple layers, t 2 = t 2 (0) + x 2 /v rms 2, so plots of t 2 vs x 2 will give a straight line with slope of 1/v rms. The root-mean square velocity (v rms ) is determined by eq. 3.4 in terms of the interval velocity (v i ) and travel time (Δt i ) of each layer interval (i). (Figs. 3.9 to 3-11)

8
For “real” data, we expect moveout of reflectors to decrease with depth (=time) as velocity increases with depth due to compaction

9
Various definitions of velocity (Box6.4) Notice difference between v rms and v av but it is small Note also that v nmo = v rms only for the small offset (spread) approximation (Fig. 3-22). For larger spread offsets, the best fit to flatten the actual moveout is not the same.

10
This results in non-linear expansion of the time axis, which is greater for larger x and smaller v. This changes the frequency of the arrivals. (Fig. 3-13 and Table 3-2). When this effect becomes too large (generally in the upper 1-2 sec TWTT), we need to mute the result (Fig. 3-12). This can be done automatically for stretching greater than a certain amount, or by picking the front mutes by hand as we did to remove the refraction arrivals. (Fig. 3-14). For continuous data (not individual picks) we need to flatten arrivals (ie remove increase in t as function of x and v) by stretching the time axis.

12
Methods for Velocity Analysis

13
Synthetic example with 4 layers showing CMP gather, velocity spectrum and t 2 -x 2 plots. Spectrum is unnormalized, cross-correlation sum with a gated row plot.

14
Real example with 4 primary layers and multiple secondary layers. Spectrum is unnormalized, cross-correlation sum with contour plot.

15
Use of constant-velocity gathers (CVG) for a single CMP gather at various velocities to help detail exact nature of stacking velocities

17
Use of constant velocity stack (CVS) for range of gathers at different stacking velocities. Helpful in sections of low signal-to-noise (e.g. at greater depths in the section)

18
Limitations in accuracy and resolution of velocity estimates

19
Synthetic examples of 4 layers showing various plots of velocity spectra. Effect of spread (offset) length

20
Lack of long offsets reduce resolution of lower (high velocity) layers with smaller moveout

21
Lack of near-offsets reduce resolution of shallow layers Partial stacking (using incomplete fold) can save money (computer time) but can result in reduced resolution

22
Reduced resolution caused by decrease in signal-to-noise

24
Effect of dipping layer

25
Effect of dip is only significant when dip angle is large (i.e. > 20 o )

Similar presentations

OK

Basic Seismic Processing INPUT FILTER CMP Gather NMO STACK MIGRATE DISPLAY GEOM VEL ANAL STATICS MUTE.

Basic Seismic Processing INPUT FILTER CMP Gather NMO STACK MIGRATE DISPLAY GEOM VEL ANAL STATICS MUTE.

© 2017 SlidePlayer.com Inc.

All rights reserved.

Ads by Google

Ppt on global warming in hindi language Ppt on working of nuclear power plant in india Ppt on wireless networking technology Ppt on inhabiting other planets outside the solar Ppt on sea level rise in india Ppt on power generation by speed breaker sign Ppt on second law of thermodynamics states Ppt on accounting standards 11 Ppt on grammar in english Ppt online compressor mechanic school